全文获取类型
收费全文 | 335篇 |
免费 | 61篇 |
国内免费 | 54篇 |
专业分类
航空 | 265篇 |
航天技术 | 53篇 |
综合类 | 94篇 |
航天 | 38篇 |
出版年
2023年 | 5篇 |
2022年 | 11篇 |
2021年 | 16篇 |
2020年 | 12篇 |
2019年 | 10篇 |
2018年 | 14篇 |
2017年 | 20篇 |
2016年 | 23篇 |
2015年 | 17篇 |
2014年 | 24篇 |
2013年 | 18篇 |
2012年 | 17篇 |
2011年 | 21篇 |
2010年 | 21篇 |
2009年 | 21篇 |
2008年 | 16篇 |
2007年 | 19篇 |
2006年 | 19篇 |
2005年 | 15篇 |
2004年 | 13篇 |
2003年 | 8篇 |
2002年 | 7篇 |
2001年 | 13篇 |
2000年 | 7篇 |
1999年 | 6篇 |
1998年 | 6篇 |
1997年 | 8篇 |
1996年 | 11篇 |
1995年 | 3篇 |
1994年 | 5篇 |
1993年 | 25篇 |
1992年 | 5篇 |
1991年 | 4篇 |
1990年 | 5篇 |
1989年 | 3篇 |
1988年 | 1篇 |
1987年 | 1篇 |
排序方式: 共有450条查询结果,搜索用时 375 毫秒
101.
This paper seeks to outline the temperature effect on the buckling properties of ultra-thin-walled lenticular collapsible composite tube(LCCT) subjected to axial compression.The buckling tests of the LCCT specimens subjected to axial compression were carried out on INSTRON-500 N servo-hydraulic machine in dry state and at the temperatures of 25 C, 100 C and 80 C. The load–displacement curves and buckling initiation loads were measured and the buckling initiation mechanism was discussed from experimental observations. Experiments show that the buckling initiation load, on average, is only about 2.2% greater at the low temperature of 80 C than at the room temperature of 25 C due to the material hardening, demonstrating an insignificant increase in the buckling initiation load, whereas it is about 19.5% lower at the high temperature of 100 C than at the room temperature owing to the material softening, implying a significant decrease in the buckling initiation load. The failure mode of the LCCT in axial compression tests at three different temperatures can be reckoned to be characteristic of the buckling initiation and propagation around the central region until rupture. The finite element(FE) model is presented to simulate the buckling initiation mechanism based on the eigenvalue-based methodology. Good correlation between experimental and numerical results is achieved. 相似文献
102.
103.
104.
长焦镜头能够采集位置更远的图像,而长焦镜头成像的特殊性对传统相机标定方法提出了挑战。针对这一问题,阐述了一种基于平行光管和二维旋转平台的相机内参标定方法。长焦相机被架设在二维旋转平台上,对放置在平行光管内的透过式棋盘格成像。通过旋转二维平台,改变相机的位置,可以得到不同位置下清晰的棋盘格图像。采集了棋盘格格点的像素坐标以及二维平台的角度数据,建立了合适的模型,优化求解出了长焦相机的内参参数,实现了实验室内对长焦镜头的标定。由模型计算得到的重投影棋盘格角点的图像坐标与在实际图像中检测到的棋盘格角点坐标相比,平均误差约为0.5个像素,这验证了算法的可行性。 相似文献
105.
为了探索引压管腔在动态压力校准中各校准方法的一致性与数据准确性,确立了以简单直管形式引压管腔开展动态特性校准的研究。采用理论和仿真的手段分析并建立了引压管腔模型,理论模型和仿真结果一致性极高。利用3种正弦压力校准装置对同一引压管腔进行了动态校准组合试验,结果表明:3种校准方法所得的动态特性与理论分析趋势一致,对于引压管腔基频的校准各试验之间偏差小于0.55%,但与基频理论值最大偏差为-3.17%。该研究将会为未来引压管腔结构设计和动态特性的补偿修正提供了一定参考依据。 相似文献
106.
介绍了埋管式冷板的设计及3种制造成形工艺:胶接、焊接和铸造,并分析了3种成形工艺的优缺点及对埋管式冷板散热性能的影响。采用有限元软件FloEFD对相同参数条件下同一模型不同成形工艺的埋管式冷板的散热性能进行了仿真对比分析,仿真结果表明:当其它条件相同时,不同成形工艺对埋管式冷板的散热性能具有一定的影响,基板与铜管之间的热阻越小,冷板的散热性能越好。 相似文献
107.
何贤泽 《中国空间科学技术》1990,10(4):53-57
根据通信卫星用行波管放大器的研制经验,论述了残存气体和材料的气化微粒对它的危害,讨论了消除这种危害的方法,列举了国内外的典型事例. 相似文献
108.
109.
110.