基于粘附功的复合推进剂AP/基体界面损伤宏细观仿真

为研究复合推进剂AP/基体界面脱湿机理,建立了基于粘聚力界面模型的双尺度有限元损伤分析平台.为确定界面模型的输入参数,采用点滴法和Washburm毛细管上升法,分别测得基体与AP颗粒的接触角,再经Young's方程计算得到界面的粘附功.通过对不同体积分数下简化配方推进剂试件的拉伸试验结果与计算结果的对比显示,两者具有较...     

非离子表面活性剂在水流中的减阻机理

为探讨非离子表面活性剂的减阻机理,在实验确认表面活性剂APG水溶液（Alkyl Polyglucoside）具有湍流减阻功效的基础上,对其剪切粘度、应力松弛特性以及剪切双折射效应,使用锥板流变仪及流动双折射测试仪进行了实验研究。最大减阻率可达70％的APG水溶液,其剪切粘度在低剪切速率区域表现为牛顿流体特性,在大于临界剪切速率区域表现为“SIS”（Shear—Induced Structure）,呈现非牛顿流体特性;APG水溶液的剪切应力松弛特性与纯水基本相似,表明“SIS”并不具有粘弹性特性。由剪切双折射效应证实的的棒状胶束聚合结构和具有的较大拉伸粘度可认为是APG水溶液能够实现湍流减阻的主要原因。     

火场中电梯疏散失败的FTA分析与探讨

通过对火灾导致电梯疏散失败的故障树的建立与分析,计算了导致顶事件发生的最小割集与最小径集,以及影响顶事件发生的结构重要度和割集重要度。并由此提出了火灾情况下降低电梯运行风险,提高可靠性的相关措施。为火灾情况下利用电梯进行疏散的可靠性提供了参考依据。     

Modeling and identification of an electro-mechanical system: The LISA grabbing positioning and release mechanism case

In the frame of space missions, mechanisms often constitute critical systems whose functionality and performance need to be tested on ground before the mission launch. The LISA scientific space mission will detect gravitational waves by measuring the relative displacement of pairs of free-floating test masses set into geodesic motion onboard of three spacecrafts. Inside each satellite, the injection of the test masses from the caged configuration into the geodesic trajectory will be performed by the grabbing positioning and release mechanism. To provide a successful injection, the test masses must be dynamically released with a minimal residual velocity against adhesion with the holding device. A parameter that determines the test mass residual velocity is the quickness of the retraction of the holding device. The need arises then to characterize the dynamic response of the release mechanism in order to predict its behaviour in the in-flight conditions. Once a validated model of the mechanism is available, the compliance of the system to the tight requirement on the maximum allowed residual velocity of the test mass may be verified. Starting from an electro-mechanical model of the mechanism dynamics, this paper presents the results of the experimental identification of its relevant parameters.     

高精度大力矩补偿机构仿真模型

用于高稳定度卫星载荷扰动力矩补偿的补偿机构设计原理与力矩模式反作用轮类似,但具有输出力矩大、摩擦力矩大和饱和转速低的特点,且目前无针对性的仿真模型.迫于姿态控制系统的仿真需求,根据补偿机构的结构,合理简化的驱动控制电路的设计并结合反作用轮的建模方法,给出了详细的仿真模型.     

月球车释放对着陆器稳定性的影响

因基于摇臂式月球车释放机构在月球车释放时对着陆器的倾翻力矩较大,易使着陆器倾翻而导致整个探测任务失败,所以对月球车着陆释放时着陆器稳定性的研究尤为重要.将着陆器腿不等量压缩、月面坡度、低重力环境、释放加速度等因素进行参数化处理;应用D-H坐标法得到基于各参量的支撑多边形坐标以及着陆器和月球车的位姿方程,进而建立了月球车...     

发动机操作与悬摆式配重失效浅析

航空活塞发动机曲轴上装用的悬摆式配重组件承受着巨大的离心力及微动冲击力,工作条件极其恶劣,一旦失效,将直接导致发动机内部机件(如连杆、活塞、汽缸和凸轮轴等)出现严重的二次损伤,致使发动机停车。本文阐述了悬摆减振器减振原理和配重功用,分析了发动机操作与配重组件失效之间的内在联系,由此提出具体的预防措施。     

Linking Primordial to Solar and Galactic Composition

Evolution and composition of baryonic matter is influenced by the evolution of other forms of matter and energy in the universe. At the time of primordial nucleosynthesis the universal expansion and thus the decrease of the density and temperature of baryonic matter were controlled by leptons and photons. Non-baryonic dark matter initiated the formation of clusters and galaxies, and to this day, dark matter largely determines the dynamics and geometries of these baryonic structures and indirectly influences their chemical evolution. Chemical analyses and isotopic abundance measurements in the solar system established the composition in the protosolar cloud (PSC). The abundances of nuclear species in the PSC led to the discovery of the magic numbers and the nuclear shell model, and they allowed the identification of nucleosynthetic sites and processes. To this day, we know the abundances of the ∼300 stable and long-lived nuclides infinitely better in the PSC than in any other sample of matter in the universe. Thus, we know the exact composition of a Galactic sample of intermediate age, allowing us to check on theories of Galactic evolution before and after the formation of the solar system. This paper specifically discusses the nucleosynthesis in the early universe and the Galactic evolution during the last 5 Gyr.     

基于灵敏度分析的可调静叶调节机构运动精度优化

为提升高负荷多级轴流压气机静叶调节机构的运动精度，针对5级联调构型，梳理了37个对调节精度可能存在影响的 参数，提出了一种基于局部灵敏度分析的参数降维预处理优化方法。通过局部灵敏度分析认识各参数对调节精度的影响规律，甄 选重要参数，依靠自主优化程序与多体运动学软件联合的技术途径并采用SQP算法对机构进行优化：仅采用相对灵敏度影响最大 的9个参数进行优化时，调节精度达到0.4020°；采用剔除13个绝对灵敏度最小参数后的参数进行优化时，调节精度优化达到 0.2000°；而采用全部37个参数进行优化后，调节精度依然为0.2000°。结果表明：所提出的降维预处理优化方法能够在保证运动 精度的同时有效减小计算规模，联合优化的方式较传统虚拟样机优化具有更高的精度。     

空间望远镜成像镜调焦机构改进设计与分析

根据已有的研究工作，对成像镜调焦机构系统做了进一步改进，并对模型进行了环境影响分析和考虑接触时的受力分析．文中详细给出了设计的基本原理及设计方法，该机构通过电机驱动丝杠完成对成像镜的移动．由接触分析结果可以看出，考虑接触约束时所计算得到的结果比较符合实际情况，结构的强度满足要求．