正十七烷与正十八烷对航空煤油理化性能及液滴平均直径的影响

讨论了正十七烷与正十八烷(C₁₇,C₁₈)对燃料运动黏度、密度、表面张力理化性能的影响,探究了直链烷烃对SMD(Sauter mean diameter)的影响.将Key's混合规律、Tat混合规律和多项式拟合应用于密度公式的拟合,并将Key's混合规律与对数拟合应用于运动黏度公式的拟合,得出的理化性能拟合公式精度较高;通过测量纯煤油及C₁₇,C₁₈混合油雾化的SMD,实验发现随着直链烷烃的质量分数的增加,混合油的运动黏度增加,SMD也随之增加,雾化效果与纯航空煤油的相比较差,而C₁₈混合油的SMD要比C₁₇混合油要大,并且利用密度、运动黏度的拟合公式对SMD进行预测的偏差小于0.3%.      

基于CST方法的高空低雷诺数吸附式叶型耦合优化设计

研究了一种基于类别形状函数变换（CST）方法的吸附式叶型优化设计方法,该方法可以在高空低雷诺数条件下对叶型和抽吸方案耦合优化.结果表明:优化之后在20km高空低雷诺数条件下总压损失降低了65%,静压升提高了0.02,气动性能得到较大提升.而且由于优化过程中罚函数的引入使得优化后吸附式叶型在地面条件下性能也有所提高.对于高空低雷诺数条件下吸附式叶型在抽吸位置之前适当的增加叶型负荷,再通过抽吸来控制附面层,效果最优.并且最佳抽吸位置位于层流分离泡作用区域内.在层流分离泡作用区域内抽吸可以完全消除层流分离泡对叶型性能的影响,并且可以较好控制附面层位移厚度和动量厚度的增加,有效地减小附面层内的动量损失.      

基于改进粒子群算法的串列叶型优化设计

为了提高串列叶型优化设计的质量,设计了一套基于改进粒子群算法的串列叶型自动优化系统。研究了原始粒子群算法,提出了一种粒子群算法的改进方法。结果发现,改进粒子群算法的收敛速度和收敛精度明显优于原始粒子群算法和遗传算法。以50°大弯角串列叶型为研究对象,使用程序对串列叶型参数化。以叶型参数和串列叶型相对位置的参数作为优化变量,结合BP神经网络和改进粒子群算法对串列叶型进行优化设计。优化结果表明,优化后的叶型在设计攻角时的总压损失系数降低了22%,静压比升高了0.6%,在负攻角时,优化后的叶型的流动性能得到了明显改善。适当减小串列叶型前后缘的半径可以减小叶型的损失,合理的缝隙结构可以有效减小前排叶型压力面和后排叶型吸力面附面层的分离损失。     

基于代理模型的二元收扩喷管流道型面优化设计

在二元收扩（2D-CD）喷管设计参数对喷管气动性能影响研究的基础上,以获得尽可能高的喷管推力系数为目标,以喉道宽高比、喉道型面半径比、收敛半角和扩张半角为设计变量,对二元收扩喷管的流道型面进行了优化设计。设计过程中,利用正交试验设计方法确定初始样本点,建立喷管推力系数与设计参数间的Kriging代理模型,采用自适应模拟退火算法（ASA）对代理模型进行分析求解。结果表明,二元收扩喷管的优化型面参数为:喉道宽高比为6,喉道型面半径比为0.3,收敛半角为15°,扩张半角为5.64°,此时最大推力系数为0.97847,流量系数为0.98778.      

金属丝网橡胶的本构关系

通过对圆环形金属丝网橡胶成型制造过程的分析,在圆环嵌套模型基础上,结合干摩擦非线性理论和小曲梁模型建立了金属丝网橡胶材料的非线性本构关系,对不同相对密度的金属丝网橡胶试件进行了静态压缩实验,通过实验数据确定了本构关系方程的各项系数并实验结果进行比较.研究结果表明:建立的本构关系模型可以很好地描述金属丝网橡胶的非线性力学特性,实验结果能够较好地符合理论结果,并且该模型反映了相对密度、网格大小和网格宽度等参数的影响,从而实现了对材料结构刚度的预估.      

机场容量利用及流量分配优化策略

为了充分利用机场容量,减少航班延误,需要合理分配进离场流量。以机场容量作为约束,以进离场航班总延误成本最小作为目标,建立进离场流量分配优化模型。构建随延误时间呈超线性增长的延误成本计算公式,引入航班进离场延误成本权重系数作为不同进离场优先级的决策偏好信息。用动态规划法求解模型,并引入最优决策候选集合的概念,缩小计算过程中的搜索量,减少计算时间。算例结果分析表明,方法可以在机场容量约束下得出进离场流量分配的最优策略,使得航班总延误成本最小,并且快速计算可以满足实时决策支持的要求。     

可重构零空间控制分配算法及流程规划

针对飞机正常情况和舵面故障情况下的控制分配算法展开研究。根据控制效能矩阵的特点设计了性能指标,并给出了对应的最优逆控制。对带约束的一般控制分配问题,采用零空间横截方法进行了再分配。设计了针对舵面卡死故障的重构控制律。结合某飞机仿真平台,进行了卡死故障的重构仿真,结果表明,控制分配算法能够在故障状态下完成对指令的精确跟踪。     

一种减少失速保护虚警率的混合滤波方法

针对飞机失速保护设计过程中易出现虚警的情况,提出一种基于FIR和传统滤波器相结合的混合滤波方法。结合飞机本体的运动特征,对参与失速保护逻辑运算的两个重要参数,即侧向加速度和迎角信号进行频率分析,基于信号的特征设计混合滤波器,然后采用Simulink滤波工具箱设计滤波器对信号进行滤波处理。仿真结果表明该方法能够减少虚警率的发生,特别是大背景噪声下的虚警率能够得到较好抑制,验证了滤波器设计正确性,从而提高失速保护功能对适航条款符合性。该滤波器设计方法,不但可以有效解决本文提到的问题,对于其他涉及信号处理的系统设计同样具有借鉴意义。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.