Reliability design optimization of composite structures based on PSO together with FEA

The present work aims to develop a method for reliability-based optimum design of composite structures. A procedure combining particle swarm optimization (PSO) and finite element analysis (FEA) has been proposed. Numerical examples for the reliability design optimization (RDO) of a laminate and a composite cylindrical shell are worked out to demonstrate the effectiveness of the method. Then a design for composite pressure vessels is studied. The advantages and necessity of RDO over the conventional equi-strength design are addressed. Examples show that the proposed method has good stability and is efficient in dealing with the probabilistic optimal design of composite structures. It may serve as an effective tool to optimize other complicated structures with uncertainties.     

Composite control method for stabilizing spacecraft attitude in terms of Rodrigues parameters

In this paper, the attitude stabilization problem of a rigid spacecraft described by Rodrigues parameters is investigated via a composite control strategy, which combines a feedback control law designed by a finite time control technique with a feedforward compensator based on a linear disturbance observer (DOB) method. By choosing a suitable coordinate transformation, the spacecraft dynamics can be divided into three second-order subsystems. Each subsystem includes a certain part and an uncertain part. By using the finite time control technique, a continuous finite time controller is designed for the certain part. The uncertain part is considered to be a lumped disturbance, which is estimated by a DOB, and a corresponding feedforward design is then implemented to compensate the disturbance. Simulation results are employed to confirm the effectiveness of the proposed approach.     

关于某型飞机客舱舷窗组件设计的分析与研究

复合材料有着良好的可设计性和减重性能,客舱舷窗组件也在积极探索应用复合材料的可能。详细分析和探讨了某型飞机客舱舷窗组件的设计。     

航天用复合材料结构高温极限承载能力试验方法

针对航天飞行器飞行特点,本文给出两种基于破坏时间的承载能力试验方法,可以获得结构在不同飞行温度和时间下的承载能力。能够充分发挥材料在传热过程中的高温承载能力,降低结构防热质量。     

复合材料微波胶接修补技术的研究及应用

根据微波快速固化、均匀制热的机理,研制开发了全新的复合材料微波快速胶接修复设备,并进行了修补试验.试验结果证明,该技术完全满足飞机结构件的修复要求,且显著地缩短了修复时间.     

中继卫星S/Ka双频地面站天线共用跟踪接收机

论述了Ka频段圆波导TE11和TE21模自跟踪体制和S频段正十字排列四喇叭自跟踪体制共用两信道自跟踪接收机问题.导出了来波及地面天线S频段和、差信道极化特性引起的角误差电压的交叉耦合系数公式.还可以进一步使S/Ka两个频段共用一套能跟踪（直接序列）扩频信号源的伪单脉冲（单信道单脉冲）自跟踪接收机.     

Reduction of vibration by periodically stitched sandwich panel

This work reveals that the addition of periodically distributed stitches to sandwich structure enables a significant reduction of vibration in stop-band and this new functionality is systematically investigated. Firstly, a finite element model which is capable of taking into consideration the three layers of the sandwich as well as the stitches is developed. The diagram of dispersion is calculated by applying Floquet-Bloch theorem to the boundaries of unit cell. With properly chosen properties of stitches, a stop-band for flexural wave is observed. This stop-band is further confirmed by the forced response of a large stitched sandwich panel under point excitation. The level of vibration in the stop-band is significantly reduced. The influence of the stitch rigidity and density on upper and lower limits of stop-band is also examined, which confirms that stitched sandwich can be tuned to mitigate vibration in a certain frequency band with appropriate stitch properties. These investigations have demonstrated the potential application of stitched sandwich in the area of vibration reduction.     

Wetting behavior of AgCu-4.5Ti filler reinforced by carbon nanotubes on C/C composite

The effect of Carbon Nanotubes (CNTs) content on the wettability of AgCu-4.5Ti + x CNTs (wt%) composite filler alloys on C/C composite was investigated. The results show that the added CNTs reacted with element Ti in the filler and produced the dispersed fine in situ synthesized TiC particles, which increased the consumption of element Ti and provided the nucleus for the growth of Ti-Cu compounds simultaneously. The above effects of introducing CNTs, inhibited the formation of Ti-Cu compounds, also changed the distribution of compounds, which dramatically influenced the interfacial microstructure and characteristics of wetting behavior. The increase of CNTs content refined and dispersed coarse Ti-Cu compounds, decreased the initial spreading temperature, and improved the wettability, but high content of CNTs (more than 0.3wt%) decreased the wettability of the filler alloy. The wetting interfacial microstructure of corresponding composite filler alloys were analyzed by Scanning Electron Microscope (SEM), Energy Dispersive X-ray Spectrometer (EDS) and Transmission Electron Microscope (TEM), which consisted of TiC, TiCu, TiCu₂ and TiCu₄ compound. The typical wetting behavior of AgCu-4.5Ti + 0.3wt% CNTs composite filler on C/C composite was divided into four stages. The effect mechanism of CNTs content on the wetting behavior was proposed.     

大尺寸CFRP固体火箭发动机壳体湿法缠绕用树脂配方研制

针对大尺寸炭纤维增强复合材料（CFRP）固体火箭发动机壳体的制备要求,研制了一种具 有良好粘度－温度及粘度－时间特性的炭纤维复合材料湿法缠绕成型树脂配方A。采用差示 扫描量热法（DSC）、傅立叶红外光谱（FT-IR）等分析技术对树脂基体的固化反应进行了系 统地研究,并测试了配方的粘度、力学性能及容器爆破强度。结果表明,该树脂配方A的反应 表观活化能为41.71 kJ／moL,室温下粘度低（≤0.5390 Pa·s）,适用期较长 （＞48 h ） ,不仅完全满足大尺寸CFRP固体火箭发动机壳体的湿法缠绕成型工艺要求,而且其树脂基体 及其炭纤维复合材料表现出优良的力学性能。炭纤维复合材料界面粘接良好,缠绕的
Φ150 mm容器的PV／W均大于48 km,纤维强度转化率达到89.0％以上。
     

硼酸酯键合剂在丁羟四组元推进剂中作用机理研究

采用反相气相色谱仪测试了BA-5键合剂,RDX,AP和HTPB-TDI胶片的表面酸碱性参数,并估算出各组分之间的界面相互作用焓。结果表明ΔHBA-RDX和ΔHBA-AP均显著大于ΔHBA-HTPB,证实键合剂BA-5与RDX,AP作用力远大于与粘合剂作用力,能在混合过程中优先迁移吸附在RDX,AP颗粒表面,并产生强烈吸附。采用电子能谱仪定性表征了RDX,AP从HTPB中吸附BA-5的情况。结果表明:随着电子束加速电压降低,测试厚度变小,AP样品中硼原子含量增加,证实BA-5是吸附在AP的表面。结合组分基团活性分析,阐述了BA-5键合剂的作用机理。