推力向量控制方案及计算

本文归纳推力向量控制的主要方案,着重介绍摆动喷管、流体二次喷射方案的计算思路和结果.摆动喷管中的流场计算要考虑导弹偏摆对所产生的惯性力的影响;所得壁面压力畸变图说明,它是一个三维流场.在摆动喷管设计中要将铰链力减至最小,流体二次喷射的侧向力通过“等效实体模型”,用爆炸波的解来计算.     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

波音737NG飞机平尾内梁下蒙皮裂纹的修理

介绍了水平安定面内梁下蒙皮裂纹的成因以及发现裂纹后的修理方法，结合定检维修经验对裂纹损伤修理方案和经常出现的问题进行了分析总结，并给出了修理工期控制的建议。     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

Aerodynamics of smart flap under ground effect

Aerodynamic characteristics of two-dimensional smart flap under the ground effect have been assessed by a numerical simulation. In this process, a pressure-based implicit procedure to solve Navier–Stokes equations on a nonorthogonal mesh with collocated finite volume formulation is used. The boundedness criteria for this procedure are determined from the Normalized Variable Diagram (NVD) scheme. The procedure incorporates the k–ε eddy–viscosity turbulence model. Cantilever beam with uniformly varying load with roller support at the free end is considered for the configuration of the smart flap. The method is first validated against experimental data. Then, the algorithm is applied for turbulent aerodynamic flows around airfoil with smart and conventional flaps for different attack angle, flap angle and ground clearance where the results of two flaps are compared. The comparisons show that the quality of the solution is considerable.     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

超声速凹槽大涡数值模拟研究

在超声速燃烧室内常采用凹槽增强燃料与空气的混合,实现火焰稳定,本文采用大涡模拟方法对开式凹槽流场进行了数值模拟研究,计算采用Smagorinsky 亚网格模型模拟小尺度涡的作用.数值模拟结果给出了凹槽流动的自激振荡的发展过程,以及凹槽流动中拟序结构的演变过程,如涡的卷起、增长,涡与涡之间的合并、破碎等,计算得到的凹槽波动的峰值频率和理论结果一致.     

亚声速叶片与跨声速叶片的气动阻尼比较

为了研究叶轮机中叶片与流场流固耦合作用情况下的气动阻尼,分别以亚声速和跨声速转子叶片为例计算气动阻尼。根据对非定常气动力的分析,提出了一种与结构等效粘滞阻尼比对应的模态气动等效粘滞阻尼比的定义。采用弱耦合分域求解的算法,在线性范围内,计算并比较了跨声速叶片和亚声速叶片模态和振幅对模态气动阻尼比的影响,根据分布气动阻尼比研究压缩波对模态气动阻尼比的影响。研究结果表明这两类叶片的气动阻尼特性基本一致,所提参数对两类叶片的气动阻尼的影响基本相同。     

叶轮机械颤振稳定性的工程预测方法

通过求解雷诺平均N-S方程并采用影响系数法,对三个基本正交模态的三维振荡涡轮叶片绕流问题进行了研究。结果表明数值模拟所得非定常气动力与实验吻合较好;基于刚体运动假设和模态叠加法,得到了可用于叶轮机械设计阶段颤振稳定性评估的稳定性参数图/气动阻尼图,即所有可能的刚体运动及其相应气动阻尼的关系图;通过对稳定性参数图/气动阻尼图的分析表明,在一定情况下振型对颤振稳定性有重要影响,应将其作为颤振稳定性设计的重要参数之一。     

环截面管中的爆燃转爆震实验

为了实现在环截面爆震管封闭端同时点火,采用了先在预燃室中点火,再通过八路支管将火焰引入到爆震管封闭端,各个支管长度一样,因此可看成在环管封闭端多点同时点火.实验结果显示,在爆震管封闭端火焰汇聚形成激波点火,可在环管封闭端附近直接产生爆震波.在爆震管中安放扰流片时,流动阻力使爆震速度偏低,无扰流片时,爆震速度接近理论值.不加扰流片当量比在1.0左右,火焰速度会出现爆燃或爆震两种随机状态,当量比到1.1时可避免这种状况.