雷暴云准静电场和夜间低电离层的电离

用点电荷模型计算雷暴云突然放电后形成的准静电后形成的准静电场随高度的分布，以E/N（E的电场大小，N为大气密度）为输入参量，在一定条件下，对Boltzmann方程数值求解，计算电离层电子数密度的扰动。计算结果表明，在约70-90km之间，在约放电后的10ms内，准静电场大于中性大气的击穿电场，将引起大气的雪崩电离，从而引起夜间低电离层电子密度的显著增加，但这种电子密度的增加是暂的，在很短的时期内就恢复到平静时的水平，恢复时间随高度的变化而不同。     

The characteristics of sharp (small-scale) boundaries of solar wind plasma and magnetic field structures

We investigate properties of large (>20%) and sharp (<10 min) solar wind ion flux changes using INTERBALL-1 and WIND plasma and magnetic field measurements from 1996 to 1999. These ion flux changes are the boundaries of small-scale and middle-scale solar wind structures. We describe the behavior of the solar wind velocity, temperature and interplanetary magnetic field (IMF) during these sudden flux changes. Many of the largest ion flux changes occur during periods when the solar wind velocity is nearly constant, so these are mainly plasma density changes. The IMF magnitude and direction changes at these events can be either large or small. For about 55% of the ion flux changes, the sum of the thermal and magnetic pressure are in balance across the boundary. In many of the other cases, the thermal pressure change is significantly more than the magnetic pressure change. We also attempted to classify the types of discontinuities observed.     

非平稳信号的双重中值容错平滑算法

平滑是消除或削弱测量数据随机误差时常用的数据处理手段。文章建立了一组新的非平稳数据序列容错平滑算法，其采用两阶段两次滑动中值与滑动均值平滑组合，实现了数据简化与平滑的统一。理论分析和仿真计算结果证实，算法可有效避免斑点型异常数据的不利影响，有效削弱随机误差的影响，改进数据处理精度和数据处理结果可靠性。     

一般硬化材料弹塑性旋转盘的变分解法

首先在小弹塑性范围内用应变的奇次四项式相当精确地拟合一般硬化材料的拉伸曲线;再在体积不变条件下用弹性位移场的已知模态和一待定幅值构成弹塑性位移场;最后用势能原理确定该幅值而得到封闭解。     

研究用现场数据估计系统可靠性参数置信区间

研究用元部件现场信息估计系统可靠性参数,如系统可靠度、可靠寿命等区间估计问题。文中提出了一种新的估计方法——替换百分点法,并运用Monte Carlo数字仿真对估计的置信度和精度进行了分析,研究结果表明此方法具有工程应用价值。     

基于参数化模型和遗传算法的复合材料加筋壁板结构选型优化研究

针对复合材料加筋壁板的结构优化选型问题,采用辅助层压板和添加极小弹性模量材料的复合材料加筋壁板有限元建模方法,应用PATRAN/NASTRAN的参数化建模功能和遗传算法相结合的复合材料加筋壁板的优化方法,对5种复合材料结构形式进行了从2000N/mm到6000N/mm压缩载荷下的结构优化分析。结果表明,当载荷小于4500N/mm时,最有效的加筋壁板结构型式为J型;当压缩载荷大于4500N/mm时,最有效的加筋壁板结构型式为I型。     

Modeling novel methodologies for unmanned aerial systems–Applications to the UAS-S4 Ehecatl and the UAS-S45 Bálaam

The rising demand for Unmanned Aerial Systems(UASs) to perform tasks in hostile environments has emphasized the need for their simulation models for the preliminary evaluations of their missions. The efficiency of the UAS model is directly related to its capacity to estimate its flight dynamics with minimum computational resources. The literature describes several techniques to estimate accurate aircraft flight dynamics. Most of them are based on system identification. This paper presents an alternative methodology to obtain complete model of the S4 and S45 unmanned aerial systems. The UAS-S4 and the UAS-S45 models were divided into four sub-models, each corresponding to a specific discipline: aerodynamics, propulsion, mass and inertia, and actuator. The‘‘aerodynamic" sub-model was built using the Fderivatives in-house code, which is an improvement of the classical DATCOM procedure. The ‘‘propulsion" sub-model was obtained by coupling a two-stroke engine model based on the ideal Otto cycle and a Blade Element Theory(BET) analysis of the propeller. The ‘‘mass and the inertia" sub-model was designed utilizing the Raymer and DATCOM methodologies. A sub-model of an actuator using servomotor characteristics was employed to complete the model. The total model was then checked by validation of each submodel with numerical and experimental data. The results indicate that the obtained model was accurate and could be used to design a flight simulator.     

AADL在航天器控制系统设计中的应用研究

以某型号航天器为例提出了一种使用体系结构分析和设计语言(AADL,architecture analysis & design language)分层次建模的方法,建立控制系统软件及软件与硬件之间的交互模型.采用状态自动机方式描述串口通信协议,以便分析模型.     

Investigating gamma-ray burst data reduction techniques with Swift’s instruments

The amount of data on gamma-ray bursts (GRBs) and the detected afterglows observed by the Swift satellite contributed significantly to the understanding of the phenomenon. The behavior of the early afterglow rises some interesting questions. With the early afterglow localizations of gamma-ray burst positions made by Swift, the clear delimitation of the prompt phase and the afterglow is not so obvious any more. There are hints of a canonical X-ray afterglow lightcurve with segments of different slopes. Not all bursts necessarily show all the segments. It is important to see if the prompt phase and the afterglow has the same origin or they stem from different parts of the progenitor system. We will combine the of gamma-ray burst data from BAT and XRT and compare the extrapolated gamma-ray flux to the X-ray in a sample of bursts and find that there is a good agreement between the two measurements. This indicates that the physical process shaping burst and the early afterglow are the same.     

数字化技术在叶轮研制中的应用

本文通过分析归纳建立了一种叶轮数字化建模方法，并利用该方法成功实现了某型叶轮三维模型创建，同时也根据该数字化模型实现了模具数字化设计及其数控加工。