飞机蒙皮机器人化制造曲面分片算法研究

为实现飞机曲面机器人加工的自动轨迹规划,研究了基于模型几何特征的飞机曲面分片算法。通过分析飞机构件加工的工艺参数信息,以表面加工允许的最大曲率或最大偏角为阈值,提出基于近似曲率的三角网格模型分片方法。以三角网格中任意面片为起点,沿网格邻接关系向外拓展联接,形成若干近似平面化的模型分片结构,当超过阈值时则停止拓展,从而得到一整片曲面。通过对飞机CAD模型进行分片,发现采用本文提出方法可以保证分片结果的均匀性,为后期加工轨迹自动规划规划提供保障。     

基于反馈线性化的高速无人机自适应控制系统设计

高速无人机是典型的复杂非线性、参数不确定性系统,且各控制通道之间存在强耦合作用,这对飞行控制系统设计提出了严峻挑战。针对其非线性特性和耦合特性,采用精确反馈线性化理论将无人机动力学模型解耦为3个独立的子系统,即滚转、俯仰和偏航通道;应用模型参考自适应控制方法分别设计每个通道的姿态控制器。研究表明,上述线性化方法能够实现三通道解耦,所设计控制系统满足飞行控制性能要求,且对气动参数摄动和外部干扰具有较强的鲁棒性。     

拦截大气层内机动目标的自适应积分滑模制导律

针对大气层内机动目标拦截的末制导问题,提出了一种自适应积分滑模制导律。基于抑制弹目视线旋转的原则,设计了一种视线转率收敛速率可调的跟踪剖面,选取跟踪误差与其积分为状态变量,采用状态有限时间收敛的积分滑模面与快速趋近律推导得到了积分滑模制导律。为了处理未知的目标机动项,提出了一种自适应算法,对目标机动项上界的平方进行估计,构成了自适应积分滑模制导律,并证明了其有限时间收敛的特性,给出了各状态变量的收敛域。最后,将制导律转换成适用于大气层内拦截的形式。仿真结果表明,所提制导律能够精确拦截机动目标,剖面跟踪误差收敛速度快,过载分布均匀,能量消耗少,并具有良好的噪声特性,易于工程实现。     

对失控翻滚目标逼近的神经网络自适应滑模控制

针对失控航天器在空间中自由翻滚的情况,研究追踪器对失控翻滚目标逼近的位置和姿态六自由度耦合控制问题。建立追踪器与目标器相对运动的姿轨一体化动力学模型,设计追踪器逼近过程的标称轨迹和标称姿态。综合考虑系统不确定性和外部干扰,设计无抖振的神经网络自适应滑模控制器。将滑模控制与神经网络逼近相结合,采用径向基函数(RBF)神经网络对系统未知部分进行自适应逼近。由Lyapunov方法导出神经网络自适应律,通过自适应权重的调节保证整个闭环系统的稳定性。数值模拟实例说明了所设计的标称轨迹和标称姿态的合理性,同时验证了神经网络自适应滑模控制器的有效性。     

基于神经网络的机动飞行器自适应控制方法

针对机动飞行器强耦合性、快时变性以及高不确定性的问题,建立了六自由度刚体运动数学模型,按照时间尺度将姿态运动模型分为快变子系统和慢变子系统并分别设计动态逆控制律。然后给出了神经网络自适应控制器的设计方法,对神经网络的逆误差补偿原理、输入的选择、权值矩阵更新规则进行分析。通过算例进行六自由度仿真,证明本文方法的跟踪精度较高。     

Event-triggered adaptive control for attitude tracking of spacecraft

Plug-and-play technology is an important direction for future development of spacecraft and how to design controllers with less communication burden and satisfactory performance is of great importance for plug-and-play spacecraft. Considering attitude tracking of such spacecraft with unknown inertial parameters and unknown disturbances, an event-triggered adaptive backstepping controller is designed in this paper. Particularly, a switching threshold strategy is employed to design the event-triggering mechanism. By introducing a new linear time-varying model, a smooth function, an integrable auxiliary signal and a bound estimation approach, the impacts of the network-induced error and the disturbances are effectively compensated for and Zeno phenomenon is successfully avoided. It is shown that all signals of the closed-loop system are globally uniformly bounded and both the attitude tracking error and the angular velocity tracking error converge to zero. Compared with conventional control schemes, the proposed scheme significantly reduces the communication burden while providing stable and accurate response for attitude maneuvers. Simulation results are presented to illustrate the effectiveness of the proposed scheme.     

立式捏合机桨叶结构参数对混合釜流场影响的仿真分析

为揭示立式捏合机桨叶几何结构参数与混合釜流场之间的关系,以1 L两桨立式捏合机为研究对象,采用计算流体力学ANSYS Fluent 14.5软件对立式捏合机进行了三维模型仿真研究,分析了桨叶结构参数(桨桨间隙、桨叶螺旋角)的改变对混合物料挤压应力和剪切应力的影响。结果表明,增大桨桨间隙可减小桨叶对混合物料的挤压应力和剪切应力,空心桨螺旋角分别为40°、45°、50°,桨桨间隙由1.0 mm增加到3.0 mm,挤压应力、剪切应力分别平均减小了82.4%、57.23%;增大桨叶螺旋角可增大桨叶对混合物料的挤压应力和剪切应力,空心桨间隙分别为1.0、2.0 mm,桨叶螺旋角由35°增加到55°,挤压应力、剪切应力分别平均增加了92.8%、55.7%。     

无网格方法关于导数计算的程序验证

为了提高无网格方法对空间导数的数值计算能力,提出并论证了新的适用于直角坐标系、柱坐标系和球坐标系的空间导数无网格算法。基于数值解与理论解的对比分析,对数值误差和收敛性进行了后验评估。评估结果表明:该算法对函数和导数的估计均为2阶精度,支撑域尺度对数值误差的大小有一定影响,但不影响数值计算的精度等级。在离散尺度h为0.01的条件下,对所选函数及其导数的数值计算相对误差不大于0.65%。      

Matching mechanism analysis on an adaptive cycle engine

As a novel aero-engine concept, adaptive cycle aero-engines (ACEs) are attracting wide attention in the international aviation industry due to their potential superior task adaptability along a wide flight regime. However, this superior task adaptability can only be demonstrated through proper combined engine control schedule design. It has resulted in an urgent need to inves-tigate the effect of each variable geometry modulation on engine performance and stability. Thus, the aim of this paper is to predict and discuss the effect of each variable geometry modulation on the matching relationship between engine components as well as the overall engine performance at dif-ferent operating modes, on the basis of a newly developed nonlinear component-based ACE perfor-mance model. Results show that at all four working modes, turning down the high pressure compressor variable stator vane, the low pressure turbine variable nozzle, the nozzle throat area, and turning up the core-driven fan stage variable stator vane, the high pressure turbine variable nozzle can increase the thrust at the expense of a higher high pressure turbine inlet total tempera-ture. However, the influences of these adjustments on the trends of various engine components' working points and working lines as well as the ratio of the rotation speed difference are different from each other. The above results provide valuable guidance and advice for engine combined con-trol schedule design.     

典型复合材料结构固化变形仿真预测与控制验证

针对典型复合材料结构固化成型过程中变形难以控制的问题,本文对典型复合材料结构的固化变形进行仿真预测,从固化工艺和模具补偿两方面对固化变形加以控制和验证。固化工艺方面以各设计点变形数据为基础确定了最优固化工艺曲线,模具补偿方面提出了一种构件有限元模型自适应调整的方法,综合考虑固化工艺参数与模具型面补偿采用了一种基于全局补偿量的协同控制方法。结果表明,通过仿真模拟L形构件的固化变形误差为12.4%,借助响应面优化算法得到的L形构件最优固化工艺曲线其固化变形预测值与各试验设计点最大变形的最小值偏差不超过3.3%;T形加筋壁板有限元模型经自适应调整后,对于下表面与目标型面之间的偏差距离,数值模拟值与试验测量值的最大相对误差为17.20%。通过全局补偿量的协同控制方法对半筒形壁板的模具进行补偿,其固化变形最大值相比于传统单一模具型面补偿控制方法降低了接近90%。