多斜孔冷却方式气动参数对壁温梯度和冷却效率的影响

针对高温升燃烧室以延长其火焰筒使用寿命为目的,实验研究了多斜孔冷却方式气动参数,如加温比、速度比和主流速度变化对主燃烧室火焰筒壁温梯度和冷却效率的影响.实验结果表明:减小加温比或增大速度比都可以减小壁温梯度的绝对值,同时冷却效率也会增加;当主流进入了自模区后,随着主流速度的增加,壁温梯度的绝对值会减小,冷却效率会增大.      

基于遗传算法的液体火箭发动机参数优化

建立了液体火箭发动机系统设计的仿真模型和多目标优化模型,采用组合优化策略和遗传算法,针对全流量补燃循环发动机,进行了不同设计变量和目标函数下发动机性能参数的优化,求得全局最优解.计算结果表明,遗传算法是解决该类问题的有效方法,可为其它类似发动机的优化提供一定的指导作用.      

民用发动机污染排放及低污染燃烧技术发展趋势

针对民用发动机污染排放的现状,介绍了低污染燃烧技术发展概况及趋势,国际民航组织(ICAO)颁布的《航空发动机的排放》标准,以及中国民用航空局(CAAC)对排气污染物的规定,分析了排气污染物的生成机理和主要影响因素以及改善措施.对6种先进低污染燃烧室(分级、变几何、催化、贫油预混预蒸发燃烧室(LPP)、富油燃烧/淬熄/贫油燃烧技术(RQL)以及双环预混旋流(TAPS)等燃烧室)的工作原理与特点、以及应用状况作了简要分析.其中分级燃烧技术构成了先进低污染燃烧室设计的技术基础,而LPP,RQL与TAPS燃烧室为三种很有发展前途的低污染燃烧室.此外,还介绍了贫油直接喷射、燃料电池以及主动燃烧控制等三种新型的低污染燃烧技术,虽然实现这些技术难度较大,但有广阔的应用前景.      

基于卡尔曼滤波器及神经网络的发动机故障诊断

提出了一种基于卡尔曼滤波器及神经网络的航空燃气涡轮发动机气路故障诊断的方法.该方法用卡尔曼滤波器来估计发动机可测参数的变化量,再由神经网络来映射发动机性能参数的变化量,并据此进行发动机气路故障诊断.数字仿真表明,该方法是可行的,有效的.      

应用非均匀B样条拟合涡轮发动机部件特性

为了使气动热力模型更好的逼近涡轮发动机,应用成熟的非均匀B样条来拟合部件特性.这种方法既可以保证发动机计算的整体性能也大大提高了其局部特性的准确性.单轴涡喷发动机的算例证明了方法的有效性.      

一种涡轮发动机加速控制规律设计的新方法

 提出了一种涡喷、涡扇发动机加速控制规律快速设计的新方法：在发动机稳态特性计算模型的基础上,通过额外增加转子提取功率,使得发动机稳态工作点（线）靠近喘振边界,在同时考虑燃烧室富油熄火边界、涡轮进口总温限制以及压气机喘振裕度限制的条件下,利用适当的控制规律描述形式并结合发动机工程研制中的经验,能够快速而准确地获得涡喷、涡扇发动机加速控制规律。对某型涡喷发动机加速控制规律的改进的计算结果表明,提出的加速控制规律的设计方法准确而有效。     

金属橡胶减振器用于发动机安装减振的研究

 为减小发动机传递至飞机机身结构的振动,设计了金属橡胶减振器用于航空发动机安装。对该金属橡胶减振器进行了动力学建模研究,采用有限元技术对安装减振器前后的飞机全机结构进行了仿真分析,初步表明了该设计对结构频率影响较小,但能引入较大阻尼,降低响应水平。在理论分析基础上,进一步将设计制造的金属橡胶减振器安装于某型飞机,进行地面开车,实测了应用减振安装前后飞机的动力学响应。结果证明了发动机减振安装的可行性与有效性。     

多机并联火箭羽流流场及其底部热环境分析

针对某多机并联火箭羽流流场结构复杂、底部热环境极为恶劣,有可能导致发动机结构部件失效的问题,通过数值仿真对其飞行过程不同高度下的羽流流场及热环境进行研究,并与热环境实测结果进行了对比分析。计算结果表明:火箭低空飞行时,各发动机羽流互不干扰,随着飞行高度不断增加,羽流逐渐扩张并开始相互干扰,最后在箭体底部出现明显回流,最大热流在起飞时刻,与飞行实测值基本一致。出现回流之前,箭体底部主要受辐射热影响,随着回流出现,对流热流随之增大,但也远小于起飞时刻的热流峰值。计算得到的多机并联火箭羽流流场及其热环境分布对发动机舱外结构热防护优化设计具有一定的指导意义。     

Designing method of acceleration and deceleration control schedule for variable cycle engine

Studies show that different geometries of a Variable Cycle Engine (VCE) can be adjusted during the transient stage of the engine operation to improve the engine performance. However, this improvement increases the complexity of the acceleration and deceleration control schedule. In order to resolve this problem, the Transient-state Reverse Method (TRM) is established in the present study based on the Steady-state Reverse Method (SRM) and the Virtual Power Extraction Method (VPEM). The state factors in the component-based engine performance models are replaced by variable geometry parameters to establish the TRM for a double bypass VCE. Obtained results are compared with the conventional component-based model from different aspects, including the accuracy and the convergence rate. The TRM is then employed to optimize the control schedule of a VCE. Obtained results show that the accuracy and the convergence rate of the proposed method are consistent with that of the conventional model. On the other hand, it is found that the new-model-optimized control schedules reduce the acceleration and deceleration time by 45% and 54%, respectively. Meanwhile, the surge margin of compressors, fuel–air ratio and the turbine inlet temperature maintained are within the acceptable criteria. It is concluded that the proposed TRM is a powerful method to design the acceleration and deceleration control schedule of the VCE.     

Exploring mission planning method for a team of carrier aircraft launching

High-level efficiency and safety are of great significance for improving the fighting capability of an aircraft carrier. One way to enhance efficiency and safety level is to organize the carrier aircraft into combat effectively. This paper studies the mission planning problem for a team of carrier aircraft launching, and a novel distributed mission planning architecture is proposed. The architecture is hierarchical and is comprised of four levels, namely, the input level, the coordination level,the path planning level and the execution level. Realistic constraints in each level of the distributed architecture, such as the vortex flow effect, the crowd effect and the motion of aircraft, are considered in the model. To solve this problem, a distributed path planning algorithm based on the asynchronous planning strategy is developed. The proposed Mission Planning Approach for Carrier Aircraft Launching(MPACAL) is validated using the setups of the Nimitz-class aircraft carrier.Compared to the isolated planning architecture and the centralized planning architecture, the proposed distributed planning architecture has advantages in coordinating the launch tasks not only belonging to the same catapult but also when all different catapults are considered. The proposed MPACAL provides a modeling method for the flight deck operation on aircraft carrier.