Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

气固两相透平叶片冲蚀特性的气动试验研究

在自行研制风洞中先后对应用较广的MCrAlY叶片涂层和2Cr12Mo-5叶片合金、钢丸表面强化试件在不同气流速度、颗粒冲角、颗粒性状、颗粒粒度的条件下进行了气动冲蚀试验。试验结果表明,无论是涂层还是合金,冲蚀率均随冲蚀颗粒的累积质量呈线性变化;由对比可知,其它条件相同的情况下,涂层在广泛的冲角范围内较合金的冲蚀率更小,表面的"烧结"特征,能减小叶片的冲蚀率;表面呈多棱的石英砂颗粒对试件的冲蚀程度强于带突圆球状的催化剂颗粒;在该试验范围内,相同材质的颗粒,粒度愈大,对试件的冲蚀率愈大;钢丸表面强化工艺兼有防冲蚀的能力。试验结果将为优化叶片选材、简化叶片维修技术、降低叶片维修成本提供有益的参考。     

旋翼桨叶动力学设计技术

桨叶动力学设计,其实质是求解非线性高维动力学逆问题的具体实施。本文较全面地阐述了这方面的进展情况,提出了切实可行、有效实用的数值方法。     

高转速风扇叶片外物撞击损伤的定量评价方法

外物撞击是造成航空发动机风扇叶片变形、损伤甚至断裂的主要因素。针对外物撞击持续时间短、瞬间载荷大、损伤影 响因素多，难以进行定量损伤评价的问题，提出基于叶片损伤参数α的叶片损伤定量评价方法。以发动机风扇叶片受冰撞为例， 采用非接触叶尖计时测量方法，对叶片撞击产生的叶尖位移进行监测分析，验证了该方法的可行性。采用瞬态动力学分析方法对 叶片经受撞击过程进行全流程仿真模拟，并采用正交试验法定量研究了外物撞击过程中的撞击速度、叶片转速、撞击位置3种因 素对叶片损伤参数α的影响，拟合回归方程并绘制了这3种因素的3D响应曲面图，得到各因素的影响权重。结果表明：冰块速度 与撞击位置同时下降时，叶片损伤弱化效果显著。该方法可为大型风扇叶片抗外物打击性能设计和在役健康监测提供理论支撑。     

自然通风和蒸发冷却在新疆建筑应用的数值分析

为了使新疆和田地区夏季在经济性合理前提下使室内通风环境满足人体热舒适要求。利用蒸发冷却技术将室外空气处理后送入室内，通过数值模拟分析得出在夏季室内负荷最大时刻采用机械辅助式自然通风，使得室温能够雏持在26-8℃，风速为0．6m/s，基本满足人体热舒适要求。在室外温度适宜的过渡季节采用Trombe墙和太阳能烟囱复合的自然通风系统，建筑太阳能烟囱的经济高度为10m。     

Lift coefficient prediction at high angle of attack using recurrent neural network

In this paper, identification of dynamic stall effect of rotor blade is considered. Recurrent Neural Networks have the ability to identify the nonlinear dynamical systems from training data. This paper describes the use of recurrent neural networks for predicting the coefficient of lift (C_Z) at high angle of attack. In our approach, the coefficient of lift (C_Z) obtained from the experimental results (wind tunnel data) at different mean angle of attack θ_mean is used to train the recurrent neural network. Then the recurrent neural network prediction is compared with experimental ONERA OA212 airfoil data. The time and space complexity required to predict C_Z in the proposed method is less and it is easy to incorporate in any commercially available rotor code.     

主/从动式组合旋翼悬停状态气动特性分析

针对传统直升机构型中主旋翼旋转时产生的扭矩需要尾翼或是反向旋转的共轴旋翼加以抵消,从而造成能量浪费的问题,以将主旋翼旋转时产生的扭矩转化为升力为出发点,提出了一种主旋翼带动下方无动力旋翼旋转的主/从动式组合旋翼气动布局构型。通过动量叶素理论以及CFD数值模拟中的多重参考系法,对主/从动式组合旋翼悬停状态的气动特性进行了初步分析,结果表明,此构型中的下方从动旋翼利用上方主动旋翼的扭矩产生了额外10%的升力,同时下方从动旋翼在上方主动旋翼引流的有利干扰下升力系数提高了35%。     

钛合金转子叶片系列焊机的研制及应用

针对各种新型航空发动机钛合金转子叶片阻尼台毗邻面耐磨性提高的迫切需求,研制成功JQGP-80型系列真空充氩高频感应钎焊设备,结合国产化材料及焊接工艺的全面突破,解决了钛合金叶片阻尼凸台磨损问题,为多种重点型号研制的顺利进行提供了强有力的硬件保障。     

考虑重力的风机叶片水平加载测试方法

在风电叶片三维有限元参数模型中引入了重力产生的附加载荷,仿真计算了风电叶片水平加载方式的静载荷测试中附加载荷产生的水平方向的耦合位移,分析了耦合位移对测试过程中理论计算结果的影响;由于重力的叠加效应,测试中某些截面实际施加的等效载荷可能远超叶片设计的目标测试载荷,建议联合有限元分析,优化叶片安装角度和加载力方向的方法,降低叶片局部截面实际施加等效载荷的过载峰值。     

基于叶尖定时的叶片耦合振动参数辨识与仿真

为了实时掌握叶片振动情况、预防故障发生,目前最常用的非接触振动测量方法是基于单自由度模型的叶尖定时法,但当叶片耦合振动时2个振动峰相隔很近,该方法无法同时识别出其振动参数。采用基于2自由度模型的曲线拟合方法,得到叶片耦合振动2个峰的初始相位等参数,用相位遍历法辨识出叶片的振动阶次和频率。结果表明:采用基于2自由度模型的曲线拟合方法提高了叶片耦合振动参数辨识的精度,辨识了相邻2个峰的振动参数。辨识振动与仿真参数设置基本一致。