全文获取类型
收费全文 | 1456篇 |
免费 | 321篇 |
国内免费 | 211篇 |
专业分类
航空 | 1362篇 |
航天技术 | 100篇 |
综合类 | 239篇 |
航天 | 287篇 |
出版年
2024年 | 17篇 |
2023年 | 42篇 |
2022年 | 58篇 |
2021年 | 57篇 |
2020年 | 59篇 |
2019年 | 61篇 |
2018年 | 44篇 |
2017年 | 46篇 |
2016年 | 52篇 |
2015年 | 59篇 |
2014年 | 63篇 |
2013年 | 68篇 |
2012年 | 88篇 |
2011年 | 69篇 |
2010年 | 77篇 |
2009年 | 96篇 |
2008年 | 100篇 |
2007年 | 80篇 |
2006年 | 65篇 |
2005年 | 82篇 |
2004年 | 58篇 |
2003年 | 57篇 |
2002年 | 70篇 |
2001年 | 53篇 |
2000年 | 44篇 |
1999年 | 29篇 |
1998年 | 41篇 |
1997年 | 31篇 |
1996年 | 58篇 |
1995年 | 31篇 |
1994年 | 50篇 |
1993年 | 35篇 |
1992年 | 49篇 |
1991年 | 34篇 |
1990年 | 15篇 |
1989年 | 23篇 |
1988年 | 11篇 |
1987年 | 9篇 |
1986年 | 3篇 |
1985年 | 2篇 |
1983年 | 1篇 |
1981年 | 1篇 |
排序方式: 共有1988条查询结果,搜索用时 15 毫秒
141.
余瑞莲%汪明%李弘瑜%杨云华%冯志海 《宇航材料工艺》2008,38(2):6-8
以苯乙炔封端聚酰亚胺树脂为基体,采用高温R1M工艺复合成型了T300碳布增强聚酰亚胺层合板,复合材料的Tg达351℃(DMA),材料在300℃弯曲强度保持率达90%以上,模量保持率达85%以上,层间剪切强度保持率达60%以上. 相似文献
142.
郭建%魏伯荣%刘生辉 《宇航材料工艺》2008,38(2):43-45
研究了NBR/EPDM并用胶的硫化体系中各组份对并用胶性能的影响.结果表明:DCP对并用胶的性能影响最大,TMPTMA对于并用胶的影响主要是通过与DCP的协同作用来体现的,TAIC对于并用胶的影响主要在撕裂强度方面,增加或减少TAIC的用量均对撕裂强度的提高有利. 相似文献
143.
采用RFI工艺分别成型了648和5228A环氧树脂基复合材料层合板,其增强材料为碳纤维无屈曲织物,铺层方式为[(0,90)/( 45)]s;测试了两组层舍板的拉伸性能、弯曲性能和层间剪切性能并做了比较分析;对破坏形式和机理进行了探讨.结果表明:5228A相对于648环氧树脂膜有较宽的低黏度区域,较长的凝胶时间;5228A与648层合板相比,拉伸强度高106%,拉伸模量、泊松比接近;弯曲强度高58%,弯曲模量高16%;层间剪切强度高62%. 相似文献
144.
基于静强度分布的复合材料疲劳寿命分布的预测模型(英文) 总被引:2,自引:2,他引:2
The reasons of the static strength dispersion and the fatigue life dispersion of composite laminates are analyzed in this article. It is concluded that the inner original defects, which derived from the manufacturing process of composite laminates, are the common and major reason of causing the random distributions of the static strength and the fatigue life. And there is a correlative relation between the two distributions. With the study of statistical relationship between the fatigue loading and the fatigue life in the uniform confidence level and the same survival rate S-N curves of material, the relationship between the static strength distribution and the fatigue life distribution through a material S-N curve model has been obtained. And then the model which is used to describe the distributions of fatigue life of composites, based on their distributions of static strength, is set up. This model reasonably reflects the effects of the inner original defects on the static strength dispersion and on the fatigue life dispersion of composite laminates. The experimental data of three kinds of composite laminates are employed to verify this model, and the results show that this model can predict the random distributions of fatigue life for composites under any fatigue loads fairly well. 相似文献
145.
对航空发动机技术水平提高速度与投资强度这两个概念做了界定.利用有关数据,针对航空涡轮发动机的技术水平提高速度、最大推力、类型(涡喷或涡扇)与投资强度的定量关系建立了的一个数学模型,并对模型的应用进行了探讨. 相似文献
146.
147.
148.
《燃气涡轮试验与研究》2007,20(2):F0002-F0002
陆山,西北工业大学动力与能源学院教授、博士生导师,航空学会动力分会可靠性专业委员会委员,航空学会失效分析分会委员,曾任美国依阿华州立大学航空工程及工程力学系博士后副研究员。从事航空发动机结构强度分析工作20余年,先后主持或参加了航空部高推预研、发动机结构完整性、航空基金、国防科工委项目课题等20多项。发表学术论文45篇,被SCI、EI、LNSPEC索引19篇次,获省部级科技奖2项。 相似文献
149.
采用折光指数控制法研究了改性氰酸酯树脂体系的预聚效果.结果表明:当折光指数在 1.574 5~1.578 5 时,改性氰酸酯树脂的软化点可控制在 25~30℃,室温铺覆性能良好.力学性能及耐环境性研究表明 M40/BADCy 复合材料的层间剪切强度可达到67.8 MPa.高低温交替变化及紫外线老化对 M40/BADCy 复合材料的力学性影响很小.M40/BADCy 复合材料水煮 100 h 后的吸水率小于0.94%,其层间剪切强度仅下降18%. 相似文献
150.
尹志民%肖静%雷学锋%何振波%聂波 《宇航材料工艺》2008,38(1):51-55
采用铸锭冶金法制备了 Al-6.0Zn-2.0Mg-0.12Zr 和 Al- 6.0Zn - 2.0Mg - 0.2Sc - 0.12Zr 两种合金板材,以 Al-Mg-Sc-Zr焊丝为焊接填充材料,对3 mm厚的上述两种合金板材进行氩弧焊接,之后对两种接头的显微组织和力学性能进行对比研究.结果表明:第一,微量Sc可以显著提高Al-Zn-Mg-Zr合金基材的拉伸性能,基材强度的提高来源于晶粒细化强化、Al3(Sc,Zr)粒子的析出强化和Al3(Sc,Zr)粒子引起的亚结构强化;第二,焊接过程中,不含 Sc 的合金焊接接头热影响区内η相(MgZn2)粒子和晶粒明显粗化,含 Sc的合金焊接接头热影响区内η相(MsZn2)粒子也明显粗化,但晶粒大小没有明显变化,由于Al3(Sc、Zr)粒子稳定性高,不容易粗化和团聚,对位错和亚晶界仍然起钉扎作用,热影响区仍然保持未再结晶组织,过时效软化现象相对于传统的铝镁合金来说不是很严重;第三,微量 Sc 可以明显提高 Al-Zn-Mg-Zr 合金焊接接头的强度,与不加 Sc 的合金焊接接头相比,添加Sc的合金拉伸强度从395 MPa提高到447 MPa,强度系数从 0.7 提高到0.8.强度的提高主要来源于晶粒细化强化、Al3(Sc,Zr)粒子的析出强化和由于Al3(Sc,Zr)粒子的高稳定性导致的的抗热循环软化能力的提高. 相似文献