EDA实验开发机设计

介绍了EDA实验开发机的总体设计方案，给出了各功能模块的描述方法，并对EDA实验开发机各模块的管脚锁定进行了较详细的说明。     

亚跨超风洞现代试验设计方法研究

开展了基于现代试验设计方法(MDOE)的亚跨超风洞试验研究,以八号标模尾翼为试验对象研究其气动特性,采用同时改变攻角-侧滑角的多变量方法,而不是传统的单变量(OFAT)方法进行试验。对自变量攻角和侧滑角进行试验设计(DOE),应用响应面法建模,用IV-最优方法对测量点分布进行设计。在FD-12亚跨超风洞完成了试验,并和传统的OFAT方法结果进行比较分析。结果表明:MDOE方法获得的数据和传统的OFAT方法的数据吻合很好;MDOE采集样点数减少了46%,吹风的时间比OFAT减少30%左右,提高了风洞试验效率,缩短了试验周期;MDOE试验方法可以给出设计空间内任意给定自变量对应的响应值及其置信区间。     

Azimuth selection for sea level measurements using geodetic GPS receivers

Based on analysis of Global Positioning System (GPS) multipath signals recorded by a geodetic GPS receiver, GPS Reflectometry (GPS-R) has demonstrated unique advantages in relation to sea level monitoring. Founded on multipath reflectometry theory, sea level changes can be measured by GPS-R through spectral analysis of recorded signal-to-noise ratio data. However, prior to estimating multipath parameters, it is necessary to define azimuth and elevation angle mask to ensure the reflecting zones are on water. Here, a method is presented to address azimuth selection, a topic currently under active development in the field of GPS-R. Data from three test sites: the Kachemak Bay GPS site PBAY in Alaska (USA), Friday Harbor GPS site SC02 in the San Juan Islands (USA), and Brest Harbor GPS site BRST in Brest (France) are analyzed. These sites are located in different multipath environments, from a rural coastal area to a busy harbor, and they experience different tidal ranges. Estimates by the GPS tide gauges at azimuths selected by the presented method are compared with measurements from physical tide gauges and acceptable correspondence found for all three sites.     

高职院校校外实践教学的探索与研究

通过分析和总结广州民航职业技术学院机务专业校外实践教学的经验，指出了高职院校校外实训教学开展应该注意的问题，提出了改进的措施，以促进学生实践技能的培养和提高，对高职院校开展校外实践教学具有一定的指导意义。     

两相脉冲爆轰发动机尾喷管的实验研究

为了提高脉冲爆轰发动机的推进性能,实验研究了12种不同构型尾喷管对火箭式两相脉冲爆轰发动机爆轰特性和推进性能的影响,并对各类尾喷管的增推原因进行分析。结果表明满填充工况下各类喷管内的爆轰特性不尽相同,收敛喷管可得到最大压力峰值;在满填充工况下频率为10Hz时12种喷管构型中拉伐尔喷管的推力增益最大,塞式收敛扩张喷管其次;拉伐尔喷管的出口面积比对推力增益有较大影响,但收敛段-扩张段长度比对推力增益影响甚微。     

刷式篦齿组合密封性能试验研究

与传统篦齿密封相比,刷式密封作为一种新型密封装置,密封性能改善明显。但在高压差条件下,刷式密封的封严性能提升效果不明显。为满足航空发动机高压差高性能需求,本文设计一种刷式篦齿组合密封来提升刷式密封的综合封严性能。刷式密封和刷式篦齿组合密封泄漏特性的仿真分析及对比试验结果表明,同工况条件下,刷式篦齿组合密封相比刷式密封,其泄漏量可减小（34.7%～68.5%）,封严性能更优异。因而,刷式篦齿组合密封为航空发动机高压差密封提供新的低成本途径,且结构紧凑、泄漏量低。     

Experimental investigation on ice-breaking performance of a novel plasma striker

Aircraft icing has long been a plague to aviation for its serious threat to flight safety.Recently, researches about a newly proposed deicing method based on Plasma Synthetic Jet Actuator(PSJA) have just started. To meet the requirements of in-flight deicing, structure of PSJA needs to be adjusted. This paper completed the detailed design and experimental validation of a novel plasma striker, which was a modified version of PSJA. Influences of mass of the moving part and rod shapes on the ice-br...     

RPC-MIP: the Mutual Impedance Probe of the Rosetta Plasma Consortium

The main objective of the Mutual Impedance Probe (MIP), part of the Rosetta Plasma Consortium (RPC), is to measure the electron density and temperature of Comet 67P/Churyumov-Gerasimenko’s coma, in particular inside the contact surface. Furthermore, MIP will determine the bulk velocity of the ionised outflowing atmosphere, define the spectral distribution of natural plasma waves, and monitor dust and gas activities around the nucleus. The MIP instrumentation consists of an electronics board for signal processing in the 7 kHz to 3.5 MHz range and a sensor unit of two receiving and two transmitting electrodes mounted on a 1-m long bar. In addition, the Langmuir probe of the RPC/LAP instrument that is at about 4 m from the MIP sensor can be used as a transmitter (in place of the MIP ones) and MIP as a receiver in order to have access to the density and temperature of plasmas at higher Debye lengths than those for which the MIP is originally designed.     

Gamma astrometric measurement experiment (GAME) – Science case

We report here on the science case of a concept for a satellite orbiting at 1 AU from the Sun and using a baffled Fizeau interferometer to look as close as possible to its limb. This configuration, and the need for looking nearby the Sun, is required for the main scientific driver of the mission, namely the measure of the γ parameter of the Parameterized Post-Newtonian formulation to the 10⁻⁶–10⁻⁷ level at least. This would lead to an accurate test of the General Theory of Relativity against other alternative theories of gravity, and set stringent constraints on some of the most significant issues of Astrophysics like those involving exotic forms of dark matter and dark energy. Exploiting the possibilities offered by the observation strategy, it is also possible to target other interesting scientific goals. One is, again, in the realm of General Relativity and aims at measuring the light deflection nearby the Giant Planets to detect asymmetric effects induced by their quadrupoles, predicted by GR but never measured so far. Others can be found in the observation of selected extrasolar systems where, e.g., the astrometric and photometric capabilities of GAME will help to improve on the knowledge of the brown-dwarf regime and on the search for exo-planets with the transit method, respectively.     

Experimental study on film cooling performance of imperfect holes

An experimental study is made to investigate the film cooling performance of imperfect holes due to in-hole blockage over a flat plate. A specifically pyramid-shaped element is used to simulate the in-hole blockage. Six in-hole blockage orientations (such as leading-inlet, leading-middle, leading-exit, trailing-inlet, trailing-middle and trailing-exit) and four blocking ratios (ranging from 0.1 to 0.4) are taken into considerations. Based on the experimental results, the influences of in-hole blockage on the film cooling effectiveness and discharge coefficient under typical blowing ratios are analyzed. It is confirmed that the in-hole blockage results in a reduction of discharge coefficient related to the perfect film cooling holes, especially for the leading-exit and trailing-inlet orientations with a big blocking ratio. However, in the view of film cooling effectiveness, the in-hole blockage shows complicated affecting roles. In general, except for the leading-exit orientation, the in-hole blockages produce detrimental influence on the film cooling effectiveness.