AA2024铝合金搅拌摩擦焊接头特性研究

对6 mm厚AA2024-T4铝合金搅拌摩擦焊接头特性进行了研究。通过拉伸试验,得到了应力-应变曲线。用光学显微镜、显微硬度仪以及扫描电镜对焊接接头进行了金相分析、硬度测试以及断口分析。结果表明：试件断裂属于韧性断裂;断裂发生在前进侧热机影响区/热影响区的过渡区;当搅拌头转速为800 r/min,焊接速度为100 mm...     

异种状态TC4 钛合金电子束焊接性能分析

针对相对疏松的铸造钛合金和相对密实的锻造钛合金的焊接问题,开展了两种状态的TC4钛合金电子束焊接工艺研究,对比了不同焊接参数对焊接质量的影响。研究结果表明,采用方波扫描可以较好地实现铸造钛合金与锻造钛合金的连接,焊缝成形良好,内部无缺陷;焊接接头力学性能分析表明,拉伸断裂位置全部在铸件母材区一侧。实焊结果证明,电子束焊接可以实现异种状态TC4钛合金焊接的工程化应用。     

In706合金长时组织稳定性研究

In706合金经650℃×500h,1000h长期时效处理后,测定显微组织和力学性能.试验结果表明,In706合金组织稳定,高温持久断裂寿命、塑性亦较高,可用于航空发动机涡轮盘、轴类转动部件.     

5A90铝锂合金型材折斜角成形性能的试验研究

型材一次折斜角成形是航空零件制造工艺的重要方法之一。本文通过新研制的5A90铝锂合金型材折斜角成形试验的研究，得到了极限开斜角和闭斜角值，为新机的设计及生产工艺提供了重要的指导依据。     

Formability enhancement in hot spinning of titanium alloy thin-walled tube via prediction and control of ductile fracture

The damage and fracture in hot spinning of titanium alloy is a very complex process under the combined effects of microstructure evolution and stress state. In this study, their dependences on processing parameters were investigated by an integrated FE model considering microstructure and damage evolution, and revealing the effects of microstructure and stress states on damage evolution. The results show that the inner surface of workpiece with the largest voids volume fraction is the place with...     

Prediction of forming limit curve （FLC） for AI-Li alloy 2198-T3 sheet using different yield functions

The Forming Limit Curve （FLC） of the third generation aluminum-lithium （Al-Li） alloy 2198-T3 is measured by conducting a hemispherical dome test with specimens of different widths. The theoretical prediction of the FLC of 2198-T3 is based on the M-K theory utilizing respectively the von Mises, Hill＇48, Hosford and Barlat 89 yield functions, and the different predicted curves due to different yield functions are compared with the experimentally measured FLC of 2198-T3. The results show that though there are differences among the four predicted curves, yet they all agree well with the experimentally measured curve. In the area near the planar strain state, the predicted curves and experimentally measured curve are very close. The predicted curve based on the Hosford yield function is more accurate under the tension-compression strain states described in the left part of the FLC, while the accuracy is better for the predicted curve based on Hill＇48 yield function under the tension-tension strain states shown in the right part.     

Prediction of forming limit curve (FLC) for Al-Li alloy 2198-T3 sheet using different yield functions

The Forming Limit Curve (FLC) of the third generation aluminum-lithium (Al-Li) alloy 2198-T3 is measured by conducting a hemispherical dome test with specimens of different widths. The theoretical pred...     

Wire electrochemical machining with axial electrolyte flushing for titanium alloy

Titanium and its alloys have found very wide application in aerospace due to their excellent characteristics although their processing is still a challenge. Electrochemical machining is an important issue in the fabrication of titanium and titanium alloys. Wire electrochemical machining (WECM) is mainly used for workpiece cutting under the condition of different thickness plates. It has a great advantage over wire electro-discharge machining, which is the absence of heat-affected zone around the cutting area. Moreover, the wire electrode in WECM could be used repetitively because it is not worn out. Thus, much attention has been paid to WECM. The effective way of removing electrolysis products is of importance to WECM. In this paper, the axial electrolyte flushing is presented to WECM for removing electrolysis products and renewing electrolyte. The Taguchi experiment is conducted to optimize the machining parameters, such as wire feedrate, machining voltage, electrolyte concentration, etc. Experimental results show that WECM with axial electrolyte flushing is a promising issue in the fabrication of titanium alloy (TC1). The feasibility of multi-wire electrochemical machining is also demonstrated to improve the machining productivity of WECM.     

5083铝合金力学性能的球压痕法检测研究

介绍了微压痕法在航空铝合金材料力学性能检测的研究.采用球形压头通过多级循环加载方法得到了5083铝合金材料压痕深度与载荷的关系,将微压痕数据输入经过充分训练的人工神经网络模型,计算出材料力学性能参数和材料应力应变曲线,对压痕法测量得到的材料真应力应变曲线与拉伸试验得到的结果进行了比较.     

双层板激光焊接/ 超塑成形数值模拟及工艺研究

选取TC4 钛合金四层板加强结构中双层板为研究对象,采用激光穿透焊接工艺代替传统超塑成

形/ 扩散连接(SPF/ DB)工艺中涂止焊剂连接。借助ABAQUS 有限元分析软件对超塑成形过程进行分析,得到

优化的压力-时间(p-t)曲线,作为双层板超塑成形过程的气压加载曲线,进行实验验证。结果表明:成形后零

件壁厚分布均匀,焊缝处无撕裂现象,与有限元模拟结果保持一致;用此新工艺代替传统SPF/ DB 工艺中的止

焊剂具有可行性。