喷管扩张段烧蚀的“台阶效应”计算

当喉衬和扩张段内衬采用具有不同烧蚀率的材料时,常出现“台阶效应”.本文以气动热化学烧蚀机理为基楚,提出应用适当的对流换热和加剧的化学反应计算对台阶效应区进行修正的方法,使台阶效应区的烧蚀率预示更切合实际工况.     

Image restoration of the asymmetric point spread function of a high-resolution remote sensing satellite with time-delayed integration

The calibration and validation team of the Korea Aerospace Research Institute has calibrated and validated the image data of the KOMPSAT-2 since the launch of KOMPSAT-2 on July 28, 2006. The asymmetric phenomenon of the point spread function of the KOMPSAT-2 image data is evident in both the along and the across direction, most likely because KOMPSAT-2 has a 1 m ground sample distance high-resolution camera with time-delayed integration. Furthermore, because KOMPSAT-2 is in space, the KOMPSAT-2 image data has been corrected with good results by means of modulation transfer function compensation.     

Bursts in the HETE-2 catalogue

We have studied a set of GRBs detected by HETE-2 satellite with special focus on low-energy part of the spectrum. Results of data reduction procedures of different members of the HETE collaboration were combined with other publicly available information creating a concise catalogue. A more detailed analysis of lightcurves of the prompt emission was performed using data from FREGATE instrument.     

基于T-S模糊模型的模糊大系统的混合滤波

针对非线性大系统内部过程参数的检测估计,采用连续模糊大系统模型,利用lyapunov定理和分布式处理方法,给出了模糊大系统的H2/H∞混合滤波器设计方法。该方法在保证滤波误差系统全局稳定的同时,具备了H2/H∞性能。通过求解线性矩阵不等式,可以得到滤波器参数。最后,用一个数值例子验证了该方法的正确性和有效性。     

丁腈橡胶增韧环氧树脂基烧蚀防热材料性能

以丁腈橡胶(CTBN)为增韧剂对环氧树脂(F51)进行增韧改性,通过FTIR、TG以及力学性能测试研究了丁腈橡胶对环氧树脂固化反应、热稳定性能和力学性能的影响,并分析了其增韧机理;分别采用燃气流剪切烧蚀试验和电弧风动烧蚀实验考核了低密度烧蚀材料的烧蚀性能。结果表明:经CTBN改性后,两者的分子链产生了一定程度的交联;树脂基体的拉伸、弯曲性能有所下降,但韧性得到了增强;热稳定性大大提高,增韧后的F51树脂在800℃时的残重率由增韧前的23%提高到了54%;低密度烧蚀材料的抗剪切、抗剥蚀能力得到了增强,且碳层的尺寸稳定性也得到了改善,烧蚀性能提高。     

Ionospheric F2-Layer critical frequency retrieved from COSMIC radio occultation: A statistical comparison with measurements from a meridional ionosonde chain over Southeast Asia

In this paper, we compared the F2-Layer critical frequency (foF2) derived from FORMOSAT-3/COSMIC radio occultation (RO) and ionosondes at Chiang Mai, Chumphon and Kototabang during the years 2008–2015 to evaluate the performance of COSMIC RO over Southeast Asia region. The results show that the time development of foF2 values derived from COSMIC RO generally agrees well with those from ionosonde measurements. However, the differences between the foF2 derived from COSMIC RO and that derived from ionosonde observations display latitudinal dependence. COSMIC RO tends to underestimate foF2 at Chiang Mai and Kototabang, which is near to the north EIA crest and the south one, respectively, while a little overestimate foF2 at Chumphon, which is close to the geomagnetic equator. COSMIC RO agrees best with ionosonde at Chumphon and worst at Chiang Mai. At each ionosonde station, the quality of COSMIC RO data degrades with the increase of solar activity. In addition, at the station Chiang Mai and Kototabang, COSMIC RO performs better in summer than in equinox and winter. Furthermore, the differences in foF2 derived from COSMIC RO and that from ionosonde measurements vary with local time, i.e., the differences in foF2 are generally smaller at night and larger in noontime when equatorial ionization anomaly (EIA) is well developed.     

PBT弹性体力学性能及低温脆性研究

采用一步法制备了热固性3,3-双(叠氮甲基)环氧丁烷-四氢呋喃共聚醚(PBT)弹性体,并对其氢键结构、应力-应变关系和动态力学性能及低温脆性进行了研究。结果表明,合成的PBT弹性体拉伸强度和断裂伸长率在DEG羟基含量为35%、R=0.97时,可达2.51 MPa和1 274%,玻璃化温度为-34.5℃。高DEG含量的PBT弹性体脆化参数较低,与常温力学性能变化规律相反。因此,引入低温脆化参数,对PBT弹性体的性能优化具有积极意义。     

40CrNi2Si2MoVA钢喷丸强化层微观结构

喷丸强化在金属材料表面形成强化层,可以有效提高构件的疲劳寿命,是金属构件表面完整性制造的重要方法.喷丸强化已有效应用于40CrNi2Si2MoVA钢制构件,为了探明喷丸强化对该钢种的强化机理,本工作采用高分辨电子显微电镜(HREM)对40CrNi2Si2MoVA钢喷丸强化层微观组织结构进行了系统分析研究.结果表明:喷丸强化使40CrNi2Si2 MoVA钢组织细化,呈明显的马氏体“有效晶粒”现象,“有效晶粒”尺寸为几个纳米到几十个纳米;“有效晶粒”界面呈明显的倾转现象,相邻“有效晶粒”间转动角度为几度到几十度,最大达到30°.     

Al/Ni含能多层膜在Al2O3陶瓷/不锈钢焊接中的应用

采用磁控溅射设备,生长AuSn合金做焊料层、Al/Ni含能多层膜做热量提供层,实现了不锈钢和Al_2O_3间的异质材料自蔓延高温扩散焊。利用SEM、XRD和DSC等测试手段表征AuSn合金和Al/Ni含能多层膜的微观形貌、相成分和放热量;用万能试验机测试焊接接头的力学性能。结果表明,AuSn合金的质量比基本达到80∶20,而多层膜的层状结构清晰,反应热达到1 239 J/g。焊接实验结果表明,仅使用AuSn焊料时,剪切强度仅为46 MPa,在增加Al/Ni含能多层膜后,其剪切强度可达90 MPa,强度提高了约一倍。焊接接头的界面显微形貌和相结构研究表明,剪切强度的增强主要是Al/Ni多层膜提供了额外能量使得界面处的反应剧烈,陶瓷金属化层与中间层的反应加剧,形成了新的反应生成物。     

改性双马来酰亚胺树脂预浸料性能研究

采用二烯丙基双酚A(Ortho-dially Bisphenol A,以下简称O-DABPA)对T型双马来酰亚胺(Bismaleimide,以下简称BMI)树脂进行改性,并用红外光谱(Fourier TransformInfrared,以下简称FT-IR)、差式扫描量热仪(Differential ScanningCalorimetry,以下简称DSC)对改性前后的树脂结构及固化反应进行测定,利用热熔预浸法对改性BMI树脂制备预浸料,考查了预浸料的力学性能及高温下的弯曲性能。结果表明,在175℃下二烯丙基双酚A和T型双马来酰亚胺树脂质量比为1∶1,反应时间为1 h时,改性BMI树脂制备的预浸料工艺性良好,单向板层间剪切强度为84.86 Mpa,在240℃时,弯曲强度及模量分别为1 326.41 MPa和120.31 GPa,强度保留率为76.73%。