全文获取类型
收费全文 | 281篇 |
免费 | 74篇 |
国内免费 | 61篇 |
专业分类
航空 | 309篇 |
航天技术 | 31篇 |
综合类 | 47篇 |
航天 | 29篇 |
出版年
2024年 | 2篇 |
2023年 | 4篇 |
2022年 | 12篇 |
2021年 | 20篇 |
2020年 | 14篇 |
2019年 | 9篇 |
2018年 | 7篇 |
2017年 | 21篇 |
2016年 | 40篇 |
2015年 | 10篇 |
2014年 | 9篇 |
2013年 | 10篇 |
2012年 | 23篇 |
2011年 | 18篇 |
2010年 | 16篇 |
2009年 | 14篇 |
2008年 | 16篇 |
2007年 | 22篇 |
2006年 | 16篇 |
2005年 | 9篇 |
2004年 | 15篇 |
2003年 | 13篇 |
2002年 | 17篇 |
2001年 | 12篇 |
2000年 | 13篇 |
1999年 | 7篇 |
1998年 | 19篇 |
1997年 | 6篇 |
1996年 | 5篇 |
1995年 | 4篇 |
1994年 | 2篇 |
1993年 | 4篇 |
1991年 | 5篇 |
1990年 | 1篇 |
1988年 | 1篇 |
排序方式: 共有416条查询结果,搜索用时 31 毫秒
71.
《中国航空学报》2021,34(4):540-567
Continuous fiber reinforced SiC ceramic matrix composites (FRCMCs-SiC) are currently the preferred material for hot section components, safety–critical components and braking components (in the aerospace, energy, transportation) with high value, and have triggered the demand for machining. However, the high brittleness, anisotropy, and heterogeneity of materials bring great challenges to machining, due to high mechanical and thermal loads, severe tool wear, and poor machining quality. With the increasing demand of FRCMCs-SiC parts, high-quality and high-efficient machining has become a hot issue. This review paper provides a detailed literature survey on the machining of FRCMCs-SiC. The material removal mechanism, defect form, and interfacial mechanical properties of FRCMCs-SiC were summarized. The machining processes of FRCMCs-SiC were introduced, and their respective advantages and disadvantages were compared. Given the low machinability (high hardness, high brittleness, anisotropy, and heterogeneity) of FRCMCs-SiC, preliminary experiments have proved that ultrasonic-assisted machining and laser-assisted machining have shown unique advantages in reducing force and tool wear, improving machining quality and machining efficiency. The machined surface integrity was discussed, the influence of process parameters on the machined surface quality was analyzed, and the machining defects of FRCMCs-SiC were summarized. But for FRCMCs-SiC, the existing quantitative evaluation of the machined surface integrity was weak and unsystematic. 相似文献
72.
DLC涂层硬质合金微钻的制备及其切削性能 总被引:1,自引:0,他引:1
在硬质合金微型刀具加工高硅铝合金等难加工材料时,通过采用改进的热丝CVD装置开展了DLC涂层硬质合金微钻制备工艺优化,得到了最优沉积工艺,并配合高速加工高硅铝合金(Si15%)材料微小孔钻削性能对比试验,分析了刀具的磨损机理.结果表明:两步预处理方法适合复杂形状硬质合金衬底的预处理方法.钻削高硅铝合金时,DLC涂层具有低摩擦系数和高耐磨损特性,同等切削条件下,涂层微钻的切削寿命比未涂层硬质合金微钻提高了10倍. 相似文献
73.
由于钛合金和印刷电路板的难加工性使得微小孔的加工精度和表面质量难以保证,刀具技术成为提高加工效率的主要障碍。本文应用3种不同涂层钻头对钛合金和印刷电路板进行微小孔钻削对比试验,研究了进给速度与切削力和扭矩的关系,分析了刀具的磨损特征以及孔的表面质量和孔入口处的毛刺情况。结果表明:钻削印刷电路板的临界进给速度为1 591.2 mm/m in,涂层对钻削力和扭矩的影响不明显;类金钢石(DLC)涂层硬质合金钻头比普通硬质合金钻头和T iC涂层硬质合金钻头更适合加工钛合金材料微小孔。 相似文献
74.
为减小碳纤维增强复合材料(CFRP)加工时的面下损伤深度,创建了基于二维Hashin准则的宏观连续动态切削CFRP有限元模型,分析了切削力和面下损伤深度与纤维方向角之间的变化趋势,通过引入织构刀具来降低切削力及面下损伤深度,比较了沟槽形织构刀具、圆形织构刀具、三角形织构刀具切削CFRP的切削力和面下损伤。结果表明,不同织构刀具的切削力和面下损伤深度随纤维方向角变化趋势一致,均在0°时最小,90°达到最大值;织构刀具相对传统无织构刀具切削CFRP时均降低了切削力和面下损伤深度,其中圆形织构刀具降低程度最大;仿真模型经实验验证准确有效。 相似文献
75.
《中国航空学报》2016,(6):1788-1794
Dramatic tool temperature variation in end milling can cause excessive tool wear and shorten its life, especially in machining of difficult-to-machine materials. In this study, a new analyt-ical model-based method for the prediction of cutting tool temperature in end milling is presented. The cutting cycle is divided into temperature increase and decrease phases. For the temperature increase phase, a temperature prediction model considering real friction state between the chip and tool is proposed, and the heat flux and tool-chip contact length are then obtained through finite element simulation. In the temperature decrease phase, a temperature decrease model based on the one-dimension plate heat convection is proposed. A single wire thermocouple is employed to mea-sure the tool temperature in the conducted milling experiments. Both of the theoretical and experi-mental results are obtained with cutting conditions of the cutting speed ranging from 60 m/min to 100 m/min, feed per tooth from 0.12 mm/z to 0.20 mm/z, and the radial and axial depth of cut respec-tively being 4 mm and 0.5 mm. The comparison results show high agreement between the physical cutting experiments and the proposed cutting tool temperature prediction method. 相似文献
76.
77.
并联机床的模态分析有着重要的意义。本文针对3—HSS型并联机床,利用大型有限元软件ANSYS,对此并联机床进行了模态分析,分别获得了该机床的低阶固有频率及其对应的振型图,通过振动动画,分析了六阶模态的振动规律,找到了机床的薄弱环节,为机床的结构设计和动力学分析提供了依据。 相似文献
78.
针对复杂通道类零件的五轴数控加工,提出一种控制刀轴稳定变化的刀轴规划方法。首先,通过对刀轴可行空间的均匀离散,建立一种高效求解刀轴可行空间精细边界的方法;然后,依据刀轴矢量规划准则,求解满足机床角加速度约束的可行刀轴序列集合,并提出一种切削行内旋转坐标线性变化的刀轴矢量规划方法;最后,通过建立刀轴变化和残留高度综合评价指标,得到优化的刀轴矢量,并与典型的商用软件进行了实验对比验证。结果表明,使用本文提出的刀轴规划方法得到的切削行刀位轨迹旋转坐标变化均匀,旋转轴角加速度最大值降低到商用软件的10%以下,残留高度平均值降低了22%,改善了切削过程的稳定性,提高了加工表面质量。 相似文献
79.
朱春江 《航空精密制造技术》2016,(2)
在现代航空发动机的产品中,保护圈、密封件等零件广泛使用聚四氟乙烯材料制造.在加工中多采用车削加工,粗糙度一般为Ra1.6,本文通过选用不同车床、刀具、加工参数的方法,提高该类材料加工后的表面粗糙度,为后续加工提供经验和数据. 相似文献
80.
空心长轴深孔加工工艺研究 总被引:1,自引:0,他引:1
姜雪梅 《航空精密制造技术》2011,47(4):46-49
以某发动机空心长轴零件深孔加工为研究对象,设计了长径比为15,长度超过1米的整体硬质合金刀杆,在某加工项目试验中,应用这种超长整体硬质合金刀杆,在细长比大于10的空心长轴的深孔镗削加工中,改变了传统的深孔加工工艺,满足了空心长轴深孔加工中严格的壁厚差要求,取得了明显的效果. 相似文献