全文获取类型
收费全文 | 559篇 |
免费 | 393篇 |
国内免费 | 84篇 |
专业分类
航空 | 774篇 |
航天技术 | 36篇 |
综合类 | 45篇 |
航天 | 181篇 |
出版年
2024年 | 3篇 |
2023年 | 20篇 |
2022年 | 38篇 |
2021年 | 37篇 |
2020年 | 28篇 |
2019年 | 34篇 |
2018年 | 25篇 |
2017年 | 57篇 |
2016年 | 63篇 |
2015年 | 33篇 |
2014年 | 63篇 |
2013年 | 45篇 |
2012年 | 45篇 |
2011年 | 47篇 |
2010年 | 30篇 |
2009年 | 21篇 |
2008年 | 20篇 |
2007年 | 35篇 |
2006年 | 22篇 |
2005年 | 24篇 |
2004年 | 32篇 |
2003年 | 24篇 |
2002年 | 30篇 |
2001年 | 25篇 |
2000年 | 25篇 |
1999年 | 24篇 |
1998年 | 24篇 |
1997年 | 29篇 |
1996年 | 30篇 |
1995年 | 16篇 |
1994年 | 11篇 |
1993年 | 14篇 |
1992年 | 20篇 |
1991年 | 3篇 |
1990年 | 12篇 |
1989年 | 11篇 |
1988年 | 10篇 |
1987年 | 6篇 |
排序方式: 共有1036条查询结果,搜索用时 15 毫秒
341.
飞机蒙皮划痕问题已成为飞机维护中最为突出的结构问题之一。本文结合波音公司发布的维护/维修方案和服务通告SB-737-53A1262、SB-737-53A1289,对飞机维修中划痕损伤的问题进行探讨。 相似文献
342.
343.
344.
对适航当局的法规文件中“重要修理”定义的各个要素进行了全面和深入的研究探讨,同时对“影响适航指令的符合性”的含义进行了分析和解释,为航空公司和维修企业进行重要修理和一般修理的判定提供了参考。 相似文献
345.
针对民用飞机蒙皮常见的凹坑损伤,利用Nastran/Patran软件总结归纳了修理时补片厚度、大小、形状等主要修理工艺参数的变化对修理质量的影响,进而优化修理方案。 相似文献
346.
This paper presents an experimental study of a novel K-Cor sandwich structure rein- forced with partially-cured Z-pins. The influence of pultrusion processing parameters on Z-pins characteristics was studied and the effect of Z-pins on mechanical properties was disclosed. Differential scanning calorimetry (DSC) and optical microscopy (OM) methods were employed to determine the curing degree of as-prepared Z-pins and observe the implanted Z-pins in the K-Cor structure. These partially-cured Z-pins were treated with a stronger bonding link between face sheets and the foam core by means of a hot-press process, thereby decreasing burrs and cracking defects when the Z-pins were implanted into the Rohacell foam core. The results of the out-of-plane tensile tests and the climbing drum peel (CDP) tests showed that K-Cor structures exhibited superior mechanical performance as compared to X-Cor and blank foam core. The observed results of failure modes revealed that an effective bonding link between the foam core and face sheets that was provided from partially-cured Z-pins contributed to the enhanced mechan- ical performances of K-Cor sandwich structures. 相似文献
347.
348.
根据热传导、复合材料力学和固化动力学理论,采用基于偏微分方程的强耦合多物理场有限元方
法,计算在F650 双马来酰亚胺树脂建议温度周期下直升机复合材料桨叶固化过程中温度、固化度、固化度反应
速率和内应力变化历程。通过仿真结果对温度周期进行优化调整,改善工艺过程。计算结果表明:桨叶中树脂
固化反应同步度高,交联反应产热量少;调整后的加热周期与建议加热周期相比,最高加热温度由460 K 降低
为393 K,但固化度由0. 1 增加到1 的反应时间只由25 min 增加为30 min,固化反应速率峰值从1. 35×10-3 / s
降低为1. 15×10-3 / s,PMI(聚甲基丙烯酰亚胺,Polymethacrylimide)泡沫的Von Mises 热应力最大值从0. 82 MPa
降低为0. 482 MPa。
相似文献
349.
根据FAA颁发的AASR的要求,2010年12月20日以后,波音737-系列飞机的维护计划中需包含损伤容限的基本检查要求。波音依据AASR的要求对需要进行损伤容限分析的结构修理的批准实施了新的方法。新方法的实施,导致波音对结构修理类型分类法方法和批准方式的改变。 相似文献
350.
为了验证热辐射通量理论计算方法对推进剂的适用性,采用热辐射计测试了三种推进剂在外部火烧试验中的热辐射通量最大值和平均值,并根据样品燃烧时间计算了样品的热辐射通量。三种推进剂的热辐射通量的测量平均值为2.87kW/m2,2.65kW/m2和3.44kW/m2,理论计算值为4.06kW/m2,7.62kW/m2和3.67kW/m2。结果表明:当样品燃烧时间大于5s时,热辐射通量的测试平均值与理论计算值基本一致;当燃烧时间小于5s时,由于理论计算公式中设定的燃烧热转变为辐射热的比例(0.33)大于实际转化率,导致热辐射通量的理论计算值偏大,因此建议用热辐射计测量样品的热辐射通量。 相似文献