内并联型TBCC进气道方案设计及验证

提出了一种带可变几何泄流腔的内并联型涡轮基组合循环(TBCC)进气道设计方案.介绍了进气道的总体设计思路,给出了进气道的设计马赫数、转级马赫数及飞行轨迹,对不同来流条件下进气道的工作方式以及全马赫数范围进气道型面调整的安排进行了论述,确定了进气道主要气动参数与型面参数的选取原则.通过数值模拟和高速风洞试验的手段,对进气道设计方案的可行性进行了验证.数值模拟结果表明:当Ma₀≤2.5时,进气道的总压恢复系数均在0.8以上,当2.5<Ma₀≤4.5时,进气道的总压恢复系数均在0.3以上,符合进气道总体方案的要求;冲压模态下,冲压通道的出口马赫数均小于0.4,出口静压均大于0.5个标准大气压,均能满足冲压燃烧室的燃烧需求.风洞试验结果表明:模态转换过程中,进气道涡轮通道具有良好的进/发匹配特性,且进气道涡轮/冲压通道具有良好的相容性能.研究结果可为我国开展组合动力研究提供方案参考和技术储备.      

未来航空发动机控制技术的发展趋势

发动机控制系统在航空发动机系统中占有非常重要的地位,其性能的优劣直接影响到发动机及飞机的性能。本文针对未来航空发动机发展对控制系统的要求,分析了航空发动机控制技术的发展趋势。     

涡扇发动机故障诊断的快速原型设计

提出一种基于发动机基线模型的面向气路故障诊断的快速原型设计方法.考虑到基于模型的发动机全包线范围的故障诊断方法需要有较高精度的模型,选择合适的换算参数对已有的相似变换参数进行修正,建立适用于全包线的发动机基线模型,设计基于加权最小二乘算法的故障诊断模型,并将其写入至CompactRIO构建了发动机故障诊断的快速原型.通过对某型涡扇发动机试验表明:该种故障诊断的快速原型设计方法是有效的.      

基于气动热力模型的FADEC系统FHA方法

从适航规章对全权限数字发动机控制(full authority digital engine control,简称FADEC)系统的安全要求出发,结合功能危险分析(functional hazard assessment,简称FHA)的一般原则和FADEC系统的特点,得到了FADEC系统FHA的分析要素.根据分析要素中的工具与数据需求,将航空发动机气动热力模型用于可调放气活门(variable bleed valve,简称VBV)控制功能失效危险分析,结果表明:①该模型能够辅助确定FADEC系统功能失效的发动机影响;②FADEC系统功能危险的模型分析方法通过定量分析确定发动机影响的危险等级,为FHA提供直观的参考依据,可作为对专家经验的补充.      

Sensitivity Analysis for Safety Design Verification of General Aviation Reciprocating Aircraft Engine

This paper presents an application of global sensitivity analysis for system safety analysis of reciprocating aircraft engine. Compared with local sensitivity analysis results, global sensitivity analysis could provide more information on parameter interactions, which are significant in complex system safety analysis. First, a deterministic aviation reciprocating engine thermodynamics model is developed and parameters of interest are defined as random variables. Then, samples are generated by Monte Carlo method for the parameters used in engine model on the basis of definition of factor distribution. Eventually, results from engine model are generated and importance indices are calculated. Based on the analysis results, design is improved to satisfy the airworthiness requirements. The results reveal that by using global sensitivity analysis, the parameters could be ranked with respect to their importance, including first order indices and total sensitivity indices. By reducing the uncertainty of parameters and adjusting the range of inputs, safety criteria would be satisfied.     

液体火箭发动机涡轮泵转子弯扭耦合振动研究

为获得转子振动特性,针对液体火箭发动机涡轮泵转子系统建立了其在密封流体激振作用下的弯扭耦合动力学模型。通过数值仿真和试验研究了涡轮泵转子系统弯扭耦合振动的动力学特性,结果显示在密封流体激励作用下弯扭耦合振动的非线性特性显著。还研究了偏心距对涡轮泵转子系统弯扭耦合振动的影响。本研究可为液体火箭发动机涡轮泵转子的结构设计、诊断与维护提供可靠信息。     

某型号大推力火箭发动机试验推力测量不确定度评定

根据某型号大推力火箭发动机试验推力测量系统的工作原理和组成、计量标准量值传递关系和系统低温调试结果,确定推力测量系统的不确定度来源,通过进一步的误差分析并应用误差计算理论对系统不确定度进行评定,得出该系统测量不确定度作为推力测量准确性依据。     

基于SVM辨识的涡扇发动机全包线稳态控制方法

针对涡扇发动机全飞行包线范围稳态最优控制器的设计问题,首先根据不同飞行条件下发动机各工作状态的稳态“小偏差”线性模型,采用线性二次型调节器(LQR)分别设计得到相应的发动机最优线性控制器参数,然后将所得到的线性控制器用支持向量机方法进行非线性逼近,得到控制器参数的支持向量机辨识模型,以满足发动机全包线、全状态稳态控制的需要.支持向量机模型的输入为飞行高度、马赫数和稳态转速,输出为线性控制器参数.应用实例表明:该方法在全包线范围内对发动机最优稳态控制器的逼近误差均在2%以内,能较好满足控制精度要求.      

Designing method of acceleration and deceleration control schedule for variable cycle engine

Studies show that different geometries of a Variable Cycle Engine (VCE) can be adjusted during the transient stage of the engine operation to improve the engine performance. However, this improvement increases the complexity of the acceleration and deceleration control schedule. In order to resolve this problem, the Transient-state Reverse Method (TRM) is established in the present study based on the Steady-state Reverse Method (SRM) and the Virtual Power Extraction Method (VPEM). The state factors in the component-based engine performance models are replaced by variable geometry parameters to establish the TRM for a double bypass VCE. Obtained results are compared with the conventional component-based model from different aspects, including the accuracy and the convergence rate. The TRM is then employed to optimize the control schedule of a VCE. Obtained results show that the accuracy and the convergence rate of the proposed method are consistent with that of the conventional model. On the other hand, it is found that the new-model-optimized control schedules reduce the acceleration and deceleration time by 45% and 54%, respectively. Meanwhile, the surge margin of compressors, fuel–air ratio and the turbine inlet temperature maintained are within the acceptable criteria. It is concluded that the proposed TRM is a powerful method to design the acceleration and deceleration control schedule of the VCE.     

超燃冲压发动机准一维建模研究

在准一维流理论的基础上,考虑了燃料流量、截面变化、壁面摩擦、燃烧效率、化学反应放热等因素,应用影响系数法,构建了包括前体/进气道、隔离段、燃烧室、后体/尾喷管的超燃冲压发动机内流场准一维分析模型,可快速计算发动机参数沿轴向的变化以及出口值,便于发动机性能分析;以一个机体/推进一体化单模块飞行器为研究对象,通过与三维CFD数值模型进行对比。结果表明,准一维计算模型能较好地对超燃冲压发动机进行快速计算与分析,在超燃冲压发动机的初步研究阶段具有重要的应用价值。