存在观测站位置误差的转发式时差无源定位

无源定位中,由于观测站安放在运动平台等原因造成的观测站位置误差会影响无源定位精度性能。另外到达时间差(简称时差)(TDOA)的转发式测量需要将不同观测站截获到的辐射源信号都转发到同一位置,如主观测站。针对这两个问题,提出了基于约束总体最小二乘(CTLS)的无源定位算法。首先将转发式时差的非线性定位方程转化为不需要中间变量的直接线性方程,再基于CTLS算法依次转化为约束优化问题和无约束优化问题,最后推导给出定位近似闭式解。仿真实验表明在观测站误差较大时,该算法与其他算法相比定位精度性能较好。     

Gust response analysis and wind tunnel test for a high-aspect ratio wing

A theoretical nonlinear aeroelastic response analysis for a flexible high-aspect ratio wing excited by harmonic gust load is presented along with a companion wind tunnel test. A multidisci-plinary coupled numerical calculation is developed to simulate the flexible model wing undergoing gust load in the time domain via discrete nonlinear finite element structural dynamic analysis and nonplanar unsteady vortex lattice aerodynamic computation. A dynamic perturbation analysis about a nonlinear static equilibrium is also used to determine the small perturbation flutter bound-ary. A novel noncontact 3-D camera measurement analysis system is firstly used in the wind tunnel test to obtain the spatial large deformation and responses. The responses of the flexible wing under different static equilibrium states and frequency gust loads are discussed. The fair to good quanti-tative agreements between the theoretical and experimental results demonstrate that the presented analysis method is an acceptable way to predict the geometrically nonlinear gust response for flex-ible wings.     

正十七烷与正十八烷对航空煤油理化性能及液滴平均直径的影响

讨论了正十七烷与正十八烷(C₁₇,C₁₈)对燃料运动黏度、密度、表面张力理化性能的影响,探究了直链烷烃对SMD(Sauter mean diameter)的影响.将Key's混合规律、Tat混合规律和多项式拟合应用于密度公式的拟合,并将Key's混合规律与对数拟合应用于运动黏度公式的拟合,得出的理化性能拟合公式精度较高;通过测量纯煤油及C₁₇,C₁₈混合油雾化的SMD,实验发现随着直链烷烃的质量分数的增加,混合油的运动黏度增加,SMD也随之增加,雾化效果与纯航空煤油的相比较差,而C₁₈混合油的SMD要比C₁₇混合油要大,并且利用密度、运动黏度的拟合公式对SMD进行预测的偏差小于0.3%.      

基于FPGA的DDR2缓存控制器在 无线链路图像跟踪系统中的应用

图像跟踪系统是机载光电吊舱的重要组成部分,其对目标捕捉的成功率直接决定了机载光电吊舱的性能.而作用于机载光电吊舱与地面站之间的无线链路系统,有着不可消除的的延时特性,这极大地降低了目标捕捉成功率.本文设计了一种基于FPGA的DDR2缓存控制器,通过缓存控制器可以轻松实现高清视频图像的快速存储和调用,从而实现图像跟踪算法对无线链路延时的补偿.该缓存控制器成功应用于某型机载光电吊舱图像跟踪系统,有效消除了无线链路延时的影响,提高了图像跟踪系统对目标捕捉的成功率.     

固体火箭发动机CT图像条状伪影校正

为了校正窄角扇束工业CT扫描重建的固体火箭发动机图像中的条状伪影,分析了条状伪影的产生原因.针对条状伪影是由重排和数据对齐后固体火箭发动机投影数据的非光滑连续性引起的,提出了条状伪影校正的两种算法.两种算法均以中间平移步数的投影数据为基准进行投影数据的重排,一种将重排和数据对齐过程分开处理;另一种将重排和数据对齐过程合并处理.为了验证两种条状伪影校正算法的有效性,采用窄角扇束工业CT对某型固体火箭发动机进行3种不同扫描步长的扫描和重建.结果表明重排和数据对齐过程分开处理的校正算法只有在小步长扫描的情况下重建效果较好,条状伪影较少;而重排和数据对齐过程合并处理的校正算法在3种不同的扫描步长下图像重建质量均较好,条状伪影较少.      

基于定位特征点的叶片锥束CT点云模型配准方法

针对实际生产过程中锥束CT检测空心涡轮叶片的点云数据与计算机辅助设计模型的配准问题,提出了一种基于定位特征点的叶片锥束CT点云模型配准方法。首先将点云数据与计算机辅助设计模型进行预配准;然后查找空心涡轮叶片的设计定位特征点坐标;最后根据定位基准点寻找点云数据上与之对应的基准点,并建立各自坐标系,根据坐标系进行几何变换,迭代直至满足要求,从而完成精确配准。试验结果表明,该方法很好地实现了锥束CT点云模型的配准定位,满足了实际生产要求。     

一种减少失速保护虚警率的混合滤波方法

针对飞机失速保护设计过程中易出现虚警的情况,提出一种基于FIR和传统滤波器相结合的混合滤波方法。结合飞机本体的运动特征,对参与失速保护逻辑运算的两个重要参数,即侧向加速度和迎角信号进行频率分析,基于信号的特征设计混合滤波器,然后采用Simulink滤波工具箱设计滤波器对信号进行滤波处理。仿真结果表明该方法能够减少虚警率的发生,特别是大背景噪声下的虚警率能够得到较好抑制,验证了滤波器设计正确性,从而提高失速保护功能对适航条款符合性。该滤波器设计方法,不但可以有效解决本文提到的问题,对于其他涉及信号处理的系统设计同样具有借鉴意义。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

S形进气道锤击波荷载特性分析

利用基于改进的延迟分离涡模拟（IDDES）方法,对亚声速和超声速来流条件下某S形模型进气道进行了非定常计算,研究了发动机喘振所产生的瞬时高压波形对锤击波传播规律的影响.结果表明:锤击波产生后沿进气道迅速向前传播,运动过程中锤击波的运动速度基本保持不变,但强度不断增强.同时受气流离心力的影响,S形进气道弯曲段半径较大一侧壁面受到的锤击波气动荷载值更大.发动机喘振所产生的瞬时高压的加载梯度增加使得锤击波传播速度及强度增强,而压力卸载方式对锤击波强度的影响不明显.在亚声速和超声速来流条件下,增加瞬时高压峰值均使得锤击波荷载强度显著增强,并近似符合二次函数分布规律,而且超声速来流条件下锤击波强度较亚声速来流更强.