排序方式: 共有106条查询结果,搜索用时 312 毫秒
31.
针对航空发动机PID控制器的参数寻优问题,提出基于人工蜂群算法(ABC)的航空发动机PID控制器参数自整定的方法。利用人工蜂群算法实现容易、计算简洁、寻优性能好、鲁棒性强的优点,优化PID控制器参数,以改善控制系统性能。考虑到可能存在的执行机构输出量的极大超调,融入执行机构输出的超调量惩罚机制,改进目标性能函数,有效避免了可能存在的发动机供油量极大超调现象。对涡扇发动机在地面和高空稳态工作点的增量形式的线性化数学模型进行了仿真验证,结果表明优化效果良好,转速阶跃响应反应迅速且超调量小,同时供油量也没有出现大的超调,验证了所提方法的有效性和实用性。 相似文献
32.
33.
34.
为了解某型发动机整机运行状态下低压涡轮工作叶片的温度分布情况,使用红外测试系统测量了该发动机整机状态低压涡轮工作叶片前缘及盆侧的温度场。试验前对该发动机进行了测试改装,设计了用于实现叶片定位的转速信号分析仪,以及用于提供高压气源的气体增压系统。试验共测得多个状态下发动机涡轮叶片的表面温度分布数据。结果表明:涡轮叶片前缘和叶盆中间位置的温度较高;相同位置下每片叶片的温度有轻微差异;叶片的最高温度位置位于测试区域的下方,与仿真计算结果相吻合。采用红外测温技术可以得到清晰的涡轮叶片表面温度分布云图,结合示温漆标记技术,可用于定位温度最高的叶片和叶片温度最高的位置。 相似文献
35.
36.
通过试验、分析、比较,提出了高温、高稳定性压电元件的研制要求,并确认了铋钛系列晶体是制作压电加速度传感器较理想的材料. 相似文献
37.
38.
《中国航空学报》2021,34(4):526-539
This paper proposes a Linkage Learning Genetic Algorithm (LLGA) based on the messy Genetic Algorithm (mGA) to optimize the Min-Max fuel controller performance in Gas Turbine Engine (GTE). For this purpose, a GTE fuel controller Simulink model based on the Min-Max selection strategy is firstly built. Then, the objective function that considers both performance indices (response time and fuel consumption) and penalty items (fluctuation, tracking error, overspeed and acceleration/deceleration) is established to quantify the controller performance. Next, the task to optimize the fuel controller is converted to find the optimization gains combination that could minimize the objective function while satisfying constraints and limitations. In order to reduce the optimization time and to avoid trapping in the local optimums, two kinds of building block detection methods including lower fitness value method and bigger fitness value change method are proposed to determine the most important bits which have more contribution on fitness value of the chromosomes. Then the procedures to apply LLGA in controller gains tuning are specified stepwise and the optimization results in runway condition are depicted subsequently. Finally, the comparison is made between the LLGA and the simple GA in GTE controller optimization to confirm the effectiveness of the proposed approach. The results show that the LLGA method can get better solution than simple GA within the same iterations or optimization time. The extension applications of the LLGA method in other flight conditions and the complete flight mission simulation will be carried out in part II. 相似文献
39.
为了研究后挡板结构对刷式密封泄漏特性的影响,模拟航空发动机静态和动态工况,对三种不同后挡板结构的刷式密封泄漏特性进行实验研究。实验结果表明:相比于标准型刷式密封,后挡板结构中设计环形平衡腔能有效缓解刷式密封刷丝滞后效应,但间隙值过大将导致刷式密封性能下降;刷式密封实验件b(有环形平衡腔,与刷丝束之间的间隙为0.2mm)的泄漏参数Φ2保持在7 g﹒K1/2﹒mm/(N﹒s)以内,表现出优异的密封性能,这说明合适的环形平衡腔间隙值设计,能有效缓解刷式密封刷丝滞后现象。根据实验结果,环形平衡腔的间隙设计值应不大于0.4mm。 相似文献
40.
为了验证多级轴流压气机出口级性能,开展四级重复级低速模拟气动设计,并坚持以二维设计为主,三维数值验证为辅。利用相同的设计系统,建立了高低速压气机之间相似的二维流场和叶表无量速度分布。随后,低速与高速压气机三维数值计算结果对比表明,压升系数特性吻合,流场相似,且叶表无量纲速度由设计点到失速点保持一致的变化趋势,进一步验证了二维设计的可行性;利用相同的系统设计高、低速压气机,有利于形成高速-低速-高速的良性循环,有利于完善基于通流程序的设计体系,积累设计经验。 相似文献