阳极氧化膜厚度对TB8钛合金表面特性及其粘结性能的影响

采用以酒石酸钠为主盐的电解体系对TB8钛合金进行阳极氧化,研究阳极氧化膜厚度对TB8钛合金表面特性及其与环氧树脂粘结性能的影响。采用SEM、XRD和EDS分析了阳极氧化膜的微观形貌和晶体结构,采用角接触测量仪和三维视频显微镜分别对阳极氧化膜的表面润湿性和粗糙度进行测量。研究了不同厚度TB8钛合金阳极氧化膜的粘结性能与表面形貌、相组成、润湿性及粗糙度的关系。结果表明:采用以酒石酸钠为主盐的电解体系对TB8钛合金进行阳极氧化处理,氧化时间为15 min,电压为1~30 V时,能够在钛合金表面形成一层1~4μm厚的阳极氧化膜;氧化膜主要由金红石型和锐钛型TiO₂混合晶体组成,其表面具有微纳多孔的粗糙结构;随着厚度的增加,阳极氧化膜对水的润湿性能逐渐增强。当氧化膜厚度为3μm时,可获得最大粘结强度为19.6 MPa,相对于母材提高了88.5%,同时,水接触角为43.2°,相对于其母材减少了56.1%;粗糙度为2.14μm,相对于母材提高了137.8%。     

三种钻头钻削CFRP轴向力的时变曲线及预测

采用二刃、三刃双锋角钻头和圆弧形钻头钻削CFRP单向板,研究钻削过程中轴向力时变曲线的特征,并探索用预测轴向力时变曲线上的关键拐点的方法来构建预测轴向力时变曲线模型。结果表明:三刃双锋角钻头的轴向力时变曲线最为稳定,钻削过程最为稳定;轴向力最大的是三刃双锋角钻头,其次是圆弧形钻头,最小的是二刃双锋角钻头,说明二刃双锋角钻头适合钻削CFRP;用预测轴向力时变曲线上的关键拐点的方法构建的轴向力时变曲线可以很好地预测双锋角钻头轴向力时变曲线。     

CFRP复合材料超声振动套孔分层抑制机理分析

针对碳纤维增强复合材料在传统钻孔过程易出现分层缺陷,采用金刚石空心套刀和超声振动加工技术进行了CFRP超声振动套孔分层抑制机理分析。理论分析了传统麻花钻钻孔与金刚石套刀普通套孔过程的分层机理及评价,超声振动套孔对分层抑制的机理,并且进行了实验验证。结果表明:相比于CFRP普通套孔,超声振动套孔能够有效提高套刀切削性能和排屑效果,降低钻削力12.5%～19.2%,抑制切屑粉尘黏附套刀和料芯堵塞套刀,抑制CFRP分层缺陷形成,改善孔表面质量。     

八面钻超声振动钻削钛合金出口毛刺形成机理

钛合金在传统麻花钻常规钻孔后,会产生较大的孔出口毛刺,这将导致孔出口去毛刺困难且影响紧固件装配质量。本文引入一种八面钻新刃型刀具,并利用超声振动钻削技术,进行了八面钻超声振动钻削钛合金出口毛刺形成的基础理论和试验研究。理论分析了普通钻削和超声振动钻削的出口毛刺形成过程以及超声振动钻削的出口毛刺降低机理,同时试验验证了超声振动钻削的出口毛刺降低效果。结果表明:相比于钛合金普通钻削,超声振动钻削极大地提高了钻头刀具的切削能力,分别降低了钻削力16%~20%、切削温度18%~21%和出口毛刺高度82%~89%,有效降低了装配过程的去毛刺困难和生产成本。     

缝线粗细对复合材料面内弹性模量的损伤分析

建立了以碳纤维八枚五飞经面缎为基布,以不同粗细缝线的三维有限元模型。分别预报了缝线植入处基布全部损伤和部分损伤两种状况的弹性模量,较粗的缝线使得复合材料的拉剪弹性模量降低,较细的缝线对面内弹性模量影响较小;与未缝合相比,不同直径的缝线的模量变化在9.6%之内。此外,实验结果比有限元预报值大,但缝线粗细对复合材料面内弹性模量影响规律两者结果一致。     

Land use/land cover classification using time series Landsat 8 images in a heavily urbanized area

It is of great significance to timely, accurately, and effectively monitor land use/cover in city regions for the reasonable development and utilization of urban land resources. The remotely sensed dynamic monitoring of Land use/land cover (LULC) in rapidly developing city regions has increasingly depended on remote-sensing data at high temporal and spatial resolutions. However, due to the influence of revisiting periods and weather, it is difficult to acquire enough time-series images with high quality at both high temporal and spatial resolution from the same sensor. In this paper we used the temporal-spatial fusion model ESTARFM (Enhanced Spatial and Temporal Adaptive Reflectance Fusion Model) to blend Landsat8 and MODIS data and obtain time-series Landsat8 images. Then, land cover information is extracted using an object-based classification method. In this study, the proposed method is validated by a case study of the Changsha City. The results show that the overall accuracy and Kappa coefficient were 94.38% and 0.88, respectively, and the user/producer accuracies of vegetation types were all over 85%. Our approach provides an accurate and efficient technical method for the effective extraction of land use/cover information in the highly heterogeneous regions.     

Integrating aeromagnetic data and Landsat-8 imagery for detection of post-accretionary shear zones controlling hydrothermal alterations: The Allaqi-Heiani Suture zone,South Eastern Desert,Egypt

The Arabian-Nubian Shield (ANS) underwent a regional carbonation event with CO₂ fluxes derived from the mantle and circulated along post-accretionary shear zones, thus affecting the redistribution of gold mineralization. Formerly, the analyses of remotely-sensed data have suggested regions of gold mineralization linked to the post-accretionary structured framework, but the results were insufficient for detailed prospecting in the ANS. In this research, aeromagnetic data and Landsat-8 imagery were integrated for delineating new high potential zones of gold mineralization in the Allaqi-Heiani Suture (AHS) zone, the ANS, South Eastern Desert (SED) of Egypt. Aeromagnetic data were enhanced using the Center for exploration targeting (CET) grid enhancement technique to detect the main structures that control hydrothermal alterations in the study area. Principal Component Analysis (PCA) technique and ratios of spectral bands were applied to Landsat-8 data for mapping zones of hydrothermal alteration associated with gold mineralization. The traced structural elements from RTP, CET and Landsat-8 maps were statistically plotted and interpreted using rose diagrams. These diagrams indicated that the NW and NE trends are the most dominant in the RTP map and that the intersection zones obtained from the CET analysis are aligned along the NW-oriented trend. While the NNW, WNW and NE trends were the most dominant ones in Landsat maps. The integration of the results indicates several new high potential zones of gold and Cu/Ni mineralization types, which are mostly concentrated at the western part of the AHS zone. The hydrothermal alteration zones and associated gold mineralization are strongly linked to NW, NE, E-W and WNW trending lineaments. The approach used in this study can be applied to other parts of the ANS and other regions with similar geological conditions around the world.     

K8飞机非加压供氧系统研究

介绍Ｋ８飞机在１３．１ｋｍ高度上使用加压供氧系统的理论计算与试验结果。通过理论计算与试验结论，证明在升限１３．１ｋｍ高度上配备非加压供氧系统是完全可行的。     

K8E项目的管理控制评述

K8E工程是中国首次整机成套生产技术出口项目。其涉及面广、内容层次深、执行周期长、政治影响大、项目管理水平高。本文用项目的管理控制理论，对K8E工程项目的若干管理行为进行分析和评述。