建造中的我国低速增压风洞

本文论述了在我国建造低速增压风洞的重要性和必要性，同时还介绍了国外低速高雷诺数风洞的发展现状，并提出了衡量现代生产性风洞性能的标准，给出了正在建造的我国低速增压风洞的主要技术性能及设计和建造中的关键技术。     

模型旋翼与全尺寸旋翼风洞试验结果的比较

本文介绍了旋翼原理样机4m模型旋翼在CARDC 8m×6m闭口风洞的试验结果与全尺寸旋翼在俄罗斯TSAGI T101开口风洞试验结果的比较.     

可调桨距冲压空气涡轮气动特性实验与数值分析

冲压空气涡轮风洞实验主要目的是采用相似准则,模拟空中加油工作状态,测量涡轮输出功率,分析涡轮气动特性。实验分别使用励磁发电机和加油泵作为测功器,通过调桨变距并测量最大输出功率。气动特性实验表明在风洞气流速度比加油机最小飞行速度低16%的条件下,冲压涡轮输出功率即可满足加油需要。论文还采用高数值稳定性代数Baldwin-Lomax湍流模型模拟冲压涡轮全三维混合型流场,分析流场主要气动特性,讨论桨叶表面载荷的分布。数值模拟结果显示在冲压空气涡轮桨叶近轮毂区域需要进一步优化。      

后掠翼对细长体头部侧向力特性的影响

通过在细长体顶点处设置扰动块的方式使细长体的绕流具有确定性,在此基础上研究了机翼对细长体头部侧向力特性的影响.通过实验发现,测压截面越靠近机翼顶点,受机翼的影响越大.在50°迎角以下,后掠翼对细长体头部侧向力特性的影响很小.在60°迎角时,后掠翼对细长体头部的侧向力特性影响较大,此时单独细长体的侧向力特性实验结果已不能直接应用于后掠翼身组合体了.     

用胞映射法分析双线性结构刚度的机翼颤振

将映射轨迹追踪技术引入基于空间Poincar啨截面的胞映射方法中 ,并定义初值分析空间 ,以适应分析高维动力系统运动类型初值域的需要。改进后胞空间中胞的数目大大减少 ,计算时间缩短 ,运动特征的确认更为准确。应用该方法研究扭转方向具有双线性结构刚度因素的机翼颤振问题 ,结果显示 ,初始条件对系统动力学行为有着很大的影响。当两段刚度之比小于某临界值时 ,随着机翼颤振速度增大 ,不同的初始条件会导致平衡点、极限环振动、复杂的周期运动、混沌和发散运动等不同的运动形式     

多变量非线性非定常气动力的模糊逻辑模型

应用模糊逻辑算法，建立了带升降舵偏角影响的非线性非定常气动力模型逻辑模型，并进行了验证，结果表明：所建立的非定常气动力模型逻辑模型有较强的预测能力，此方法为今后建立多变量、复杂运动的非线性非定常气动力学数学模型，提供很好的借鉴。     

边界层流动的非平行稳定性研究

采用极为有效的抛物化稳定性方程（PSE）方法研究边界民支的非平行稳定性。并利用抛物线坐标变换、有限远延拓边界条件、及流向和法向全差分的数值方法，对不同频率的二维Tollmien-Schichting波的非平行稳定尾进行了计算和分析，计算结果与Orr-Sommerfeld方程（OES）的解以及谱配置方法的PSE结果作了详细的比较，得到了满意的结果。     

高速列车进入带缓冲结构隧道的压力变化研究（I）

给出了列车穿越带有缓冲结构的隧道压力变化的三维粘性流场数值模拟过程，控制方程为三维粘性、可压缩、非定常流的N．S方程，空间离散采用了中心有限体积法格式，时间采用预处理二阶精度多步后差分格式进行离散，对列车与隧道之间的相对运动采用移动网格技术处理。对不同的缓冲结构缓解隧道内瞬变压力及压力梯度的作用进行了研究。研究结果表明，缓冲结构的设置能够有效地降低隧道内的压力和压力梯度的最大值，其原因在于缓冲结构延长了压缩波压力上升的时间，降低列车突入隧道时所形成的最大压力梯度；另一方面由于压缩波在缓冲结构和列车、隧道之间多次的反射，也降低了压力峰值。     

Sliding mode control based guidance law with impact angle constraint

The terminal guidance problem for an unpowered lifting reentry vehicle against a sta- tionary target is considered. In addition to attacking the target with high accuracy, the vehicle is also expected to achieve a desired impact angle. In this paper, a sliding mode control （SMC）-based guidance law is developed to satisfy the terminal angle constraint. Firstly, a specific sliding mode function is designed, and the terminal requirements can be achieved by enforcing both the sliding mode function and its derivative to zero at the end of the flight. Then, a backstepping approach is used to ensure the finite-time reaching phase of the sliding mode and the analytic expression of the control effort can be obtained. The trajectories generated by this method only depend on the initial and terminal conditions of the terminal phase and the instantaneous states of the vehicle. In order to test the performance of the proposed guidance law in practical application, numerical simulations are carried out by taking all the aerodynamic parameters into consideration. The effec- tiveness of the proposed guidance law is verified by the simulation results in various scenarios.     

Aeroelastic two-level optimization for preliminary design of wing structures considering robust constraints

An aeroelastic two-level optimization methodology for preliminary design of wing struc- tures is presented, in which the parameters for structural layout and sizes are taken as design vari- ables in the first-level optimization, and robust constraints in conjunction with conventional aeroelastic constraints are considered in the second-level optimization. A low-order panel method is used for aerodynamic analysis in the first-level optimization, and a high-order panel method is employed in the second-level optimization. It is concluded that the design of the abovementioned structural parameters of a wing can be improved using the present method with high efficiency. An improvement is seen in aeroelastic performance of the wing obtained with the present method when compared to the initial wing. Since these optimized structures are obtained after consideration of aerodynamic and structural uncertainties, they are well suited to encounter these uncertainties when they occur in reality.