利用多普勒原理测量微机电系统中微结构的动态特性

介绍了将显微扫描激光多普勒测振仪与基础激振法相结合的微结构动态特性的非接触无损测量方法、扫描激光多普勒测振仪的工作原理、设计的基础激振器及其驱动信号.并给出典型微结构--微悬臂梁的测量结果.测量结果与理论计算及有限元仿真结果相符,验证了该方法的有效性.     

低功率激光-TIG电弧复合焊接不锈钢熔深研究

建立了一套低功率YAG脉冲激光-TIG电弧复合热源焊接系统,并用本系统对不锈钢1Cr18Ni9Ti进行焊接.研究了3种热源作用下不锈钢的焊缝熔深.通过引入焊缝有效热输入概念,对复合热源影响熔深的机理进行了分析.     

孔间距和前倾角对进出口扩张形气膜孔流量系数的影响(英文)

Discharge coefficients of 3-in-1 hole of three inclination angles and three spacing between holes are presented which described the discharge behavior of a row of holes. The inlet and outlet of the 3-in-1 hole both have a 15° lateral expansion. The flow conditions considered are mainstream turbulence intensities and density ratios of secondary flow to mainstream. The momentum flux ratios varied in the range from 1 to 4. The comparison is made of the discharge coefficients of three shaped holes to find an optimal hole with low flow loss. The results show that the discharge coefficients of 3-in- 1 hole are highest in three shaped holes and therefore this article is focused on the measurements of discharge coefficients of 3-in-1 hole for various geometries and aerodynamic parameters. The measured results of 3-in-1 hole indicate that turbulence intensities, density ratios and momentum flux ratios have weak influence on discharge coefficients for inclination angle of 20°. The high turbulence intensity yields the small discharge coefficients for inclination angle of 45° and 90°. The increased both momentum flux ratios and density ratios lead to the increased discharge coefficients for inclination angle of 45° and 90°. The increased inclination angle causes the rapidly increased discharge coefficients. There is a weak dependence of discharge coefficients on hole pitches.     

Foreign Object Damage to Fan Rotor Blades of Aeroengine Part Ⅱ： Numerical Simulation of Bird Impact

Bird impact is one of the most dangerous threats to flight safety. The consequences of bird impact can be severe and, therefore, the aircraft components have to be certified for a proven level of bird impact resistance before being put into service. The fan rotor blades of aeroengine are the components being easily impacted by birds. It is necessary to ensure that the fan rotor blades should have adequate resistance against the bird impact, to reduce the flying accidents caused by bird impacts. Using the contacting-impacting algorithm, the numerical simulation is carded out to simulate bird impact. A three-blade computational model is set up for the fan rotor blade having shrouds. The transient response curves of the points corresponding to measured points in experiments, displacements and equivalent stresses on the blades are obtained during the simulation. From the comparison of the transient response curves obtained from numerical simulation with that obtained from experiments, it can be found that the variations in measured points and the corresponding points of simulation are basically the same. The deforming process, the maximum displacements and the maximum equivalent stresses on blades are analyzed. The numerical simulation verifies and complements the experiment results.     

AZ31B变形镁合金激光-MIG复合焊焊接组织和性能分析

采用激光-MIC复合焊对10mm厚的AZ31B变形镁合金进行焊接.利用光学显微镜、扫描电镜、X射线衍射仪等手段分析了焊接接头的外观和截面特征、显微组织、元素分布、焊缝物相和断口形貌等,并检测了接头区域硬度和接头强度.试验结果表明:采用激光-MIG复合焊能获得成形美观的焊缝,无明显的缺陷;焊缝热影响最大宽度位于激光区,约为100μm,焊缝组织为15～25μm的等轴晶粒;相比于母材,焊缝区的镁元素出现烧损,铝和锰元素的比例有一定增加;焊缝区主要为Mg,Al和少量的MgO相.焊接接头硬度值较均匀;焊缝抗拉强度达到222MPa,断口形貌为混合断裂断口.     

激光陀螺中光路调节系统的研究

本文针对陀螺掉光问题,分析了光路准直性变化（光路歪扭）带来的损耗对陀螺输出光强的影响,确定了光路歪扭调节角度的范围,设计了光路调节系统,并对其进行测试。结果表明,该系统在额定工作电压下,对光路歪扭角度的调节范围在-8″和+3″之间,具备光路调节的能力,可用于提高光路准直性。     

N5B飞机机身钢构架焊接架数字化设计与制造技术

详细阐述了在N5B飞机机身钢构架焊接架的设计与制造中运用数字化技术的先进性。     

TC4钛合金激光焊缝超塑性行为研究

研究了TC4钛合金板激光焊缝的超塑性变形行为、组织演变,以及激光焊接板的横向超塑性变形特征.引进等轴化系数表征超塑性变形过程中焊缝组织等轴化进程,并对激光焊接/超塑成型技术基础问题提出了进一步展望.     

变攻角下孔隙射流对高负荷扩压叶栅气动性能的影响

本文对采用孔隙射流的某大折转角雎气机叶栅进行了实验研究．给出了不同攻角下叶栅流道内的静压分布、表面极限流线以及出口流场的气动参数,通过在不同叶高处开孔探讨了孔隙射流位置对大负荷扩压叶栅气动性能的影响。实验结果表明,孔隙位置对端壁静压的影响不大;开多孔方案对叶栅气动性能的影响要强于单孔方案：在设计攻角下,孔隙射流能够改善角区流动,同时降低叶片中部损失,单孔方案的最佳开孔位置位于25％相对叶高处,质量平均能量损失系数相对原形叶栅降低4．75％,开多孔方案巾能量损失相对原形叶栅最多降低5．52％：在负攻角下．孔隙射流导致叶栅性能下降,而在正攻角下,孔隙射流大幅提高叶栅性能,能量损失系数相对原形叶栅最多降低12．7％。     

管中激光加速器的推力形成过程

管中激光加速器是一种新型的激光推力器,弹射体在管道中被加速。利用光线追踪法,根据光线在网格中的传播路径信息,运用辐射输运方程,得到流场的能量源项;数值求解含能量源项的流体控制方程,对管道中等离子体流场激波的形成和演化过程进行了研究。模型能够模拟空气光学击穿、空气对激光能量的吸收、等离子体对激光的屏蔽作用和推力形成过程,通过计算得到冲量耦合系数为3.61×10-4N/MW,等离子体内能转化为流场动能的比例约为9%。