碱性体系锌—镍合金电沉积的研究

本文介绍了一种新型的碱性体系锌-镍合金电镀工艺。本工艺镀层光亮、镀液稳定、组成简单及维护方便,能在很宽的工艺范围下能镀出含镍量为11～15％的锌-镍合金。镀层具有高耐蚀性及低氢脆性。对电沉积机理也作了必要叙述。     

飞机V型外倾双垂尾载荷校准技术

根据垂尾载荷校准及建模需求,对飞机V型外倾双垂尾结构受载情况进行了分析和简化,确定了校准试验载荷,研制了垂尾载荷校准试验专用龙门梁架。采用液压协调加载技术,完成了外倾双垂尾载荷校准试验,建立了满足测载要求的载荷模型。此种方法充分利用了左右垂尾外倾、双垂尾之间空间较大的特点,对左右垂尾对称施加向外的单点、多点载荷,加载载荷侧向分量左右自平衡,垂向分量依靠飞机自身重量即可平衡,飞机不需要复杂的固定与约束。试验中采用先搭建龙门框架,再停放飞机的方法,降低了试验风险、加快了试验进度,取得了良好的试验结果,对其他此类结构的载荷校准具有一定的借鉴作用。     

Atmospheric reentry hemisphere prediction for prograde orbits using logical disjunction

A unique logic-based algorithm for atmospheric reentry hemisphere prediction is presented for spacecraft in low-eccentricity, prograde low Earth orbits at altitudes of 300 km and lower. Using two-line element (TLE) data for initial orbit conditions, coupled with coarse estimates for spacecraft aerodynamic characteristics, the algorithm relies on logical disjunction operations based on a dual analysis of histogram and two-weighted Gaussian probability density function (PDF) fits of predicted reentry latitude data. The algorithm requires the execution of a series of parametric simulations to determine the reentry hemisphere for variations in spacecraft aerodynamic coefficients and drag reference area. When implemented, the algorithm yields accurate hemisphere predictions on average 15 days from reentry as demonstrated by historical reentry cases from 1979 to 2018. All reentry cases were selected to demonstrate the algorithm’s ability to deliver accurate reentry hemisphere predictions for spacecraft with varying physical size and mass, and reentering during different periods of solar cycle activity.     

DME Interference mitigation for L-DACS1 based on system identification and sparse representation

L-band digital aeronautical communication system 1 (L-DACS1) is a promising candi-date data-link for future air-ground communication, but it is severely interfered by the pulse pairs (PPs) generated by distance measure equipment. A novel PP mitigation approach is proposed in this paper. Firstly, a deformed PP detection (DPPD) method that combines a filter bank, correlation detection, and rescanning is proposed to detect the deformed PPs (DPPs) which are caused by mul-tiple filters in the receiver. Secondly, a finite impulse response (FIR) model is used to approximate the overall characteristic of filters, and then the waveform of DPP can be acquired by the original waveform of PP and the FIR model. Finally, sparse representation is used to estimate the position and amplitude of each DPP, and then reconstruct each DPP. The reconstructed DPPs will be sub-tracted from the contaminated signal to mitigate interference. Numerical experiments show that the bit error rate performance of our approach is about 5 dB better than that of recent works and is closer to interference-free environment.     

热处理对FeCo-2V-0.5Cr软磁合金力学与磁学性能的影响

针对FeCo-2V-0.5Cr软磁合金,研究了真空热处理时间对其微观组织结构、力学与磁学性能的影响规律,发现在800℃下热处理时间为2h左右时,合金的抗拉强度和延伸率达到最佳,同时仍保持良好的软磁性能,抗拉强度、延伸率以及矫顽力分别为867.8MPa、10.4%以及2.0Oe。进一步对该合金进行附加磁场下的真空热处理,重点研究了合金的交流损耗与矫顽力随附加磁场方式包括磁场撤除温度与磁场下保温时间的变化规律,发现适当的磁场热处理对合金相关力学性能影响不大,但由于合金中产生了单轴各向异性而使合金矫顽力进一步降至1.6Oe。     

蒙皮零件拉伸粗晶的控制研究

针对民机2014材料(材料规范L164/L165/L167)、某型机2B06OB材料拉伸成形过程中出现的粗晶缺陷,进行了大量的工艺试验,分析并查找出粗晶产生的原因,摸清材料性能,并提出最终解决方案。     

新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性试验研究

随着新型Al-Li-Cu-Mg合金蒙皮在航空航天等高技术工业的应用日益广泛,新型Al-Li-Cu-Mg合金蒙皮拉伸成形特性已成为新型Al-Li-Cu-Mg合金板蒙皮成形质量精确控制以及蒙皮设计迫切需要解决的关键问题.因此,首先获得了新型T8态Al-Li-Cu-Mg合金的最佳热处理工艺参数;其次,采用试验方法,研究了不同热处理状态的拉伸成形过程,揭示了新型Al-Li-Cu-Mg合金板材的拉伸成形特性.发现通过固溶处理,后续时效能够显著提高新型T8态Al-Li-Cu-Mg合金材的拉形能力;在新型A1-Li-Cu-Mg合金板材拉形过程,桔皮现象主要出现在补拉阶段,蒙皮悬空区应变值＞0.0215时,板材表面将出现桔皮,且与材料热处理状态无关.     

基于支持向量机和粒子群算法的钛合金铣削加工参数优化

钛合金材料在加工过程中受铣削力影响易于产生变形而影响加工效果,为保证加工质量,提高生产效率及降低加工成本,研究切削加工参数的合理选择非常重要.对钛合金材料Ti6Al4V铣削加工进行有限元数值计算,结合试验设计方法构建了基于支持向量机的切削力预测模型,以材料去除率为优化目标,提出了一种基于支持向量机和粒子群算法的优化方法,对钛合金铣削加工参数进行了优化.结果表明,该方法准确、高效、可行,为钛合金加工工艺参数优化提供一种新的方法,具有良好的推广价值.     

TC4钛合金静止轴肩和传统搅拌摩擦焊的温度场对比

基于有限元软件ABAQUS对6mm厚的TC4钛合金传统及静止轴肩搅拌摩擦焊温度场进行了有限元模拟.结果表明,对比传统搅拌摩擦焊接,静止轴肩搅拌摩擦焊接具有较小的高温区,前进方向上具有较大的温度梯度,厚度方向上呈现柱状椭球形分布,上、下表面温度峰值差异较小,具有重叠性较好的热循环曲线.     

基于断口分析的钛合金轮内部缺陷损伤容限

为进行某轮损伤容限设计,开展了裂纹扩展断口分析和仿真分析研究。由断口分析可知:疲劳源为一处内部自然缺陷;依据疲劳辉纹确定了裂纹扩展速率;在裂纹长度为2 mm附近,裂纹扩展速率明显增大,为第一、第二加载阶段转换区域;裂纹稳定扩展区裂纹长度与裂纹扩展速率呈双对数线性关系;应用列表梯度法和Paris公式法反推了第二加载阶段的疲劳寿命,与该阶段实际循环次数的最大误差是163%。裂纹稳定扩展阶段裂纹扩展仿真值与断口反推值吻合;非稳定扩展阶段仿真值与断口反推值的最大误差为-215%;基于以上研究,合理确定了某离心轮内部裂纹表面扩展停机检测周期。该类轮非稳定、失稳扩展阶段寿命占内部裂纹表面扩展阶段寿命的比例达248%~357%,因此准确计算具有重要意义。