一种减少失速保护虚警率的混合滤波方法

针对飞机失速保护设计过程中易出现虚警的情况,提出一种基于FIR和传统滤波器相结合的混合滤波方法。结合飞机本体的运动特征,对参与失速保护逻辑运算的两个重要参数,即侧向加速度和迎角信号进行频率分析,基于信号的特征设计混合滤波器,然后采用Simulink滤波工具箱设计滤波器对信号进行滤波处理。仿真结果表明该方法能够减少虚警率的发生,特别是大背景噪声下的虚警率能够得到较好抑制,验证了滤波器设计正确性,从而提高失速保护功能对适航条款符合性。该滤波器设计方法,不但可以有效解决本文提到的问题,对于其他涉及信号处理的系统设计同样具有借鉴意义。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

异步点火相位对二冲程发动机爆震燃烧的影响

为了了解异步点火相位对二冲程航空活塞发动机燃用煤油时的爆震影响问题,使用Fire软件建立了发动机燃烧室的计算模型,并通过试验验证了该模型,研究了异步点火相位对发动机缸内燃烧以及火焰面密度分布、爆震强度的影响等.结果表明:在转速为5000r/min、全负荷工况、混合气当量比为11、点火能量为3564mJ条件下,当其中一个火花塞点火时刻固定在上止点前曲轴转角为29° ,另一个火花塞相对其分别提前曲轴转角为1°,3°,5°时点火,随着双火花塞异步点火相位差的增大,缸内平均压力、放热率及累积放热量均呈现减小的趋势,两个火花塞附近的湍动能增大,火焰传播速度加快,火焰发展期缩短,爆震强度表征物的浓度逐步减小,二冲程煤油发动机爆震发生的倾向减小.      

S形进气道锤击波荷载特性分析

利用基于改进的延迟分离涡模拟（IDDES）方法,对亚声速和超声速来流条件下某S形模型进气道进行了非定常计算,研究了发动机喘振所产生的瞬时高压波形对锤击波传播规律的影响.结果表明:锤击波产生后沿进气道迅速向前传播,运动过程中锤击波的运动速度基本保持不变,但强度不断增强.同时受气流离心力的影响,S形进气道弯曲段半径较大一侧壁面受到的锤击波气动荷载值更大.发动机喘振所产生的瞬时高压的加载梯度增加使得锤击波传播速度及强度增强,而压力卸载方式对锤击波强度的影响不明显.在亚声速和超声速来流条件下,增加瞬时高压峰值均使得锤击波荷载强度显著增强,并近似符合二次函数分布规律,而且超声速来流条件下锤击波强度较亚声速来流更强.      

基于响应面法的短距/垂直起降飞机近地面升力损失

建立了短距/垂直起降(S/VTOL)飞机近地面升力损失的流场计算模型.通过数值模拟得出特定升力布局的飞机近地面状态各工况的升力损失.采用响应面法获得了飞机升力损失关于喷管落压比（NPR）、来流速度及飞机高度的2阶响应曲面函数及显著影响飞机升力损失的关键因素.并分析了喷管落压比、来流速度及飞机高度对飞机升力损失的交互影响作用,优化得出给定工况范围内升力损失最小的工作点.研究表明:仅考虑单因素影响时,升力损失随高度、落压比的增大而减小,随来流速度的增大而增大;考虑两因素交互作用时,高度与落压比及来流速度与落压比对升力损失存在交互影响,而高度与来流速度对升力损失无交互影响;优化获得的升力损失最小的工作点是飞机距地面高度为9D（D为喷管直径）、喷飞机高度为3、来流速度为0m/s,此时的升力损失为1.3%.      

球形点火腔对脉冲爆震DDT过程影响的数值研究

为了减小脉冲爆震发动机PDE（pulse detonation engine）单次循环时间,缩短爆燃向爆震转变DDT（deflagration to detonation transition）距离是关键.为此,提出了一种在头部添加球形点火腔的新型爆震管道结构设计方案,并采用丙烷和空气为可爆混合物,通过对新型爆震管DDT过程的二维数值模拟,研究其对DDT距离以及DDT时间的影响.数值模拟结果表明,头部采用球形点火腔后,点火腔中的压缩波经过多次反射后,能够在爆震管中更快地促使爆震波形成,DDT距离大大缩短;当球形点火腔直径为1.5倍等直爆震管直径时,相对于常规等直管爆震管结构,其DDT距离和过程时间分别减少了14%和16.26%.      

液体火箭发动机充液导管流固耦合动力学特性

为了深入研究流固耦合（FSI）作用对液体火箭发动机充液导管频率特性的影响,采用传递矩阵法(TMM)建立了空间导管流固耦合动力学计算模型.针对真实发动机导管开展了传递矩阵模型与传统基于附加质量的有限元(FEM)（非耦合）模型仿真计算以及模态试验验证,比较了管径、壁厚等结构参数对导管流固耦合作用的影响.结果表明:在流固耦合作用下,导管各阶谐振频率减小、而对应的流体振荡与结构振动幅值增大.管径对导管低阶频率特性的影响较壁厚对其影响更大.对于该算例,当管径大于设计值30%后,耦合作用引起的1阶频率误差高于10%,此时流固耦合不能忽略;而壁厚对1阶谐振频率的影响则小于8%.      

电离层色散对DS/FH-BPSK信号解调性能影响

相位连续的DS/FH(Direct Sequence/Frequency Hopping,直接序列/跳频)扩频信号的扩频带宽比直扩信号更宽,在电离层的非线性相位以及跳频频点变化这两者的共同作用下,该信号的BPSK(Binary Phase Shift Keying,二相相移键控)解调性能明显恶化。依据随机变量概率分布的数学规律,推导得到了在背景电离层色散条件和跳频频点均匀分布前提下,某种DS/FH卫星测控信号的引导信号和长周期信号BPSK误码率的变化规律,并在特定信号参数条件下进行了误码率仿真。     

深空探测器无线电干涉测量开源数据处理系统构建及试验

为更好地开展深空无线电干涉测量试验,基于DiFX(Distributed FX,分布式FX型相关处理)、SPICE(Spacecraft Planet Instrument Camera-matrix Events,航天器行星仪器照相机矩阵事件)、HOPS(Haystack Observatory Postprocessing System,Haystack克天文台后处理系统)及AIPS(Astronomical Image Processing System,天文图像处理系统)等开源软件,搭建了一套可用于深空探测器信号相关处理的无线电干涉测量数据处理系统。首先介绍了该系统的整体架构及组成,然后介绍了系统各组成模块的功能及工作原理,最后利用该系统对嫦娥三号着陆器开展了观测试验,并对观测数据进行了处理。试验结果表明,该系统能成功实现深空航天器信号的相关处理、条纹拟合,以及时延解算等功能,有望为我国嫦娥五号任务及火星探测任务数据处理提供支持。