温度对飞机燃油射流泵工作特性影响

建立了射流泵数学模型,采用数值计算方法对其工作特性进行了模拟,搭建了实验台,采用RP-3燃油,通过实验数据验证了模型的正确性.在此基础上,分别选择了RP-3和JET-A两种燃油,计算了从-40℃~40℃温度下,不同操作压力对射流泵流量比的影响.结果表明:燃油温度高于0℃时,温度对射流泵工作特性影响并不明显,随着温度的降低,射流泵性能与标准温度下（20℃）偏差越来越大,且压比越高此偏差越明显.当温度高于0℃时,采用RP-3和JET-A燃油性能相差不大,RP-3燃油性能略优于JET-A燃油,但是在低温下,RP-3燃油性能远高于JET-A燃油.因此当燃油温度较低且压比较高时,必须充分考虑温度对射流泵特性的影响.      

Effects of synthetic jet frequency on the separated flow in a diffusing S-duct

Numerical simulations were carried out to investigate the effects of synthetic jet actuation frequency on the separated flow in a diffusing S-duct. The Reynolds number based on the entrance height was 9.78×105. At first, the numerical model was validated with experimental data, and then, the interaction between the separated flow and the synthetic jets at different frequencies was discussed. The results demonstrate that the control effect is significantly dependent on the momentum mixing enhancement between inside of the separated boundary layer and the outer flow. There exists a narrow range of actuation frequency, in which effective separation control can be achieved using synthetic jets. A dimensionless frequency F+=1.0 is identified as the optimal frequency, with a momentum coefficient of 1.62×10-3, the separation area is reduced about 46%, and the aerodynamic performance of the S-duct is also greatly improved compared to uncontrolled case. Further analysis reveals that the choice of actuation frequency is mainly determined by the momentum flux produced by a single ejection and the spacing between adjacent ejections, the optimal frequency case can be understood as a balance between the two factors. In addition, it is found that the synthetic jets can also suppress the secondary flows while decreasing the separation.      

微流量测量方法及其技术的发展

归纳了近五年来基于MEMS技术的微流量传感器结构及性能参数。根据国际上热门的研究方法推断微流量测量技术可能的发展方向与研究趋势,即集成两种或两种以上的测量方法,实现优势互补,提高测量精度或扩大量程比。最后基于现有的技术基础,提出了融合科氏效应与差压效应的微流量测量方法,阐述了传感器的工作原理与理论基础,并对其可行性进行了分析与论证。     

Development process of muzzle flows including a gun-launched missile

Numerical investigations on the launch process of a gun-launched missile from the muzzle of a cannon to the free-flight stage have been performed in this paper. The dynamic overlapped grids approach are applied to dealing with the problems of a moving gun-launched missile. The high-resolution upwind scheme(AUSMPW+) and the detailed reaction kinetics model are adopted to solve the chemical non-equilibrium Euler equations for dynamic grids. The development process and flow field structure of muzzle flows including a gun-launched missile are discussed in detail.This present numerical study confirms that complicated transient phenomena exist in the shortly launching stages when the gun-launched missile moves from the muzzle of a cannon to the freeflight stage. The propellant gas flows, the initial environmental ambient air flows and the moving missile mutually couple and interact. A complete structure of flow field is formed at the launching stages, including the blast wave, base shock, reflected shock, incident shock, shear layer, primary vortex ring and triple point.     

高性能G-M型单级脉管制冷机研究

从直流抑制角度出发，开展了高性能G—M型单级脉管制冷机的研究。在对各种直流抑制方式进行比较的基础上，利用双向进气阀流量系数的方向性，采用两个并联排列、指示箭头方向相反的阀门，称之为并联逆向双阀双向进气结构对直流进行抑制，成功地解决了传统单阀双向进气结构脉管制冷机的直流问题。在2kW(RW2)和4kW(CP4000)压缩机驱动时分别获得了18．4K和14．7K的最低制冷温度，对应在30K的制冷量为11．5W和29．5W，这些都是目前单级脉管制冷机公开报道的最好结果。     

谈飞机结构装配工艺中几个细节问题的完善

基于飞机生产过程中长期固存的问题进行要点采摘,对于操作者在生产过程中的认识误区、原因分析做出比较详尽的叙述,对于完善设计和改良产品质量能够提供一定的帮助.     

CONTROL OF TWO DIMENSIONAL JETS USING MINIATURE ZERO MASS FLUX JETS

Zero mass flux jets, synthesized by acoustic actuators, have been used for the purpose of jet mixing enhancement and jet vectoring. Zero mass flux jets composed of entirely entrained fluid allow momentum transfer into the embedding flow. In the present experiments, miniature-scale high aspect ratio actuator jets are placed along the long sides and near the exit plane of a primary two-dimensional jet. In different modes, the primary jet can be vectored either towards or away from the actuator jets and the jet mixing is enhanced. The disturbance of the excitation frequency is developed while the unstable frequency of the primary jet is completely suppressed.     

可调静子旋转凸台位置对端区流动的影响

对包含凸台的可调静子模型进行简化,研究了不同凸台位置对端区流动的影响.通过实验测量与数值模拟对比可以发现:可调静子端区流动损失主要是由叶片气动负荷引起的泄漏及气流绕过凸台造成的掺混2个部分组成;通过合理优化设计,将凸台置于气动负荷高的叶片前缘并覆盖尽可能多的前缘间隙,能够有效降低损失,改善气动性能.      

一种用于分离流动的网格自适应算法

对于可压缩粘性流动,提出利用流场速度的紊乱度作为指示变量进行网格自适应.Jameson中心格式有限体积法、五步Runge-Kutta时间推进法/双时间推进法求解定常/非定常N-S方程.基于雷诺平均N-S方程模拟紊流,选用SA一方程模型.在数值求解二维静态失速和动态失速问题过程中,加入网格自适应算法,提高数值模拟对流动分离特性的捕捉和分辨能力.算例结果表明在流场发生失速后,运用本文的自适应算法能够在增加少量网格单元的情况下明显提高计算精度.     

直径比对冲击气膜组合冷却流动与换热的影响

 通过数值模拟,研究了涡轮叶片弦中区所采用的新型双层腔冷却结构的冷却特性,系统分析了冲击气膜组合冷却的流动与换热特性,讨论了冷气进口雷诺数Re、吹风比M以及气膜孔与冲击孔的直径比D/d对组合冷却效果的影响。计算参数范围是：冷气进口雷诺数Re＝2 000～5 000,吹风比M＝0.6～2.0。计算结果表明, 冷气进口Re,M以及D/d对双层腔结构冷却效果的影响非常明显,在计算范围内:（1）Re和M越高,冷却效果越好;（2）当冲击孔直径一定时,增加气膜孔的直径,冷却效果会随之增加;（3）当冲击孔直径一定时,增加气膜孔的直径,流阻系数会随之减小。