Effect of tube-electrode inner diameter on electrochemical discharge machining of nickel-based superalloy

Nickel-based superalloys are widely employed in modern aircraft engines because of their excellent material characteristics, particularly in the fabrication of film cooling holes. How-ever, the high machining requirement of a large number of film cooling holes can be extremely chal-lenging. The hybrid machining technique of tube electrode high-speed electrochemical discharge drilling (TEHECDD) has been considered as a promising method for the production of film cooling holes. Compared with any single machining process, this hybrid technique requires the removal of more complex machining by-products, including debris produced in the electrical discharge machin-ing process and hydroxide and bubbles generated in the electrochemical machining process. These by-products significantly affect the machining efficiency and surface quality of the machined prod-ucts. In this study, tube electrodes in different inner diameters are designed and fabricated, and the effects of inner diameter on the machining efficiency and surface quality of TEHECDD are inves-tigated. The results show that larger inner diameters could effectively improve the flushing condi-tion and facilitate the removal of machining by-products. Therefore, higher material removal efficiency, surface quality, and electrode wear rate could be achieved by increasing the inner diam-eter of the tube electrode.     

TC4钛合金激光焊中工艺参数对气孔生成量的影响

文摘研究了TC4钛合金激光焊接在平焊、横焊两种位置下工艺参数对气孔生成量的影响。结果表明:平焊时,气孔生成量随激光功率、离焦量的增大先减小后增大,随焊接速度的增大先增大后减小;横焊时,气孔生成量随激光功率的增大而增大,随焊接速度的增大而减小,随离焦量的增大先减小后增大。利用正交试验方法得到的优化工艺参数进行焊接,气孔生成量大幅减少,在两种位置下均可得到内部质量良好的焊缝。     

开式整体叶盘四坐标插铣开槽粗加工刀位轨迹规划

提出在开式整体叶盘的粗加工阶段,采用插铣加工代替传统的五轴数控加工点铣和侧铣,实现高效加工.提出将自由曲面蜕变为直纹面,将复杂自由曲面粗加工问题转化为简单的直纹面粗加工问题.这种方法的加工效率比传统加工方法提高约60%以上.     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.     

页轮干式磨削Ti6Al4V合金

进行了Ti6A14V合金锆刚玉页轮和碳化硅页轮的磨削性能试验研究,分析了磨削用量对磨削力、磨削温度和磨削表面完整性的影响。磨削力通过KISTLER9265B测力仪测定,磨削表面温度由NIUSB-621X信号采集系统测得,磨削表面形貌和金相组织由HiroxKH-7700型体视显微仪和Quanta200型扫描电镜（SEM）观察,表面粗糙度由Mahr Perthometer M1粗糙度仪测得,表层显微硬度通过HVS—1000硬度计测定。研究结果表明：页轮磨削钛合金工件表面没有发生烧伤现象,磨削热影响区厚度小于50μm,锆刚玉页轮比碳化硅页轮更适合干式磨削钛合金。     

基于宏程序的外球面粗精加工

目前,小内存的数控机床仍然是我国机床的主流,使加工程序变得简洁,对实际加工有着很重要的意义.宏程序的应用可以大大简化编程,本文通过实例介绍了数控铣削加工外球面的宏程序.     

三维四向编织复合材料等效热特性数值分析和试验研究

 采用“米”字型枝状胞体有限元模型和试验方法对三维四向编织复合材料的整体等效热膨胀系数和等效热传导系数进行了分析并将计算结果和试验值进行了比较。研究表明枝状胞体模型能较为真实的反映三维四向编织复合材料的结构构形;有限元方法在分析热膨胀、热传导方面具有较好的精度;三维四向编织复合材料编织方向的热膨胀系数随着纤维体积比的增加而减小,随着编织角的增加而减小;热传导系数随着纤维体积比的增加而增大,随着编织角的增大而增大。     

数控电解加工整体叶轮的关键技术

以平行直纹型面的数控展成电解加工为例，对数控电解加工整体叶轮的主要关键技术，包括成形规律、展成运动、数控编程、阴极设计制造、机库及多轴联动数控系统、典型叶轮加工工艺逐一进行了介绍。     

飞机整体结构件加工变形的有限元模拟与试验研究

在模拟淬火、拉伸过程获得含有初始残余应力的预拉伸板材以及模拟单齿切削过程获得切削载荷的基础上,提出并采用接力算法,对一航空整体结构件的材料铣削过程进行有限元仿真,同时进行了试验研究.结果表明,有限元模拟的整体结构件的变形与试验具有一致性,从而证明提出的整体结构件加工仿真关键技术的可行性,避免了为研究加工变形而进行的繁琐的试错法.     

无压浸渗制备Si3N4／Al复合材料的界面反应研究

研究Si3N4多孔预制体的表面氧化程度对无压浸渗制备Si3N4/Al复合材料界面反应以及复合材料性能的影响是复合材料优化设计的基础.不同氧化程度的Si3N4多孔预制体在相同的浸渗工艺下无压浸渗制得Si3N4/Al复合材料,利用EDS,XRD和洛氏硬度计分别测定陶瓷多孔预制体的成份,复合材料的相组成和硬度.结果表明:Si3N4/Al复合材料组成相包括Al,Si3N4,AlN以及少量的Si,Mg2Si,MgO,MgAl2O4;随着氧化程度增加,复合材料内AlN相减少,MgO含量增加,并逐渐出现MgAl2O4相;复合材料的硬度随预制体的氧化程度增加而线性下降;预制体的氧化造成Si3N4和Al之间的反应减弱是硬度下降的重要原因.