基于电解扫掠成形原理的整体叶盘叶根加工方法

采用片状或管状阴极电解加工(ECM)后的整体叶盘由于加工运动、阴极形状等原因在叶根处会形成一定的加工残留,影响整体叶盘的加工精度。针对叶片电解加工后形成的叶根残留,开展去除叶根残留电解加工方法的研究,解决叶根电解加工的阴极结构、加工路径设计等难题。首先,分析了叶根的残留分布情况以及叶间通道的结构,采用了电解扫掠成形加工方案。其次,设计了阴极结构与加工路径,在阴极结构上采用了扇形流道并分析了电解液流速分布,通过增加引流槽、改变倾角等措施改善了流场;对阴极的运动路径进行了规划,利用专用仿真软件对阴极运动干涉与加工程序进行了检验;通过附加叶盘转动补偿了由于不同截面内叶间通道宽度与阴极刃口尺寸不一致给加工带来的不足。最后,制作了电解加工装置并通过试验对叶根电解加工方法进行了验证。试验结果表明,该加工方法有效去除了叶根残留,加工表面质量好,加工精度达到了要求。     

失速团动态演变特性试验

对一台单级低速轴流压气机进行了节流特性试验,通过周向布置动态压力传感器测得了节流过程的动态压力信号,结合时域、频域及极坐标可视化的分析方法,研究了节流过程的失速团动态演变特性.结果表明:失速先兆类型为模态波失速先兆,其传播频率约为40%转子转动频率;压气机进入失速初期349.5r时周向形成两个失速团,360r时两个失速团合并为单个失速团,压气机进入深度失速时单个失速团重新分裂并在410r时稳定为两个失速团;压气机退出失速的过程中,665r时两个失速团重新合并为单个失速团,674.5r时压气机退出失速.      

Microstructure evolution and mechanical anisotropy of M50 steel ball bearing rings during multi-stage hot forging

This study aimed to explore the evolution of flow lines and microstructures of M50-steel bearing ring and the anisotropy of its tensile mechanical properties after Multi-Stage Hot Forging (MSHF) and subsequent spheroidizing annealing (MSHFA). To this end, the present study mainly employed stereo microscopy, Optical Metallurgical Microscopy (OMM), Scanning Electron Microscopy (SEM), and Electron Backscatter Diffraction (EBSD) to characterize and analyze the workpiece at each processing stage of MSHF while performing microhardness measurement and uniaxial tensile experiment to test and analyze the mechanical properties of the workpiece. Macro-structure observation showed that the simulation results of flow lines at each stage were consistent with the experimental results. Microscopic observation showed that, after MSHF, deformation gradually became less significant along the outward radial direction of the bearing ring. After MSHFA, the microstructures of the bearing ring became uniform, whereas primary carbides did not dissolve. The mechanical properties were better in the axial direction (AD) than in the radial (RD) and circumferential directions (CD) after MSHF due to the smaller grain width. After MSHFA, the mechanical properties in the ADs and CDs were better than those in the RDs, which was due to the large cross-sectional area of carbides along the flow-line direction.     

Improvement of machining accuracy in EDCM by enhanced electrochemical reaming based on a non-metallic backing layer

Electrochemical Discharge Machining (ECDM) is potentially applicable for the fabrication of film-cooling holes. However, It is extremely difficult for the holes to achieve higher precision and machining quality owing to the working liquid diminish in the lateral machining gap. In this study, a non-metallic backing layer was proposed to overcome the diminish of working liquid, and the electrochemical reaming, as a post-processing method for ECDM, was used to further improve the machining accuracy and quality of the holes. First, the three-dimensional morphology of the melted pit of a paraffin backing layer was scanned to obtain the geometric parameters. Then, simulation analysis and experimental verification of auxiliary flushing by using the non-metallic backing layer were performed. The machining performance of the holes machined with electrochemical reaming based on non-metallic backing layer was confirmed by the observations of the surface topography of the hole wall and orifice, measurement of the orifice precision, and analysis of the element composition on the surface of the orifice wall. Finally, an optimum combination of machining parameters for electrochemical reaming is obtained through a process parameter optimization experiment.     

空间物体解体碎片云的长期演化建模与分析

空间碎片云由空间物体解体产生的大量空间碎片组成,由于其相对集中地分布在有限的空间内,将会对临近航天器产生较大的碰撞威胁。为了分析解体碎片云长期分布特点,文章首先利用数值积分方法对空间碎片云短期分布规律进行了研究;在此基础上,针对处于环状分布的碎片云,根据碎片所在的轨道高度和具有的面质比值,将碎片划分到不同分组,以每个组作为研究对象,建立了描述碎片云在大气阻力作用下的解析演化模型。模型避免了对单个解体碎片的运动状态进行积分,可大大降低对计算资源和计算时间的需求。考虑在高度为1422km 圆轨道上运行的物体,解体产生了1780个碎片,利用解析演化模型得到碎片云未来50年内的演化分布状态。数值结果表明,碎片云的峰值密度在解体物体轨道高度附近,并在大气阻力作用下向更大高度区间内扩散;较低高度区间内碎片密度具有先增加,然后在大气阻力作用下不断减少的特点。     

红外地球敏感器辐射强度在轨数据分析

为了给在轨卫星红外地球敏感器性能评估提供更多参考依据,通过对某颗长期在轨正常运行卫星所配置的红外地球敏感器辐射强度数据进行统计分析,给出辐射强度短期、中期和长期的变化规律,并分析造成这种变化的内在机理.分析结果表明,辐射强度短期与星下点纬度相关且呈周期变化;中期与季节相关且呈周期变化;长期主要与红外地球敏感器自身特性相关呈逐渐衰减趋势.该结果可以作为在轨红外辐射强度判读的依据.     

Modeling on mechanical behavior and damage evolution of single-lap bolted composite interference-fit joints under thermal effects

This paper reports the modeling method and outcomes of mechanical performance and damage evolution of single-lap bolted composite interference-fit joints under extreme temperatures. The anisotropic continuum damage model involving thermal effects is established on continuum damage mechanics which integrates the shear nonlinearity constitutive relations characterized by Romberg-Osgood equation. The temperature-induced modification of thermal strains and material properties is incorporated in stress-strain analysis, extended 3D failure criteria and exponential damage evolution rules. The proposed model is calibrated and employed to simulate behavior of composite joints in interference fitting, bolt preloading, thermal and bearing loading processes, during which the influence of interference-fit sizes, preload levels, laminate layups and service temperatures is thoroughly investigated. The predicated interfacial behavior, bearing response and failure modes are in good agreement with experimental tests. The numerical model is even capable of reflecting some non-intuitive experimental findings such as residual stress relaxation and matrix softening at elevated temperatures.     

Modeling high-speed cutting of SiCp/Al composites using a semi-phenomenologically based damage model

In this paper, we attempts to investigate cutting mechanisms in high-speed cutting of Al6061/SiC_p/15p composites using a semi-phenomenologically based damage model in the equivalent homogeneous material (EHM) framework. By combining macroscale EHM modeling and underlying microscale physical mechanisms, a feasible semi-phenomenological plastic model is proposed for prediction of cutting forces and chip morphology during high-speed turning Al6061/SiC_p/15p composites. This model incorporates the modified Weibull weakest-link effect to represent the strain-based damage evolution in large deformations. This proposed semi-phenomenological constitutive model is implemented by compiling material subroutines into cutting finite element (FE) codes. The effects of the critical shear stresses on chip formation that depend on the tool-chip frictional coefficient are accounted for in the cutting FE model. The chip formation mechanism affecting material removal behaviors during high-speed turning is further investigated. The capabilities of the proposed constitutive model are evaluated by comparing cutting forces and chip morphologies between experiments and simulations at different cutting speeds associated with strain rates. The EHM-based and microstructure-based models are further compared in both computational efficiency and accuracy. The simulation results show that the developed semi-phenomenological constitutive formalism and cutting model are promising and efficient tools for further investigation of dynamic mechanical and cutting behaviors of particle-reinforced composites with different volume fraction and particle size.     

通道曲面的柱面逼近方法及其在叶轮插铣中的应用

为了使叶轮粗加工后的通道表面与其设计曲面尽可能接近,将整体叶轮的定轴插铣理论模型概括为通道曲面的最大内接柱面优化问题。同时,为简化该问题的计算难度,将最大内接柱面的优化问题转化为柱面直母线方向和柱面准线的确定两个步骤。提出了确定内接柱面直母线方向的最小二乘模型与解算方法,在此基础上,将通道曲面沿柱面的直母线方向进行投影,通过相关曲线间的裁剪操作,获得了最大内接柱面的准线。以最大内接柱面的准线作为插铣加工时的边界曲线,以柱面直母线方向作为插铣加工时平头刀的轴线方向,给出了计算刀心位置和安全高度的迭代算法。最后通过数值算例验证了所提方法的正确性。该方法将有助于叶轮粗加工效率的提高,同时为叶轮的精加工预留较均匀的加工余量。     

航空薄壁零件加工变形的有限元分析

介绍了有限元法在薄壁件铣削加工中的应用,并运用ANSYS5.4有限元分析软件对典型薄壁框体零件的加工变形进行了分析计算,结果与实际加工情况相符,由此提出一种数控补偿方法来降低让刀误差,从而控制薄壁件的加工精度.