Precise orbit determination for TH02-02 satellites based on BDS3 and GPS observations

The Tianhui-2 02 (TH02-02) satellite formation, as a supplement to the microwave mapping satellite system Tianhui-2 01 (TH02-01), is the first Interferometric Synthetic Aperture Radar (InSAR) satellite formation-flying system that supports the tracking of BeiDou global navigation Satellite system (BDS3) new B1C and B2a signals. Meanwhile, the twin TH02-02 satellites also support the tracking of Global Positioning System (GPS) L1&L2 and BDS B1I&B3I signals. As the spaceborne receiver employs two independent boards to track the Global Navigation Satellite System (GNSS) satellites, we design an orbit determination strategy by estimating independent receiver clock offsets epoch by epoch for each GNSS to realize the multi-GNSS data fusion from different boards. The performance of the spaceborne receiver is evaluated and the contribution of BDS3 to the kinematic and reduced-dynamic Precise Orbit Determination (POD) of TH02-02 satellites is investigated. The tracking data onboard shows that the average number of available BDS3 and GPS satellites are 8.7 and 9.1, respectively. The carrier-to-noise ratio and carrier phase noise of BDS3 B1C and B2a signals are comparable to those of GPS. However, strong azimuth-related systematic biases are recognized in the pseudorange multipath errors of B1C and B3I. The pseudorange noise of BDS3 signals is better than that of GPS after eliminating the multipath errors from specific signals. Taking the GPS-based reduced-dynamic orbit with single-receiver ambiguity fixing technique as a reference, the results of BDS3-only and BDS3 + GPS combined POD are assessed. The Root Mean Square (RMS) of orbit comparison of BDS3-based kinematic and reduced-dynamic POD with reference orbit are better than 7 cm and 3 cm in three-Dimensional direction (3D). The POD performance based on B1C&B2a data is comparable to that based on B1I&B3I. The precision of BDS3 + GPS combined kinematic orbit can reach up to 3 cm (3D RMS), which has a more than 25% improvement relative to the GPS-only solution. In addition, the consistency between the BDS3 + GPS combined reduced-dynamic orbit and the GPS-based ambiguity-fixed orbit is better than 1.5 cm (3D RMS).     

耐高温复合材料在火星探测器着陆器减速伞筒盖结构上的应用

针对火星探测器着陆巡视器减速伞筒盖结构在轨运行耐温度交变、辐照等空间环境和再入过程耐温度冲击性能需求,重点开展了筒盖复合材料耐温匹配性、力学性能、耐空间环境性能以及制件成型工艺研究。结果表明,选用J-168-1胶黏剂、J-245胶黏剂及T300/QY8911复合材料制备的试件通过各项性能试验考核,均能满足筒盖结构的设计指标要求。筒盖产品力学性能稳定,成型工艺可行性良好,最高瞬时使用温度可达200℃,经历空间环境模拟后力学性能保持率均在80%以上,耐高温、耐空间环境性良好。产品已成功装星发射,并在着陆巡视器落火阶段成功弹出分离,圆满完成使命。     

激光熔化沉积15-5PH沉淀硬化不锈钢组织及拉伸性能

利用激光熔化沉积技术制备15-5PH沉淀硬化不锈钢板,利用金相显微镜(OM)、扫描电镜(SEM)、透射电镜(TEM)、电子探针(EPMA)技术,对沉积态组织进行分析,测试沉积态组织的室温拉伸性能。结果表明:激光熔化沉积15-5PH不锈钢沉积态组织由沿沉积增高方向贯穿多层外延生长的柱状晶组成,柱状晶内包含多个细长整齐排列的胞状树枝晶,枝晶内为马氏体组织,枝晶间为铁素体;沉积态组织中弥散分布大量细小的NbC析出相,尺寸12～20 nm;15-5PH不锈钢沉积态组织具有良好的力学性能,纵向抗拉强度和延伸率分别为1 128.5 MPa和14.0%,横向抗拉强度和延伸率分别为1 101 MPa和12.25%。     

Through-thickness heterogeneity in creep properties of friction stir welding 7B50-T7451 aluminum alloy thick plate joint: Experiments and modeling

Through-thickness heterogeneity in creep properties of 7B50-T7451 aluminum alloy Friction Stir Welding(FSW) joints was investigated. Creep tests for three slices of the FSW joint were conducted at the temperature of 150–200 °C and applied stress of 60–225 MPa. The theta projection method was used to predict creep curves and minimum creep rate. The results show that the minimum creep rate increases and creep rupture life decreases with the increase of creep temperature and applied stress. Creep p...     

基于1553B总线的星载嵌入式软件在轨升级方法

针对星载嵌入式软件在轨升级难的问题,提出了基于1553B总线的星载嵌入式软件在轨(线)升级方法。通过1553B总线接收升级程序、固化程序和升级程序分区独立存储、启动程序和应用程序互相配合的方式,实现软件升级、部分传输异常时补丁升级及升级异常情况下的版本回退。在某星载固态存储设备上对方法进行了试验验证,结果表明,方法可对星载固态存储设备的软件进行在轨(线)升级,升级程序异常情况下可通过设备开关电自动回退版本,部分出错时上注补丁量少,提高了星载嵌入式软件测试维护和在轨维护的效率和可靠性。