PSK转换法产生直序扩频MSK信号研究

通过 PSK转换法产生 MSK信号的数学模型的进一步推导和计算机仿真 ,研究了不同长度的扩频码对延时相干解调扩频 MSK信号的影响。然后进行了 PSK转换法产生扩频 MSK信号的系统实验     

基于TDRSS的高速数传信号载波捕获及跟踪算法研究

以TDRSS数传系统为研究背景,针对TDRSS数传信号的特点,以实现高速8PSK调制信号的载波同步与跟踪为研究前提。提出了一种采用二叉树(BinarySearchTree)频率搜索方法实现捕获及采用平均"滑动窗"递推最小二乘(RLS)一步预测方法实现频率跟踪的算法,并针对此方法进行了理论推导和蒙特卡洛(MonteCarlo)仿真。结果表明:该方法适用于全数字高速数传8PSK调制信号接收系统,同时也可移植、推广至全数字雷达接收机中。     

YH-1火星探测器设计及研制进展

介绍了中国首颗YH-1火星探测器的任务功能、组成和主要技术指标。给出了探测器设计中的火星探测超低温适应、深空探测自主姿态确定与控制、超远距离通信、休眠唤醒和剩磁控制等关键技术,以及相应的解决途径。试验和验证结果表明：YH-1火星探测器的设计满足火星探测特殊环境的任务要求。其设计和试验技术可直接用于我国其他深空探测项目,为后续深空探测积累了经验。     

水杨醛缩－5－碘－8－氨基喹啉新西夫碱试剂的合成及其分析应用研究──分光光度法测定痕量镓

本文介绍了水杨醛缩－５－碘－８－氨基喹啉新西夫碱的合成、提纯与鉴定。特别对其性质及其与镓金属离子显色反应的光度特性作了研究，其配合物３．４９×１０４Ｌ·ｍｏｌ（－１）·ｃｍ（－１）．     

空间用9Cr18 钢PIII 复合离子注入表面改性工艺研究

采用等离子体浸没离子注人(PⅢ)技术对9Cr18轴承钢表面进行了双注入及共注入Ti+N工艺处理.测试了处理前后试样的显微硬度及真空摩擦因数,并表征分析了表面磨损形貌.结果表明:处理后试样的显微硬度都有大幅提高,最大增幅达68.7％；表面真空摩擦因数由0.15下降到0.08；磨斑尺寸及粗糙度分别减少了54.4％和37.4％.双注入与共注入方式在相同参数下,双注入处理后的试样表面综合性能更加优异.     

基于PSK调制的数字通信信号仿真分析技术

基于PSK调制的数字通信系统在无线通信工程实践中有着广泛的应用，由于受到各种条件的限制，从实际工程系统接收到的PSK数字通信信号在教学科研中不易获得，而PSK调制仿真数据则可以自己产生。在掌握通信原理和仿真技术的基础上利用Matlab实现对BPSK、DPSK、QPSK、DQPSK、8PSK、π/4-DQPSK、OQPSK等数字通信信号源的模拟仿真，可对调制体制、工作频率、传输码率、采样频率、信道特征等参数进行灵活设置，并按要求生成规定格式的DAT数据文件，可作为调制方式识别软件的训练和测试样本。结合模方谱、平方谱、四次方谱、八次方谱等谱线参数特征，同时结合星座图和眼图进行基于PSK调制的数字通信信号的调制体制判别和验证。     

Landsat 8地表温度产品验证与分析

Landsat系列卫星热波段具有60~120m的空间分辨率，对各种环境监测起到了重要的作用。随着Landsat系列卫星在全球范围内地表温度（land surface temperature，LST）产品的发布，其验证工作也随之展开，然而对于长时间序列的精度验证工作仍然缺乏。以黑河流域中游为研究区，利用研究区内湿地站（SD）、戈壁站（GB）和大满超级站（CJZ）三个气象站的地面测量数据对2013-2016年清晰无云的31景Landsat 8地表温度产品进行了验证与分析，并将Landsat 8地表温度产品与广泛使用的普适性单通道算法（JMS）反演结果进行了对比。结果表明，Landsat 8地表温度产品与普适性单通道算法反演结果精度均较高，在各个站点处R2均优于0.949。基于所有站点分析，Landsat 8地表温度产品精度稍高于普适性单通道算法反演结果。     

Effect of Isothermal Forging on the Microstructure and Mechanical Properties of Mg-8Gd-3Y-0.5Zr Alloy

Aiming at the problems of poor plastic forming ability， narrow forging temperature range， and strain rate sensitivity of rare earth magnesium alloys， a study on the microstructure and mechanical properties of Mg-8Gd-3Y-0.5Zr alloy with different isothermal forging processes is carried out. The microstructure and properties of the alloy in the as-cast， isothermal forged， and post-aging states after forging are studied with optical microscope (OM)， scanning electron microscope (SEM)， and tensile testing. The results show that significant dynamic recrystallization occurs during the isothermal forging process， a fine equiaxed grain structure is formed， and the mechanical properties of the alloy are greatly improved. When the isothermal forging temperature is 460 ºC and the strain rate is 0.02 s－1， the alloy structure performance is the best， the room temperature tensile yield strength (TYS) is 218 MPa， the ultimate tensile strength (UTS) is 299 MPa， and the fracture elongation (FE) is 19.2%. When the alloy is post-forging artificial aged， the α-Mg matrix is dispersed， the Mg5(Gd，Y) phase is precipitated， the UTS of the alloy is increased to 392 MPa， and the FE is reduced to 12.0%.     

Hardware qualification for scientific ballooning missions

The European Stratospheric Balloon Observatory (ESBO) initiative aims at simplifying the access to stratospheric balloon missions. We plan to provide platforms and support with instrument design in order to support scientists. During the design process, the inevitable question of qualification for the harsh flight conditions arises. Unfortunately, there is no existing standard for qualification of stratospheric ballooning hardware. Thus, we developed a qualification procedure for use within ESBO and similar projects.In this paper, we present our analysis of the environmental conditions in the stratosphere. While conditions at typical balloon float altitudes are similar to the space environment, there are also some relevant differences. For example, the thermal environment is dominated by radiation and thermal conduction, but the remaining atmosphere still supports a certain amount of convection. The remaining atmospheric pressure in the stratosphere also leads to reduced arcing distances. Vibrational loads are far less than for space missions, but quasi-static or shock loads may occur. The criticality of radiation increases with mission duration.Based on the environmental conditions, we present the qualification procedures for ESBO, which are based on the European Cooperation for Space Standardization (ECSS) standards for space systems. Overtesting against too high requirements leads to overengineering, driving mission cost and mitigating the advantages of balloons over space missions. Therefore, we modified the ECSS standards to fit typical scientific ballooning missions over several days at altitudes up to 40 km. Furthermore, we analyzed design rules for space systems with regard to their relevance for scientific ballooning, including material and component selection. We present the experience from the hardware qualification process for the ESBO prototype STUDIO (Stratospheric UV Demonstrator of an Imaging Observatory). Even though boundary conditions are different for each individual mission, we aimed for a broader approach: We investigated more general requirements for scientific ballooning missions to support future flights.     

Integration of Landsat-8 and Sentinel-1 dataset to extract geological lineaments in complex formations of Tepal mountain area,Shahrood, north Iran

Recently, the detection and extraction of geological lineaments have become an essential analytical technique to find relationships between the characteristics and occurrence of hydrogeology, and tectonic studies. The use of remote sensing, with the progressive development of image enhancement techniques, provides an opportunity to produce more reliable and comprehensive lineament maps. In this paper, semi-automatic approach based on Landsat 8 and Sentinel 1 radar data is proposed for lineaments extraction and validation. The combined method of linear filtering and automatic line module ensures a high degree of accuracy resulting in a lineament map. Based on identified lineaments, Sentinel1 is more capable of detecting edges than Landsat8, but the primary orientation lineaments extracted from Landsat8 and Sentinel1 were different. So, by combining band6 of Landsat8, and VV and VH polarization of Sentinel1, the area lineaments were extracted with high accuracy. Rose diagram showed the extracted lineaments' orientation is in good compliance with the region's existing faults. Also, the formations' lineament length density has good consistent with the density of the faults in the geological map.