二维三轴编织复合材料压缩失效行为的细观有限元模拟

为研究典型二维三轴编织复合材料（2DTBC）的压缩破坏机理,建立了细观有限元模拟方法体系。提出了反映编织复合材料真实几何特性的单胞模型建模策略,根据Murakami-Ohno损伤理论建立了各向异性损伤模型来模拟纤维束中的损伤起始和扩展行为,通过引入波动系数描述了纤维束的起伏状态,并采用内聚力单元来模拟界面分层。在此基础上,分析得到了二维三轴编织复合材料在压缩载荷下的破坏过程,研究了压缩载荷下纤维束和界面层的损伤演化,探讨了纤维束波动对压缩性能的影响规律。通过与相关试验结果对比,该模型能够准确预测二维三轴编织复合材料在面内压缩载荷下的力学响应和主要失效行为,以及自由边效应。细观失效过程分析结果表明,二维三轴编织复合材料轴向压缩的破坏是由轴向纤维束的纤维压缩失效主导的;横向压缩破坏则是由偏轴纤维束的纤维压缩失效引起的。     

激光功率与底面状态对选区激光熔化球化的影响

为研究激光功率与底面状态对选区激光熔化熔池流动的影响,基于离散单元法建立了选区激光熔化铺粉模型,采用粒径分布与实验相符的马氏体时效钢粉末分别铺展到平坦底面和增材底面上,将计算获得的粉末分布导入到基于有限体积法建立的选区激光熔化熔池计算流体力学模型中,研究激光功率和基板底面粗糙度对熔池流动和熔道表面形貌的影响。采用激光单道扫描实验验证铺粉模型和选区激光熔化模型。结果表明：随着激光功率的降低,单位长度的球化数量增加;由于增材底面使熔池润湿性变差,同时又对熔池流动行为产生扰动,使得增材粗糙底面上熔道的球化数量增加。选区激光熔化铺粉模拟及激光单道扫描模拟结果与实验结果吻合较好。本研究可为选区激光熔化工艺中工艺参数的选择提供理论指导。     

一种开关磁阻电机无位置传感器控制效率优化策略

针对开关磁阻电机(SRM)的简化磁链法只能实现单相导通运行且导通区间固定的缺点,提出了一种结合固定关断角和自适应调节开通角的无位置传感器控制技术。利用曲线拟合关断位置磁链取代传统存储数据表,通过对比实时计算的动态磁链和曲线拟合的静态磁链,确定关断位置信号并估计转速和其他位置。考虑电机阻抗和电感的非线性特点,优化电感最小区域的开通角自调节模型确定导通区间。仿真结果验证了该方案的可行性和正确性,能够实现转子位置的间接检测,电机的运行效率得到进一步优化。     

基于双变量预测控制的表贴式永磁同步电机直接转矩控制系统

基于电压矢量幅值和相角为变量的表贴式永磁同步电机(SPMSM)定子磁链幅值和转矩表达式,给出了9个不同幅值和相角的备选电压矢量,采用预测控制计算得出施加不同电压矢量下一时刻的定子磁链幅值和转矩值,建立了基于磁链和转矩误差的目标函数,并选择使目标函数最小的电压矢量为作为下一时刻施加的最优电压矢量。仿真结果表明:在双变量预测控制下,SPMSM直接转矩控制系统运行良好,定子磁链轨迹为理想圆,磁链和转矩均符合控制要求,转速跟踪良好,定子电流波形正弦。进一步对比分析表明:与开关表和固定电压矢量选择策略相比,双变量预测控制能显著减小转矩和磁链脉动。与开关表相比,转矩脉动均方根误差降低了62.92%,磁链脉动均方根误差降低了45.05%,评价函数均值降低了60.30%;与固定电压矢量选择策略相比,转矩脉动均方根误差降低了22.40%,磁链脉动均方根误差降低了3.85%,评价函数均值降低了15.93%。     

Six sigma robust design optimization for thermal protection system of hypersonic vehicles based on successive response surface method

Lightweight design is important for the Thermal Protection System(TPS) of hypersonic vehicles in that it protects the inner structure from severe heating environment. However, due to the existence of uncertainties in material properties and geometry, it is imperative to incorporate uncertainty analysis into the design optimization to obtain reliable results. In this paper, a six sigma robust design optimization based on Successive Response Surface Method(SRSM) is established for the TPS to improve the reliability and robustness with considering the uncertainties. The uncertain parameters related to material properties and thicknesses of insulation layers are considered and characterized by random variables following normal distributions. By employing SRSM, the values of objective function and constraints are approximated by the response surfaces to reduce computational cost. The optimization is an iterative process with response surfaces updating to find the true optimal solution. The optimization of the nose cone of hypersonic vehicle cabin is provided as an example to illustrate the feasibility and effectiveness of the proposed method.     

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

High-fidelity trajectory optimization for aeroassisted vehicles using variable order pseudospectral method

In this study, the problem of time-optimal reconnaissance trajectory design for the aeroassisted vehicle is considered. Different from most works reported previously, we explore the feasibility of applying a high-order aeroassisted vehicle dynamic model to plan the optimal flight trajectory such that the gap between the simulated model and the real system can be narrowed. A highly-constrained optimal control model containing six-degree-of-freedom vehicle dynamics is established. To solve the formulated high-order trajectory planning model, a pipelined optimization strategy is illustrated. This approach is based on the variable order Radau pseudospectral method, indicating that the mesh grid used for discretizing the continuous system experiences several adaption iterations. Utilization of such a strategy can potentially smooth the flight trajectory and improve the algorithm convergence ability. Numerical simulations are reported to demonstrate some key features of the optimized flight trajectory. A number of comparative studies are also provided to verify the effectiveness of the applied method as well as the high-order trajectory planning model.     

基于试验气动力的弹性飞机舵面效率分析

基于非线性试验气动力和线性理论气动力对某飞机进行了气动导数和飞行载荷计算,分析了舵面操纵效率受气动力类型、飞行动压和迎角的影响,重点研究了舵面操纵效率、舵面操纵反效与翼面弹性载荷、弹性压差分布以及弹性气动压心之间的关系。研究表明：使用非线性试验气动力和线性理论气动力所分析得到的舵面效率具有较大的差别;受到结构弹性变形的影响,随着飞行动压的增加,舵面的操纵效率不断下降,副翼甚至会出现操纵反效现象;在使用非线性试验气动力进行分析时,飞行迎角对于舵面操纵效率具有较大的影响,这是在使用线性理论气动力进行分析时所不能考虑的。     

基于响应面的系统性能可靠性优化设计方法

提出了建立基于Logistic变换的性能可靠度与关键设计参数(DDP)之间函数关系的响应面方法以及性能可靠性优化设计模型。通过试验设计、一体化仿真、Logistic变换、多项式拟合、方差分析和模型检验等步骤,来构建系统性能可靠性响应面模型。并以性能可靠度为目标,性能设计参数可行域为约束进行设计优化。针对舵机案例,以性能模型和干扰模型为基础,通过仿真及回归分析,建立了性能可靠度与关键设计参数（Ce,Kp,J）的响应面模型。建立了舵机性能可靠性设计优化模型,对关键设计参数进行了优化。     

涡轮盘多轴低循环疲劳寿命可靠性分析

多轴低循环疲劳是航空发动机涡轮盘的主要失效模式,应用多轴疲劳寿命预测的等效应变模型和临界面模型对某涡轮盘中心孔的疲劳寿命进行了预测,并与试验寿命进行了对比,得出等效应变模型预测结果均偏于危险,并且误差较大,而临界面模型误差较小,尤其拉伸型破坏的SWT模型误差在10%以内。进一步选取SWT模型进行了涡轮盘的寿命可靠性分析,鉴于多轴疲劳试验复杂、费用高并缺少统计数据,利用现有单轴疲劳试验数据将疲劳性能参数表示为标准正态随机变量的函数,将SWT模型随机化建立多轴疲劳寿命概率模型,得到可靠度0.998 7的涡轮盘寿命,与试验估计给出的技术寿命较为接近。