浮空器管材结构连接方式比较及拉伸强度分析

浮空器结构件如吊舱、过渡架及推进支架等多采用金属管材连接。目前,浮空器管材结构连接缺乏使用工况下极限值实测数据,材料及连接方式选择的理论支撑尚有不足。据此,对常用管材的不同连接方式进行比较及断裂分析。研究中铝合金和钛合金管材分别采用螺接及焊接的方式进行连接,测试样品的力学性能并结合仿真分析验证其断裂原因。结果表明:TA1钛合金管材采用焊接连接方式,相对螺接方式连接强度提高 87.9%;6061铝合金管材采用螺接连接方式,相对焊接方式连接强度提高 39.3%。2A12铝合金管材焊接连接强度优于螺接连接强度。同时,分析断裂原因发现,管材形变是影响焊缝连接强度的重要因素;应力集中易发生在管材端部连接处,导致端部焊缝发生断裂;管材形变会使母材断裂时伴有撕裂现象,进一步降低管材的最大连接强度。     

武汉地区电离层TEC和NmF2及板厚的季节变化

通过利用武汉电离层观测站(114.4°E,30.6°N)1980-1990年对E8T-Ⅱ卫星信标的法拉第旋转测量的TEC(电子浓度总含量)数据,以及由测高仪测量的1980-1990年间的f0F2(F2层临界频率)数据,研究了武汉地区TEC,NmF2(最大电子浓度)和板厚的季节变化,同时比较了IRI和武汉单站模式在预测NmF2季节性方面的有效性.武汉单站模式在预测NmF2季节性变化方面优于IRI模式.      

Effect of scavenge port angles on flow distribution and performance of swirl-loop scavenging in 2-stroke aircraft diesel engine

Swirl-Loop Scavenging (SLS) improves the performance of 2-stroke aircraft diesel engine because the involved swirl may not only benefit the scavenging process, but also facilitate the fuel atomization and combustion. The arrangement of scavenge port angles greatly influences in-cylinder flow distribution and swirl intensity, as well as the performance of the SLS engine. However, the mechanism of the effect and visualization experiment are rarely mentioned in the literature. To further investigate the SLS, Particle Image Velocimetry (PIV) experiment and Computational Fluid Dynamics (CFD) simulation are adopted to obtain its swirl distribution characteristics, and the effect of port angles on scavenging performance is discussed based on engine fired cycle simulation. The results illustrate that Reynolds Stress Turbulence model is accurate enough for in-cylinder flow simulation. Tangential and axial velocity distribution of the flow, as well as the scavenging performance, are mainly determined by geometric scavenge port angles α_geom and β_geom. For reinforcement of scavenging on cross-sections and meridian planes, α_geom value of 27° and β_geom value of 60° are preferred, under which the scavenging efficiency reaches as high as 73.7%. Excessive swirl intensity has a negative effect on SLS performance, which should be controlled to a proper extent.     

典型二元高超声速进气道与侧压式进气道的性能比较

在相同的约束条件下运用高超声速进气道已有的相关设计方法设计了两类典型的二元进气道与侧压式进气道,利用数值模拟手段对两类进气道的流场结构和总体性能开展了对比研究.研究发现,二元进气道出口流场畸变较小,流场均匀性优于侧压式进气道;二元进气道流量系数对飞行马赫数的敏感程度远高于侧压式进气道;设计点,二元进气道性能优于侧压式进气道.非设计点,尤其在接力状态下,侧压式进气道性能突出;侧压式进气道阻力特性优于二元进气道,而二元进气道的前体升力则高于侧压式进气道.      

红外反射材料In(Sn)2O3(ITO)的微波吸收性能

测试7.7vol%和15.8vol%In(Sn)2O3(ITO)/石蜡在2~18GHz的介电谱。测定10vol%和20vol%In(Sn)2O3(ITO)/环氧树脂在2~8GHz的反射率。结果显示,ITO材料具有很好的介电损耗。当涂层厚度d=3mm时,两种涂层分别在4.51GHz和6.27GHz有-10.5dB和-14dB的反射率。理论值显示,15.8vol%ITO/石蜡复合材料在4.56~11GHz的反射率低于-10dB,有好的吸波性能。同时分析ITO的介电损耗机理。     

单一压力容器镍氢电池组几何参数对其温度场的影响

 针对实际空间用单一压力容器(IPV)镍氢电池组的传热特点,建立其瞬态热分析的数学物理仿真模型。通过设计改变电池组几何参数,包括电池组底板厚度、套筒高度和厚度,采用有限差分法,对比模拟研究电池组在飞船实际运行条件下几何参数对其温度场的影响。结果表明：套筒厚度对电池组温度场的影响最为敏感,增大套筒厚度可明显缩短电池组热系统达到平衡态的响应时间;其次是套筒高度;改变底板厚度对电池组温度场变化影响不明显。该研究为镍氢电池组的结构优化和热控制研究提供理论基础。     

基于预测脱靶量的远程拦截速度增益导引

 针对拦截器使用耗尽关机固体燃料发动机的情况,设计了大气层外目标拦截的速度增益导引方法。导引律中根据Lambert导引确定指令推力方向初值,利用剩余速度增量信息,计算惯性速度增益下的预测脱靶量,使用Kepler轨道摄动方程计算消除脱靶量所需的速度增益修正,根据惯性速度增益和速度增益修正之和确定指令推力方向。给出了一种计及J2项引力摄动影响的滑行段弹道预测半解析方法,减少导引律运算量,降低导引方法误差;导引律中引入了剩余速度增量测量环节,增强了导引精度对推进系统参数的鲁棒性。与传统的通用能量管理（GEM）导引相比,采用该导引律拦截远程目标时指令推力方向平稳、变化范围小,脱靶量降低了两个数量级。     

数据融合的对流层天顶延迟估计方法

为提高对流层天顶延迟(Zenith tropospheric delay，ZTD)的估计性能，提出了基于数据融合的ZTD估计方法。估计干延迟采用Saastamoinen模型，估计湿延迟采用Askne模型，地表气象测量设备提供给两模型所需的气压、温度以及水汽压，Askne模型所需的加权温度、温度变化率和湿度变化率由全球气压和温度2w(Global pressure and temperature 2w，GPT2w)模型提供。当气象测量设备不可用时，上述所有气象参数均来自于GPT2w模型。利用国际GPS服务(International GPS service, IGS)提供的数据进行验证，结果表明：当地表测量设备存在时，所提方法较Saastamoinen模型提高了8mm；当全部气象参数来自GPT2w时，本方法较GPT2w+Saastamoinen模型提高了8.1mm；对于季节分明的测站，误差趋势同样具备季节性；对于海拔高和气候干燥的的测站，估计误差较小。     

Ionospheric parameters in the European sector during the magnetic storm of August 25–26, 2018

Variations of ionospheric parameters Total Electron Content (TEC) by GNSS, critical frequency (foF2) by vertical sounding and electron density (Ne) by low-altitude satellite were studied at high, mid and low latitudes of the European sector during the magnetic storm of August 25–26, 2018. During the main phase of the storm the ionospheric F2-layer was under the positive disturbance at mid and low latitudes. Then the transition from the positive to negative ΔfoF2 values occurred at all latitudes. The recovery phase was characterized by negative ionospheric disturbance at all latitudes. This is due to the decrease of thermospheric O/N2 ratio during the recovery phase of the storm. The intense Es layers screened the reflections from the F2-layer on August 26th at high and at low latitudes but at different times. Some blackouts occurred due to the high absorption level at high latitudes. In general, foF2 and TEC data were highly correlated. The major Ne changes were at the low latitudes. In general, Ne data confirmed the ionospheric dynamics revealed with foF2 and TEC.     

Satellite capture as a restricted 2 + 2 body problem

A restricted 2?+?2 body problem is proposed as a possible mechanism to explain the capture of small bodies by a planet. In particular, we consider two primaries revolving in a circular mutual orbit and two small bodies of equal mass, neither of which affects the motion of the primaries. If the small bodies are temporarily captured in the Hill sphere of the smaller primary, they may get close enough to each other to exchange energy in such a way that one of them becomes permanently captured. Numerical simulations show that capture is possible for both prograde and retrograde orbits.