旋转对气膜冷却影响的大涡模拟

采用大涡模拟,考察了旋转影响气膜冷却的物理机制。参考实验模型,用带有30°倾斜圆柱孔的平板模拟涡轮转子叶片的吸力面,冷气出口雷诺数为1300,冷气和主流的吹风比为0.5,计算了静止和旋转数为0.2两种条件下的流动和换热,全面展示了旋转对平均流场、涡量、湍流结构和壁面温度分布的影响,并由此对实验现象进行了解释。结果表明,旋转使气膜孔下游的对转涡对产生不对称性;旋转引发的哥氏力使气膜冷却流场中的发夹型漩涡结构向高半径方向偏移,引起涡量分布的改变;旋转破坏了发夹涡的连续性,减少了对主流的卷吸和主流传递给冷气的热量,从而提高了冷却核心区的冷却效率,与实验中观察到的现象一致。     

绿色切削中的MQL技术

重点介绍了MQL(Minimal Quantities of Lubricant)技术的研究现状、实际应用、环境及经济性能评价以及尚待进一步解决的问题。指出MQL与刀具技术、低温风冷和水雾冷却技术的结合使用将是未来难加工材料高速切削领域中的主要潮流。     

Numerical investigation on adiabatic film cooling effectiveness and heat transfer coefficient for effusion cooling over a transverse corrugated surface

Three-dimensional numerical computations are conducted to investigate the effects of the blowing ratio and corrugation geometry on the adiabatic film cooling effectiveness as well as the heat transfer coefficient over a transverse corrugated surface. It is noticeable that the adiabatic wall temperature on the wavy valley of the transverse corrugated surface is relatively lower than that on the wavy peak. Surface corrugation has a relatively obvious influence on the laterally-averaged adiabatic film cooling effectiveness in the region where the effusion film layer is developed, but has little influence in the front region. Compared to a flat surface, the transverse corrugated sur-face produces a smaller adiabatic film cooling effectiveness and a higher heat transfer coefficient ratio. The effusion cooling difference between the flat and corrugated surfaces behaves more obvi-ously under a small aspect ratio of the wavy corrugation.     

三轮涡轮冷却器应用研究

本文通过对涡轮冷却器和飞机地面环控系统工作原理的分析，提出了将三轮涡轮冷却器用于飞机地面环控系统的设计方案。并给出了系统主要性能参数的计算结果。     

虚拟仪器技术的概念与实现

给出了虚拟仪器的概念 ,介绍了应用电子工作平台 (EWB)和虚拟仪器 (VI)技术来实现电子测量的方法     

Analytic estimation and numerical modeling of actively cooled thermal protection systems with nickel alloys

Actively cooled thermal protection system has great influence on the engine of a hypersonic vehicle, and it is significant to obtain the thermal and stress distribution in the system. So an analytic estimation and numerical modeling are performed in this paper to investigate the behavior of an actively cooled thermal protection system. The analytic estimation is based on the electric analogy method and finite element analysis（FEA） is applied to the numerical simulation. Temperature and stress distributions are obtained for the actively cooled channel walls with three kinds of nickel alloys with or with no thermal barrier coating（TBC）. The temperature of the channel wall with coating has no obvious difference from the one with no coating, but the stress with coating on the channel wall is much smaller than that with no coating. Inconel X-750 has the best characteristics among the three Ni-based materials due to its higher thermal conductivity, lower elasticity module and greater allowable stress. Analytic estimation and numerical modeling results are compared with each other and a reasonable agreement is obtained.     

涡轮叶顶间隙密封冷却综合特性评估方法

为了评估带气膜冷却涡轮叶顶间隙的密封和冷却综合特性,在强化传热综合因子中引入气膜冷却效率,推导出了密封冷却综合因子表达式.其物理含义为：主流在一定功率作用并喷入一定量冷气时,被评估的传热方式与基准传热方式传热性能比.数值模拟获得了动叶顶部隔板迷宫间隙气膜冷却和密封特性数据,利用该因子对密封冷却综合特性进行了评估.结果表明：在研究的吹风比内,迷宫结构的冷却效果相比于平叶顶间隙有所改进,随着吹风比减小,改进程度先增加后减小;密封效果只有在高吹风比时有所改进.密封冷却综合特性都得到了改进,吹风比越小,密封冷却综合特性越好.     

机载信息系统的应用研究及发展趋势初探

介绍了机载信息系统的技术现状,在民机上的不同应用架构及各种架构所具有的特点。从市场定位、新老机型应用、技术融合程度、人机工效等方面对机载信息系统的应用进行了研究,并根据机载系统产品发展的一般规律,对未来机载信息系统的发展趋势进行了初步预测。     

倾斜射流撞壁实验研究及液膜几何参数建模

倾斜射流撞壁在液体火箭发动机液膜冷却、射流撞壁雾化等领域具有广泛的应用。为了研究倾斜射流撞击壁面后形成的液膜的关键特征，开展单股圆柱射流撞击壁面的实验研究。从实验中研究各射流参数对液膜外形的影响规律，继而开展理论建模，获取液膜外形的关键几何参数表达式。实验研究发现随着射流倾角增大，液膜长度减小而宽度增大，随着射流孔径和射流速度增大液膜长度和宽度均增大这一定性规律。理论分析得到了液膜最大宽度位置与液膜对称面的夹角近似等于射流倾角α，液膜的长宽比近似等于1+cot α。通过进一步分析得到液膜宽度、最大宽度距撞击点的距离、液膜长度这几个液膜关键参数的表达式。建立的液膜几何参数表达式预测结果与实验结果的误差均在20%以内。     

喷雾液滴撞击液膜影响参数及流动机理分析

液滴撞击壁面是喷雾冷却中最常见的现象。使用计算流体力学软件中的Volume of Fluid （VOF）模型对液滴撞击壁面过程进行了数值模拟研究，研究了不同参数的液滴撞击壁面液膜过程的水花形态特点，针对水花高度和直径等参数进行了分析，通过运动间断理论和无量纲参数Re和We的变化分析了不同参数对液膜的流动特征和水花形态的影响及水花产生机理。结果表明：大液滴撞击液膜时能够改善液膜的流动状态；过大的液滴速度会产生大量飞溅及表面干涸；液滴撞击薄液膜时，液膜的流动性较好，当0.6<h*<1.2时，液膜的流动性不随液膜厚度改变。