一类有理递归序列的全局稳定性

研究了下列差分方程平衡点的全局渐近稳定性、全局吸引性以及周期性xn＋1=α-xn-k/xn,n=0,1,…,式中;x-k,x-k＋1,…,x0为任意实数,α为一实数,k为一整数.     

叶片前缘改型对涡轮叶栅二次流的影响

以某典型高压涡轮叶栅为研究对象,采用数值模拟的方法对比分析了两种端壁前缘改型结构对涡轮叶栅二次流产生的影响。结果表明,带状结构(Fillet)以及适当尺寸的球形结构(Bulb)可以改善涡轮叶栅内部二次流,并且降低涡轮出口气动损失。其中尺寸的选择对于球形结构(Bulb)影响很大。两种不同的改型结构相比较,带状结构(Fillet)改型方案对二次流的改善效果较为明显,结果更为理想。     

有翼再入飞行器的超/高超声速气动力工程方法

有翼再入飞行器气动力的工程计算方法尚有待进一步完善,计算精度有待进一步提高。文章根据有翼再入飞行器的气动布局特点,改进和发展了一套适于其气动布局的部件划分策略和压强计算选取准则。以此对航天飞机轨道器和类X-34飞行器的纵向气动力特性进行工程计算,并与其风洞试验和数值模拟结果进行对比分析。结果表明,文中的工程计算方法在马赫数3以上的超/高超声速范围内可准确预测有翼再入飞行器的升阻特性,其中升力系数和阻力系数误差小于10%;并可准确预测俯仰力矩特性随迎角改变的变化规律。与现有方法相比,文中的部件划分策略和压强计算选取准则在升阻特性精度相当情况下,可明显提高俯仰力矩的预测精度,并反映飞行器表面的压强分布特征。     

开槽尾流板对跨声速涡轮平面叶栅流场影响的实验

采用数值计算和实验相结合的方式研究了开槽尾流板对跨声速涡轮平面叶栅流场周期性的影响。通过数值计算研究了不同开孔率（10%、15%、30%、50%）和偏转角度（70°、71°、72°）下尾流板对叶片表面及叶栅流道出口压力分布的影响,并通过实验验证了尾流板对流道出口流场周期性的改善作用。结果表明:无尾流板时叶片表面压力分布明显偏离周期性计算结果,且流道出口压力分布的周期性误差较大;尾流板偏转角度和开孔率会影响叶片表面及叶栅流道出口的压力分布,适当调节尾流板参数能改善流场周期性;安装开孔率为50%,偏转角度为70°的尾流板时各流道出口的压力分布一致性最好且最接近周期性计算结果,计算和实验结果的周期性误差较无尾流板时分别降低47.6%和28.1%。      

无人机制造外形气动偏差评估方法

气动外形对无人机起着至关重要的作用,有必要对其制造外形的气动偏差进行评估。利用数字摄影测量系统获得无人机制造外形的点云数据;以机头为参考点,将测量点云数据模型与理论模型的坐标系重合,对比重合度并统计无人机制造外形与理论外形的几何偏差分布;根据点云数据进行逆向建模,获得无人机制造外形的三维模型;对无人机理论外形进行CFD计算,与其风洞试验数据进行对比,通过调整网格及计算方法,得到与试验数据相吻合的CFD计算方法;以此方法计算得到无人机制造外形的气动数据,并与无人机的理论气动力进行对比。结果表明:此评估方法能够定量地评估外形制造偏差对无人机气动特性的影响。     

Effects of pressure oscillation on aerodynamic characteristics in an aero-engine combustor

The effects of pressure oscillation on aerodynamic characteristics in an aero-engine combustor are investigated. A combustor test rig is designed to simulate the pressure drop characteristics of a practical annular combustor. The pressure drop characteristics are firstly measured under atmosphere condition with non-reacting flow (or cold flow), and the air mass flow proportion of each component (dome/liner) are obtained; these properties are base lines for comparison with combustion state. The combustion tests are then carried out under conditions of inlet temperature 340–450 K, fuel air ratio 0.010–0.028. The stability map and the oscillation frequencies are obtained in the tests, the results show that pressure oscillation amplitude increases with the increase of fuel air ratio. Phase trajectory reconstruction is applied to classify the pressure oscillation motion; there are three motions captured in the tests including: “disk”, “ring” and “cluster”. The pressure drops across the dome under strong pressure oscillation are distinctly divergent from the cold flow, and the changes of pressure drops are mainly affected by pressure oscillation amplitude, but is less influenced by pressure oscillation motion nor oscillation frequencies. Based on the mass flow conservation, the reduction of effective flow area of combustor under strong pressure oscillation is demonstrated. Liner wall temperatures are analyzed through Multiple Linear Regression (MLR) method to estimate the reduction of the air mass flow proportion of the liner cooling under strong pressure oscillation. Finally, the air mass flow proportions of each component under strong pressure oscillation are estimated, the results show that the pressure oscillation motion also has influence on air mass flow proportion.     

Aerodynamic performance of owl-like airfoil undergoing bio-inspired flapping kinematics

Natural flyers have extraordinary flight skills and their prominent aerodynamic performance has attracted a lot of attention. However, the aerodynamic mechanism of birds' flapping wing kinematics still lacks in-depth understanding. In this paper, the aerodynamic performance of owl-like airfoil undergoing bio-inspired flapping kinematics extracted from a free-flying owl wing has been numerically investigated. The overset mesh technique is used to deal with the large range movements of flapping airfoils. The bio-inspired kinematics consist of plunging and pitching movement. A pure sinusoidal motion and a defined motion composed of plunging of sinusoidal motion and pitching of the bio-inspired kinematics are selected for comparison. The other two NACA airfoils are also selected to figure out the advantages of the owl-like airfoil. It is found that the cambered owl-like airfoil can enhance lift during the downstroke. The bio-inspired kinematics have an obvious advantage in lift generation with a presence of higher peak lift and positive lift over a wider proportion of the flapping cycle. Meanwhile, the bio-inspired motion is more economical for a lower power consumption compared with the sinusoidal motion. The sinusoidal flapping motion is better for thrust generation for a higher peak thrust value in both upstroke and downstroke, while the bio-inspired kinematics mainly generate thrust during the downstroke but produce more drag during the upstroke. The defined motion has similar lift performance with the bio-inspired kinematics, while it consumes more energy and generates less thrust. The unsteady flow field around airfoils is also analyzed to explain the corresponding phenomenon. The research in this paper is helpful to understand the flight mechanism of birds and to design a micro air vehicle with higher performance.     

基于Gauss伪谱法的临近空间飞行器上升段轨迹优化

综合考虑密度变化、声速变化、发动机推力变化及地球引力等因素对飞行轨迹的影响,研究了与实际飞行环境更加相符的临近空间飞行器燃料最优爬升轨迹。针对该问题在气动数据处理和优化求解上存在的困难,提出一种基于Gauss伪谱法(Gauss Pseudospectral Method,GPM)的求解策略。首先,依据气动数据特点,设计拟合模型对气动参数进行高精度拟合;其次,为避免间接法和传统直接法的缺点,将Gauss伪谱法和序贯二次规划(Sequential Quadratic Programming,SQP)相结合,对存在边值及加速度约束的轨迹优化问题进行求解,获得最优飞行轨迹。仿真结果表明,在更为真实的飞行环境下,利用GPM和SQP相结合的方法可在5.83s获得一条精度为10-4～10-6左右的飞行轨迹。     

高超声速再入钝头体表面热流计算

采用边界层外缘无黏流场数值求解三维可压缩定常Euler方程,将所得物面压力分布作为边界层外缘条件,用于边界层内跟踪流线的轴对称比拟工程算法,计算高超声速有攻角再入钝头体的表面热流。某钝双锥算例结果表明:算得的表面热流与实验数据吻合很好。该方法较纯工程算法提高了精度,较数值求解整个流场Navi-er-Stokes方程节省计算时间,对准确计算全轨道飞行复杂形状高超声速飞行器表面的热流分布有一定价值,适宜高超声速飞行器方案设计阶段气动热环境预测的需要。     

基于参数化外形的通用大气飞行器建模与分析

提出了一类翼身组合升力体外形通用大气飞行器(Common Aero Vehicle, CAV)的参数化外形建模方法,采用气动工程预估方法计算CAV的气动系数,拟合得到能用于再入飞行器制导与控制仿真的气动模型,并通过分析,得到该模型静稳定性、气动效率及气动控制特性等方面的结论。结合飞行器再入飞行的运动方程,选取平衡工作点,基于小扰动线性化模型得到系统特征根分布来分析其稳定性,发现固定姿态的滑翔飞行时系统有正半平面极点,需主动控制调节;为了分析机动性,提出了以星下点轨迹曲率求取CAV转弯半径的方法,可快速获取机动性评估与参考指标,结果表明,该模型具有较好的转弯机动能力。