Performance analysis and application on Ti-6Al-4V of micro-forging system

Micro-forging (MF) is a novel surface modification technology which is capable of smoothening and strengthening the workpiece surface simultaneously. Based on analysis of the mechanism and energy conversion of micro-forging process, an electromagnetically driven micro-forging system is developed. To further grasp the kinetic characteristic of the equipment, a simulation model is established and its accuracy is verified. With the help of simulation and experimental results, we propose an input voltage optimization method, which drives the micro-forging head moving in a uniform and stable way. In this study, the influence of MF on surface integrity of Ti-6Al-4V (TC4) is firstly reported. Experimental results show that MF treatment reduces surface roughness (R_a) and increases micro-hardness by 48% and 11.8% at most, respectively. Besides, a compressive stress layer with an amplitude of −1000 MPa and a depth of 0.8 mm is observed. This study analyzes the performance and reveals the potential of micro-forging technology, which lays a solid foundation for expanding its application in TC4 surface modification.     

固溶时效处理对高强高韧钛合金显微组织与力学性能的影响

对固溶时效处理后的高强高韧钛合金初生α相的体积分数、尺寸,次生α相的体积分数和α_s/β相界面密度等显微组织特征进行了定量表征和统计分析,探讨了随着固溶温度的变化,高强高韧钛合金显微组织与其力学性能间的相关性.结果表明:在α+β两相区固溶时效处理,随着固溶温度的升高,合金初生α相的体积分数降低,相尺寸先降低后略有升高,次生α相的体积分数升高,α_s/β相界面密度先升高后降低.初生α相的体积分数与伸长率、静力韧度和裂纹形成功正相关,α_s/β相界面密度与合金屈服强度成正相关.      

基于Deform软件二次开发和BP神经网络的TA15多向锻造微观组织预报

通过热压缩实验构建了TA15合金的热变形真应力-应变曲线,以此为基础分别建立了合金双相区及单相区温度区间的热变形本构方程;基于热压缩试样动态再结晶的统计数据建立了TA15合金的动态再结晶模型。借助Deform提供的二次开发功能实现相关数学模型的程序化,制定正交实验方案,实现了TA15合金多向锻造变形的微观组织仿真。通过正交实验分析得出各项因子的影响对象及强弱差异,提出了双相区及单相区温度区间内的多向锻造最佳因子组合。建立了TA15合金多向锻造变形微观组织的BP （Back Propagation）神经网络预测模型,将预测结果与有限元仿真结果进行比较,结果表明两种方法的预测结果基本一致,但神经网络具备有限元仿真难以实现的良好细节预测能力,能更为细致地实现对微观组织分布状态的划分。     

Precipitation behavior and properties of extruded 7136 aluminum alloy under different aging treatments

In this work, the mechanical properties and electrical conductivity of the extruded 7136 aluminum alloy treated by single-stage aging treatment (T6), retrogression and re-aging treatment (RRA), and multiple retrogression and re-aging treatment have been investigated by means of hardness measurements, electrical conductivity tests and tensile tests. The results have shown that the properties of the 7136 alloy such as hardness, tensile strength and electrical conductivity were sensitive to retrogression time (within 90 min). With prolonging the retrogression time, the tensile strength was enhanced first and then decreased, yet the electrical conductivity was continuously increased. The 60 min-treated alloy performed the highest tensile strength (716 MPa), whereas the 90 min-treated alloy possessed the highest electrical conductivity (33.95%IACS). Compared with the T6-treated alloy, the tensile strength and electrical conductivity were improved by 3.3% and 18.9%, respectively. The electrical conductivity showed an obvious increase with repetitious times of the RRA treatment. After 3RRA60 treatment, a good combination of tensile strength (705 MPa) and electrical conductivity (33.20%IACS) can be obtained. Compared with the T6 condition, the tensile strength and electrical conductivity were improved by 1.7% and 16.3%, respectively. The mechanism of microstructure evolution under different aging treatments has been discussed in detail.     

含金属相变材料温控组件的研究

研究使用一种含有金属相变材料（Phase Change material,PCM）的温控组件（Thermal Control Component,TCC）对航天器上的有效载荷进行温度控制。通过对载荷的温控需求分析,设计并制备了以Ga-Sn合金为PCM的TCC,并通过地面模拟实验对TCC的温控性能进行测试。实验结果表明这种含有Ga-Sn合金的TCC满足载荷的温控需求。最后在仿真软件中建立了TCC的相变传热仿真模型用于预测TCC的温控性能。结果表明：仿真模型计算所得结果与实验结果基本一致,可用于预测TCC的温控性能。     

低合金钢管的焊接工艺及缺陷预防

采用氩弧焊打底,焊条电弧焊填充盖面焊接Cr5Mn低合金钢管,钢管壁厚为12mm,焊接位置为水平固定全位置焊接,在焊接之前,调整好焊接工艺参数,焊接完毕以后,对焊缝外观检验和X射线无损检测,发现焊缝的表面出现少量微裂纹,内部有少量气孔。为了保证焊缝的质量,对缺陷产生的原因进行分析并且采取正确的焊接工艺方法避免焊接缺陷。     

TC4-DT钛合金磨削表面特性及其摩擦磨损性能

钛合金是一种典型难磨削加工材料,磨削表面易出现烧伤、裂纹等热损伤。本文开展了TC4-DT钛合金磨削实验,通过扫描电镜（SEM）、能谱（EDS）、X射线衍射（XRD）、显微硬度仪、金相显微镜及球-盘摩擦磨损实验仪研究了其表面特性及摩擦磨损性能。结果表明：低速磨削表面质量好,摩擦磨损性能较基体略提高;当砂轮线速度为80 m/s时,磨削表面质量良好,摩擦系数为0.38,较基体降低40%;而砂轮线速度为100 m/s时,磨削表面出现严重烧伤、网状裂纹。因此选择合理的高速磨削工艺可避免烧伤、裂纹等热损伤缺陷,并可有效改善表面摩擦磨损性能;磨削表面干摩擦磨损机制为磨粒磨损、粘着磨损和剥层磨损。     

不同温度和应变速率下BTi6431S新型钛合金流变应力行为

通过在870～900°C温度范围内和应变速率为0.000 1～0.01/s下,对BTi6431S新型钛合金薄板进行了单向拉伸试验,研究了BTi6431S新型钛合金在高温条件下流动应力与变形温度和应变速率之间的关系,并利用改进的Hooke law和Grosman方程建立了BTi6431S钛合金的应力-应变本构模型。研究结果表明:BTi6431S钛合金在870～900°C温度下,流动应力随着温度的升高而降低,随着应变速率的增大而明显升高,在进入塑性变形区间,基本保持稳态流动。拟合得到的本构方程能够较准确地反映了BTi6431S钛合金在高温下的流动应力变化情况。     

BTi6431S钛合金盒形件热拉深成形工艺数值模拟

为研究BTi6431S钛合金热拉深成形工艺,本文以某型号飞行器天线盒盖为例,通过设计正交实验方案,先后分别对无压边情况下拉深成形进行了有限元数值模拟,用最薄壁厚减薄率作为描述零件成形结果的评价标准,得出该钛合金件在成形温度为650°C,首次拉深凹模圆角半径11mm、凸模圆角半径7mm、转角半径12mm、拉深高度25mm参数下,最薄壁厚减薄率最小(20.3%)。     

采用SMA驱动的小型空间磁悬浮飞轮锁紧机构

磁悬浮飞轮锁紧机构在卫星发射时锁紧飞轮,减小其振动和冲击载荷;在发射后解锁,保证飞轮正常工作.目前已有的以火工品或步进电机驱动的锁紧机构具有冲击大、体积较大、不可重复使用等缺点.提出了一种采用形状记忆合金(SMA, Shape Memory Alloy)驱动的空间磁悬浮飞轮锁紧机构的设计方案,并在Liang本构模型的基础上发展了机构驱动单元的设计方法.之后,完成了锁紧机构的样机研制和调试,并开展了地面的性能测试、振动试验和高温环境试验.研究结果表明:SMA锁紧机构安装体积小,在星载28 V电压下能在6 s内完全锁紧,在1 s内完全解锁,并能够通过振动和环境实验.SMA驱动的磁悬浮飞轮锁紧机构具有锁紧力大、同步性好、可重复使用、低冲击、无污染等优势,有很大的工程应用潜力.