微分法在定位误差分析与计算中的应用

介绍了微分法分析计算定位误差的原理和适用范围,通过生产实例分析,证明了该方法在解决多误差因素定位误差分析与计算中的简便与快捷,从而有效简化了复杂定位方案定位误差的分析与计算,提高了夹具的设计效率。     

Application of small-size antennas for estimation of angles of arrival of HF signals scattered by ionospheric irregularities

A modification of the Doppler Interferometry Technique is suggested to enable estimating angles of arrival of comparatively broadband HF signals scattered by random irregularities of the ionospheric plasma with the use of small-size weakly directional antennas. The technique is based on the measurements of cross-spectra phases of the probe radiation recorded at least in three spatially separated points. The developed algorithm has been used to investigate the angular and frequency-time characteristics of HF signals propagating at frequencies above the maximum usable one (MUF) for the direct radio path Moscow-Kharkiv. The received signal spectra show presence of three families of spatial components attributed, respectively, to scattering by plasma irregularities near the middle point of the radio path, ground backscatter signals and scattering of the sounding signals by the intense plasma turbulence associated with auroral activations. It has been shown that the regions responsible for the formation of the third family components are located well inside the auroral oval. The drift velocity and direction of the auroral ionosphere plasma have been determined. The obtained estimates are consistent with the classical conception of the ionospheric plasma convection at high latitudes and do not contradict the results of investigations of the auroral ionosphere dynamics using the SuperDARN network.     

Multi-mode diagnosis of a gas turbine engine using an adaptive neuro-fuzzy system

Gas Turbine Engines (GTEs) are vastly used for generation of mechanical power in a wide range of applications from airplane propulsion systems to stationary power plants. The gas-path components of a GTE are exposed to harsh operating and ambient conditions, leading to several degradation mechanisms. Because GTE components are mostly inaccessible for direct measurements and their degradation levels must be inferred from the measurements of accessible parameters, it is a challenge to acquire reliable information on the degradation conditions of the parts in different fault modes. In this work, a data-driven fault detection and degradation estimation scheme is developed for GTE diagnostics based on an Adaptive Neuro-Fuzzy Inference System (ANFIS). To verify the performance and accuracy of the developed diagnostic framework on GTE data, an ensemble of measurable gas path parameters has been generated by a high-fidelity GTE model under (a) diverse ambient conditions and control settings, (b) every possible combination of degradation symptoms, and (c) a broad range of signal to noise ratios. The results prove the competency of the developed framework in fault diagnostics and reveal the sensitivity of diagnostic results to measurement noise for different degradation symptoms.     

基于H∞方法的控制系统作动器最优控制仿真研究

在设计控制系统模型时,首先引入了有限差分法(FDM)离散化后的波动方程,然后基于H∞最优控制原理,检查闭环控制系统的稳定性和可探测性,对控制系统传感器和作动器的位置进行优化配置.通过计算闭环反馈系统的范数,最终得到了控制系统的最优控制算法.仿真结果表明,利用波动方程来优化控制系统传感器和作动器位置的算法是可行的,可广泛应用于飞控系统的设计中.     

硅半球深腔结构无损检测技术

半球深腔的加工质量是决定硅基MEMS半球陀螺精度的关键因素之一，及时检测半球深腔的形貌参数并将其反馈至加工过程，是确保高性能MEMS半球陀螺研制成功的重要措施。由于硅半球深腔的深度较大，台阶仪和光学显微成像系统无法对半球深腔的形貌特征进行有效测量。因此,需要将硅深腔结构剖开后采用扫描电镜(SEM)进行检测。这种检测方式时间周期长，且属于破坏性的样本检测，效率和测试精度都较低。提出以硅半球深腔为模具，利用PDMS铸模将硅半球深腔的结构尺寸和表面形貌转移到PDMS凸起的半球模型上，通过检测PDMS半球模型的尺寸结构和表面形貌，即可反推出硅半球深腔的尺寸特征。经实验验证，脱模后的PDMS模型可以准确地反映出半球深腔的尺寸信息，测量结果的不确定度小于5‰，有效解决了硅半球深腔无损检测的难题。     

低速大转矩永磁游标电机在发酵罐中的应用

采用秸秆生产丁醇时,为了达到高效率发酵,需要使发酵液中菌体分布均匀,所加物料需要及时搅拌。工业化生产丁醇的发酵罐尺寸较大,搅拌过程对驱动电机的输出转矩要求较高,因此高效率、小体积、低速大转矩的秸秆发酵搅拌电机对工业化发酵生产丁醇意义重大。设计了一种定转子永磁游标电机用于发酵液搅拌,并对电机的槽极数、电磁性能进行了具体的研究。制造样机并采用滞环控制实现了对液态发酵对象的快速响应,且实现了低能耗、高效率的发酵过程。     

某型教练机嵌入式训练系统顶层设计技术研究

本文通过对该型教练机现有航空电子系统构型、驾驶员操作程序、接口控制文件深入研究,结合未来功能扩展需求,给出了合理的系统构型分析、功能分配、数据流规划、原相关系统软件改动分析,在此基础上还设计出了嵌入式训练系统技术方案.依据方案研制的嵌入式训练系统原理样机通过系统动态试验、航电系统地面综合试验和飞机地面通电试验,证明系统...     

长板件数控加工技术的探索与研究

结合某型机板件在数控加工中的研制生产状况和存在的问题,论述了实现各种长板件类结构零件装夹定位、刀具及其参数、加工方案及程编策略.通过这些技术措施的实施,在一定程度上解决了在加工长板类零件装夹和定位时出现的零件变形、让刀效率低、质量不稳定等问题.