基于N-S方程的悬停旋翼桨叶气动干扰数值模拟

采用基于N-S方程的CFD方法,通过计算前后平行放置的双翼和三翼的干扰流场,对悬停状态旋翼桨叶之间的气动干扰机理进行了数值探讨;在此基础上,进行了2种桨叶片数、2种桨距及2种桨尖马赫数情况的旋翼悬停流场对比计算,模拟它们对旋翼气动性能和桨叶间气动干扰作用的影响,得到一些与工程实际吻合的现象和结论。     

近距鸭翼高度对鸭翼－前掠翼布局纵向气动特性影响的实验研究

前掠翼布局由于其潜在的优越性,在未来战斗机的研究设计中将占有日益重要的地位.本文通过风洞测力实验,研究了近距鸭翼相对于前掠主机翼的高度对布局纵向气动性能的影响.实验结果表明:随着主机翼前掠角的增大,近距鸭翼布置高度逐渐增加可获得较好的气动特性.     

高速客车模型气动特性实验研究

介绍了高速客运列车模型气动特性在低速风洞中测量结果.试验模型由头车、中间车、尾车模型组成,且头、尾车互换位置.试验风速为80~300km/h,风向角为0°.同时还进行受电弓接触压力测量.试验结果表明:不同头车和尾车组合,对高速客车的气动阻力有很大影响.整流罩和受电弓使列车空气阻力明显增加.     

Advanced ensemble modeling method for space object state prediction accounting for uncertainty in atmospheric density

For objects in the low Earth orbit region, uncertainty in atmospheric density estimation is an important source of orbit prediction error, which is critical for space traffic management activities such as the satellite conjunction analysis. This paper investigates the evolution of orbit error distribution in the presence of atmospheric density uncertainties, which are modeled using probabilistic machine learning techniques. The recently proposed “HASDM-ML,” “CHAMP-ML,” and “MSIS-UQ” machine learning models for density estimation (Licata and Mehta, 2022b; Licata et al., 2022b) are used in this work. The investigation is convoluted because of the spatial and temporal correlation of the atmospheric density values. We develop several Monte Carlo methods, each capturing a different spatiotemporal density correlation, to study the effects of density uncertainty on orbit uncertainty propagation. However, Monte Carlo analysis is computationally expensive, so a faster method based on the Kalman filtering technique for orbit uncertainty propagation is also explored. It is difficult to translate the uncertainty in atmospheric density to the uncertainty in orbital states under a standard extended Kalman filter or unscented Kalman filter framework. This work uses the so-called “consider covariance sigma point (CCSP)” filter that can account for the density uncertainties during orbit propagation. As a test-bed for validation purposes, a comparison between CCSP and Monte Carlo methods of orbit uncertainty propagation is carried out. Finally, using the HASDM-ML, CHAMP-ML, and MSIS-UQ density models, we propose an ensemble approach for orbit uncertainty quantification for four different space weather conditions.     

典型激波针减阻降热特性及流动机理

为研究激波针对超/高超声速钝头飞行器进行减阻降热的相关特性,采用数值模拟方法对6种典型激波针构型的流动特征开展系统研究。给出了激波针长度、来流马赫数对流动特征的影响规律,并对其形成机理进行了探讨。结果显示:马赫数较低时,头部有扰流物的5种激波针在回流区即将分裂时减阻率最大;马赫数较高时,减阻率在回流区分裂前后出现局部峰值,但最大减阻率将出现在回流区分裂后更长的激波针长度下。马赫数为3时,6种构型减阻率达最大时的相对长度在0.8~1.2之间,相比而言,球型、半球型和双锥型的减阻效果最好,最大减阻率为45%~50%;圆锥型最差,为20%~25%,明显低于头部有扰流物的构型。相同的激波针长度下,头部有扰流物构型的减阻率随马赫数增大而增大,圆锥型则相反。流场回流区、分离激波、弓形激波、局部膨胀流动等导致的压力分布变化是构型整体阻力变化的主要成因。      

涡轮叶片内部微小V肋-凹陷涡复合冷却流动与传热数值模拟

为强化航空发动机涡轮叶片内冷通道传热性能,针对带有微小V肋-凹陷涡高效复合冷却结构矩形通道,采用Abe Kondoh Nagano （AKN） k-ε湍流模型数值模拟研究了肋高与凹陷深度组合对流动传热特性的影响机理。结果表明,当凹陷深度一定,复合结构的强化换热效果随肋高增加而增加,3mm肋高复合结构的传热相比纯凹陷提高了87.1%;当肋高一定,传热随凹陷深度增加先增强后基本保持不变,6mm深凹陷复合结构相比纯V肋提高了52.8%。通过在凹陷上游布置V肋,增强了越过V肋冲入凹陷内流体的湍动能,从而使凹陷前部回流区减小;同时来自微小V肋的涡流与凹陷内部的涡流相互作用,增强了整个流场的动量和热量输运,使通道换热均匀,并相较纯凹陷或纯V肋结构均有显著提升。     

顺逆流向喷流干扰下二体分离气动力风洞实验研究及前体轴向力特性

本文概述了具有顺，逆流向喷流干扰的二体分离气动力风洞实验技术研究。对有喷流干扰引起的前体轴向气动力特性，作了简单的介绍。最后对有顺、逆流向喷流干扰的前体底部流动模型作了定性的描绘，可供理论研究时参考。     

“大涡破碎”的紊流减阻实验研究

本文对当今国外曾提出的紊流表面摩擦减阻新概念——“大涡破碎”(LEBU)进行了初步的风洞实验探索。将具有对称流线型剖面的二元小肋,沿垂直于气流的方向安置在平板表面的紊流附面层内某一高度处,收到了不同程度的减阻效果。实验中分别考察了小肋的安置位置L,安置高度H,迎角θ及相对厚度b等参数对减阻效果的不同影响。从紊流附面层涡结构的观点出发,提出紊流的“细化”作用是小肋对平扳减阻的根本原因,并认为改善紊流附面层的速度型是研究紊流减阻的一种手段。实验使用自制的高灵敏度摩擦天平,测得的减阻效果与Ludwieg—Tillman公式的计算结果基本一致。     

失速改出伞阻力特征面积估算方法

研究了高平尾布局飞机的气动特性。使用失速改出伞是飞机改出深失速的重要途径,但如何确定失速改出伞的关键参数(阻力面积等)却没有现成的方法。以ARJ21-700飞机为例,分别使用公式分析法、类比法综合估算出失速改出伞的关键参数,通过模型自由飞和模拟仿真分析验证其具有足够效能将飞机改出深失速状态。形成了一套新机失速改出伞的设计方法和关键数据图表,可供其他型号飞机失速改出伞的设计研制使用。     

A novel environmental control system based on membrane dehumidification

This paper conducts a simulation study of a novel aircraft environmental control system based on membrane dehumidification(MD-ECS),and compares the system with the up-to-date four-wheel high pressure de-water system(4WHPDW-ECS).Mathematical models for the two systems are established,and a system simulation using a numerical technique is performed to analyze and compare the cooling performance of the two systems.Simulation results show that the cooling capacity of MD-ECS is much higher than that of 4WHPDW-ECS under the same working conditions,indicating that the novel system is theoretically feasible and promising.The effects of the sweep ratio of the membrane dehumidifier on the dehumidification and cooling performance of the system is also investigated.