高超音速飞行的总温总压计算

本文用化学平衡定熵变成份变比热热力计算法(以下称热力计算法〕计算了Ma=0～7.00、高度H=0～40km的总温、总压随Ma数及高度H的变化规律.计算结果与定成份定比热的气动函数法(下称气动函数法)和修正系数法的计算结果及R-R公司的引用数据进行了比较.给出了总温、总压的相对误差δ_T、δ_P随Ma数及H的变化规律.计算表明,热力计算法与气动函数法相比较,在Ma>3.0之后有显著的差别.     

TC21钛合金的微观组织对力学性能的影响

研究了两相钛合金TC21关于两种不同微观组织(片状组织和网篮组织)的拉伸性能、断裂韧性和疲劳裂纹扩展性能.结果显示:片状组织相比网篮组织有相近的拉伸强度,但塑性较差;两者的韧性相差不大,但增韧机理不同;网篮组织在中低速扩展区的扩展速率和片状组织几乎相同,但在较高速扩展区显示略低的扩展速率;加载方向对两种组织的疲劳裂纹扩展速率基本无影响;和其他钛合金类似,TC21在Paris区存在转折.     

一种分析稳态压力畸变对多级轴流压缩系统稳定性影响的新方法

发展了一种分析进口稳态压力畸变对多级轴流压缩系统稳定性影响的逐级平行压缩系统模型；建立了一种稳态压力畸变进气条件下，多级轴流压缩系统对燃烧室燃油瞬时脉冲的气动响应及气动稳定性分析的新方法；导出了基于ＭａｃＣｏｒｍａｃｋ隐式格式的新的数值计算方法。应用新的模型方法对一个三级实验压气机进行了数值分析，给出了稳态压力畸变与压缩系统稳定裕度损失及不稳定发生时间之间的定量关系，定量给出了压气机失稳首发级的识别方法。     

叶轮机非定常气动设计的缘线匹配(II)数值研究

缘线匹配通过考虑多叶排叶轮机相邻叶排间前排叶片尾缘线与后排叶片前缘线空间相对位置匹配关系来进一步提升叶轮机性能,有潜力使叶轮机非定常设计走向工程实际。以一单级跨声轴流压气机和一单级轴流透平为例,尝试用基元流动展向积分方法和全优化方法改善其性能,从而示例应用缘线匹配的具体方法及前景。结果表明,缘线匹配为叶轮机非定常设计提供了可操作的自由度。     

推力向量控制方案及计算

本文归纳推力向量控制的主要方案,着重介绍摆动喷管、流体二次喷射方案的计算思路和结果.摆动喷管中的流场计算要考虑导弹偏摆对所产生的惯性力的影响;所得壁面压力畸变图说明,它是一个三维流场.在摆动喷管设计中要将铰链力减至最小,流体二次喷射的侧向力通过“等效实体模型”,用爆炸波的解来计算.     

腰形柱壳的有限条元解

本文用考虑了曲率影响的两结线低阶有限板条元分析了腰形柱壳的力学性能这种条元位移参数少,能较好地体现壳体的几何特性。     

A novel surrogate modeling strategy of the mechanical properties of 3D braided composites

In this paper, a surrogate-based modeling methodology is developed and presented to predict the elastic properties of three dimensional (3D) four-directional braided composites. Using this approach, the prediction process becomes feasible with only a limited number of training points. The surrogate models constructed using Finite Element (FE) method and Diffuse Approximation, reduce the computational time and cost for preparing experimental samples. In the FE model, multiscale method is applied to couple the computations of elastic properties at microscale and mesoscale. Subsequently, a parametric study is performed to analyze the effects of the three design parameters on the elastic properties. Satisfactory results are obtained via the surrogate-based modeling predictions, which are compared with the experimental measurements. Moreover, the predictions obtained from surrogate models concur well with the FE predictions. This study orients a new direction for predicting the mechanical properties based on surrogate models which can effectively reduce the sample preparation cost and computational efforts.     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

Effects of process parameters on mechanical properties of abrasive-assisted electroformed nickel

A cathode mandrel with translational and rotational motion, which was supposed to obtain uniform friction effect on surface, was employed in abrasive-assisted electroforming for revolving parts with complex profile. The effects of current density, translational speed and rotational speed on the deposit properties were studied by orthogonal test. The tensile strength, elongation and micro hardness value were measured to find out how the factors affected the properties. The optimized results show that changes of current density affect the tensile strength of nickel layer most, while translational speed has the most remarkable influences on both elonga-tion and micro hardness. The low rotational speed affects the properties least. In this experiment, a smooth nickel layer with tensile strength 581 MPa, elongation 17%and micro hardness 248HV is obtained by the orthogonal test.     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.