材料非线性在折叠舵有限元计算中的运用

介绍了运用有限元方法对折叠舵进行了基于材料非线性的弹塑性分析。由于舵面上受到的载荷较大,超过材料的屈服强度,使接触区域材料进入塑性状态。如果进入塑性状态的范围过大,则结构将受到破坏,如果不采用弹塑性方法计算,而采用弹性方法计算,则舵的应力会更大,使舵面尖弦后缘点挠度变小,与试验值相比误差较大,不能忽略其材料非线性对变形计算的影响,本文考虑材料非线性的影响变形计算结果与实验结果吻合较好,因此,舵面变形最好使用弹塑性方法计算。     

移动电子设备相变热控单元热性能的数值仿真

采用相变材料(PCM,Phase Change Material)的热控制单元(TCU,Thermal Control Unit)可以很好地实现对可移动电子设备的热控制,避免设备过热而引起的热故障.建立了分析TCU热性能的二维数学模型,并进行了数值计算.结果表明:加肋和填充泡沫-PCM复合材料的设计方案可以显著提高TCU热性能,能很好地满足电子元件的工作要求.此外,还对加肋和填充泡沫-PCM提高TCU性能的效果进行了比较,结果表明:填充泡沫-PCM复合材料的方案更具优势.所得结论对移动电子设备TCU的设计和优化有一定的指导作用.     

碳酚醛-铝板中二维X射线热击波数值模拟

文章利用平面应变正交各向异性材料率相关性的弹塑性本构模型和各向同性材料理想弹塑性本构模型,采用有限元方法编写程序,对X射线辐照碳酚醛-铝板时诱导的热击波进行数值模拟,讨论了热击波的传播规律。结果表明,在1 keV的 X射线辐照下,X射线穿透极浅,材料表面发生气化现象,应力峰值较大;在3 keV的X射线辐照下,X射线穿透较深,热击波呈现双波结构,材料的层裂更明显。     

某探测器上火箭发动机热防护仿真与设计

根据某探测器的具体结构及工作条件,分析和计算探测器上火箭发动机的热环境参数.利用有限元法计算火箭发动机固壁辐射热流密度,依据热流边界条件设计热防护方案;利用有效发射率表征多层隔热材料隔热性能并进行温度场数值仿真.由于多层隔热材料性能参数的不易确定性,计算了参数在较大范围内的热防护效果.通过仿真计算验证热防护方案的有效性和可靠性,并分析影响热防护效果的主要因素;计算结果表明多层隔热材料的有效发射率是影响隔热性能最重要的因素,比热容、表面发射率、密度对热防护性能影响很小.      

引入材料参数的弯管中性层偏移解析模型

中性层偏移是表征管材弯曲内外侧不均匀变形程度的关键参数。基于弯管截面力矩平衡条件,建立了引入材料参数的管材弯曲变形中性层偏移解析模型,针对管材数控绕弯和压弯过程对所建模型从多个方面进行了评估,研究了不同几何和材料等管材本征参数下的管材弯曲中性层偏移规律。结果表明:应用于TA18钛管数控绕弯,发现所建解析模型与已有解析方法预测精度相当,但能考虑材料参数影响,且相较于有限元模拟,本文解析模型更接近实验结果;应用于A6063铝合金管和AZ31镁合金管压弯过程,并与Hasegawa解析方法相较,发现本文解析模型能够准确预测拉压不对称对压弯中性层偏移的影响;弯曲半径减小,弯管直径增大,中性层向弯曲内侧移动;拉压屈服强度比减小,厚向异性指数增大,中性层向弯曲内侧移动。     

VHF radio response of the near Earth space during solar activity growth in October, 2003

The analysis of observations of very high frequency radio noise intensity at the middle latitude on a frequency f = 500 MHz from 14th till 26th of October, 2003 is presented. These data are compared with the solar radio bursts in the range of frequencies 1–14 MHz registered by RAD2 receiver of the WAVES device installed on board the WIND spacecraft.     

纳米孔材料中辐射热传递的改进——扩散近似法计算

用可燃的烧蚀材料作为主动的承热层,用不可燃的多孔材料作为被动的隔热层,是当今一次性使用航天器最普通的一种热防护形式,然而对可重复使用的航天器来说,这种防热结构显然不适用.但是如果把烧蚀层改为金属薄壁或多层金属热防护系统,在不增加很多质量的情况下,能保证航天器主结构在允许的温度范围,则可能是一种很好的设计.在此情况下,隔...     

基于成绩评定法《工程材料》的教学改革

借鉴纽约洲立大学Metallurgy(冶金学)课程教学大纲,探讨高职高专院校工程材料课程的教学改革。提出要培养有创新能力的实用性人才须偏重实用技术理论,增强实践性教学环节,以平时为主的成绩评定法的教学改革思路。     

一种节约拉深材料的模具设计方法

介绍了节约材料的拉深模设计方法,较传统工艺方案用料减少10%。这对大批量生产节约用料,有较强的参考和借鉴价值。     

Magnetosphere response to the 2005 and 2006 extreme solar events as observed by the Cluster and Double Star spacecraft

The four identical Cluster spacecraft, launched in 2000, orbit the Earth in a tetrahedral configuration and on a highly eccentric polar orbit (4–19.6 R_E). This allows the crossing of critical layers that develop as a result of the interaction between the solar wind and the Earth’s magnetosphere. Since 2004 the Chinese Double Star TC-1 and TC-2 spacecraft, whose payload comprise also backup models of instruments developed by European scientists for Cluster, provided two additional points of measurement, on a larger scale: the Cluster and Double Star orbits are such that the spacecraft are almost in the same meridian, allowing conjugate studies. The Cluster and Double Star observations during the 2005 and 2006 extreme solar events are presented, showing uncommon plasma parameters values in the near-Earth solar wind and in the magnetosheath. These include solar wind velocities up to ∼900 km s⁻¹ during an ICME shock arrival, accompanied by a sudden increase in the density by a factor of ∼5 and followed by an enrichment in He⁺⁺ in the secondary front of the ICME. In the magnetosheath ion density values as high as 130 cm⁻³ were observed, and the plasma flow velocity there reached values even higher than the typical solar wind velocity. These resulted in unusual dayside magnetosphere compression, detection of penetrating high-energy particles in the magnetotail, and ring current development following several successive injections of energetic particles in the inner magnetosphere, which “washed out” the previously formed nose-like ion structures.