Comparison of mesopause region meteor radar winds,medium frequency radar winds and low frequency drifts over Germany

During 2004 and 2005 measurements of mesospheric/lower thermospheric (80–100 km) winds have been carried out in Germany using three different ground-based systems, namely a meteor radar (36.2 MHz) at the Collm Observatory (51.3°N, 13°E), a MF radar (3.18 MHz) at Juliusruh (54.6°N, 13.4°E) and the LF D1 measurements using a transmitter (177 kHz) at Zehlendorf near Berlin and receivers at Collm with the reflection point at 52.1°N, 13.2°E. This provides the possibility of comparing the results of different radar systems in nearly the same measuring volume. Meteor radar winds are generally stronger than the winds observed by MF and especially by LF radars. This difference is small near 80 km but increases with height. The difference between meteor radar and medium frequency radar winds is larger during winter than during summer, which might indicate an indirect influence of gravity waves on spaced antenna measurements.     

Analysis of total visual and CCD V-broadband observations of Comet C/1995 O1 (Hale-Bopp): 1995–2001

We developed a general method for determination of water production rates from groundbased visual observations and applied it to Comet Hale–Bopp. Our main objective is to extend the method to include total visual magnitude observations obtained with CCD detector and V filter in the analysis of total visual magnitudes. We compare the CCD V-broadband careful observations of Liller [Liller, W. Pre-perihelion CCD photometry of Comet 1995 O1 (Hale-Bopp). Planet. Space Sci. 45, 1505–1513, 1997; Liller, W. CCD photometry of Comet C/1995 O1 (Hale-Bopp): 1995–2000. Int. Comet Quart. 23(3), 93–97, 2001] with the total visual magnitude observations from experienced international observers found in the International Comet Quarterly (ICQ) archive. A data set of ∼400 CCD observations covering about the same 6 years time span of the ∼12,000 ICQ selected total visual magnitude observations were used in the analysis. A least-square method applied to the water production rates, yields power laws as a function of the heliocentric distances for the pre- and post-perihelion phases. The average dimension of the nucleus as well as its effective active area is determined and compared with values published in the literature.     

碳/环氧复合材料两次表面镜基板研制

文章介绍了碳/环氧复合材料两次表面镜基板的结构与铺层、选材与成型工艺,性能测试等内容。     

8802超低频标准相位产生器

８８０２超低频标准相位产生器采用数字技术，用Ｄ／Ａ变换方法产生正弦信号，由单片机控制频率和相位，频率由晶振综合产生，相位可数字预置，频率准确度高至±５×１０￣（－６），相位准确度高至±０．０００２°。介绍了主要技术指标、工作原理、技术特点和误差分析等。     

ARM嵌入式处理器在智能仪器中的应用

介绍了一种基于ARM嵌入式处理器系统的智能仪器的硬件和软件设计方案,并结合uc/os-II嵌入式实时操作系统,给出了一套完整的任务调度和管理的方法,最后给出实例说明.     

Morphology and Frictional Characteristics Under Electrical Currents of Al203/Cu Composites Prepared by Internal Oxidation

Two AhO3/Cu composites containing 0.24 wt.% A1203 and 0.60 wt.% A1203 separately are prepared by internal oxidation.Effectsof sliding speed and pressure on the fi-ictional characteristics of the composites and copper against brass are investigated and compared.The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope (SEM) and energy dispersive X-ray spectrum (EDS).The results show that the wear resistance of the AI203/Cu composites is superior to that of copperunder the same conditions.Under a given electrical current,the wear rate of AI203/Cu composites decreases as the AleO3-content increases.However,the wear rates of the Al203/Cu composites and copper increase as the sliding speed and pressure increase under drysliding condition.The main wear mechanisms for AleO3/Cu composites are of abrasion and adhesion;for copper,it is adhesion,although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.     

一种摇臂式起落架的两种建模及结果对比

为了满足适坠性能要求,一种摇臂式起落架采用了双腔缓冲器。本文详细推导了拉格朗日方程下该起落架的动力学方程,并编程数值计算了四种状态的着陆性能。同时在Adams/Aircraft平台下建立了该起落架模型,通过编写子程序的方法实现了该双腔缓冲器的功能扩展。Adams/Aircraft平台下的仿真结果与数值计算的结果吻合较好,为起落架性能分析提供了很好的相互验证方法。     

基于CFD/CSD耦合的叶轮机叶片失速颤振计算

为了研究叶轮机叶片的失速颤振特性,发展了一种计算流体力学与计算结构力学(CFD/CSD)时域耦合方法。该方法通过每一物理时刻CFD和CSD的循环迭代实现了耦合计算。在CFD分析中,采用鲁棒性较好的空间离散格式AUSM+-UP,并基于延迟脱体涡模型(DDES)模拟了带分离流动。在结构分析中,通过模态法构建了旋转叶片动力学方程并运用杂交多步方法进行求解。以孤立转子Rotor37为例,计算了不同工况下流场总体与细节参数,与实验结果的对比验证了CFD算法的精度。对某转子叶片进行了颤振特性研究,计算所得的广义位移时间响应曲线表明该叶片在近失速工况下会发生失速颤振,其表现形式为一阶弯曲模态发散且各阶模态之间不耦合。分析表明,流场不稳定和非定常效应是引起失速颤振的关键因素,同时折合频率的降低也会导致原本气动弹性稳定的叶片发生失速颤振。     

M40/4211 复合材料层合板铣削加工试验

通过分析碳纤维复合材料的性能特点及对切削加工性能的影响,提出了铣削刀具材料和几何结构形式的选用原则,介绍了几种适于碳纤维复合材料铣削的加工刀具。针对碳纤维复合材料中常用的M40/4211复合材料层合板进行加工缺陷试验和切削试验,总结出影响M40/4211复合材料层合板加工质量的因素及规律,得到每种刀具加工M40/4211复合材料层合板的最佳加工参数,较高的切削速度配合恰当的进给速度可以有效提高M40/4211复合材料层合板的加工质量和加工效率。