全文获取类型
收费全文 | 1944篇 |
免费 | 670篇 |
国内免费 | 109篇 |
专业分类
航空 | 2375篇 |
航天技术 | 82篇 |
综合类 | 98篇 |
航天 | 168篇 |
出版年
2024年 | 18篇 |
2023年 | 68篇 |
2022年 | 109篇 |
2021年 | 100篇 |
2020年 | 84篇 |
2019年 | 97篇 |
2018年 | 64篇 |
2017年 | 74篇 |
2016年 | 95篇 |
2015年 | 86篇 |
2014年 | 122篇 |
2013年 | 143篇 |
2012年 | 143篇 |
2011年 | 118篇 |
2010年 | 108篇 |
2009年 | 118篇 |
2008年 | 109篇 |
2007年 | 90篇 |
2006年 | 87篇 |
2005年 | 84篇 |
2004年 | 87篇 |
2003年 | 82篇 |
2002年 | 67篇 |
2001年 | 54篇 |
2000年 | 59篇 |
1999年 | 45篇 |
1998年 | 44篇 |
1997年 | 56篇 |
1996年 | 49篇 |
1995年 | 55篇 |
1994年 | 43篇 |
1993年 | 29篇 |
1992年 | 21篇 |
1991年 | 19篇 |
1990年 | 27篇 |
1989年 | 43篇 |
1988年 | 8篇 |
1987年 | 8篇 |
1986年 | 5篇 |
1985年 | 2篇 |
1984年 | 1篇 |
1983年 | 1篇 |
1980年 | 1篇 |
排序方式: 共有2723条查询结果,搜索用时 31 毫秒
81.
为研究主流逆压力梯度下气膜孔的几何结构和气动参数对流量系数的影响规律,采用放大模型在低速回流式风洞中进行了实验。在对比研究圆柱孔和双向扩张孔流量系数基础上,重点研究了双向扩张孔的流量系数。结果表明,双向扩张孔的流量系数比圆柱孔的流量系数高。前倾角越大,流量系数越高;径向角越大,流量系数越高。流量系数随动量比的增加而增高,在动量比小于4时增幅尤其明显。主流湍流度增大使流量系数增大,动量比越小,增幅越大。除了在孔轴线与平板的夹角较大情况外,密度比对流量系数的影响较小。 相似文献
82.
针对叶片前缘结构的特点,建立了前缘气膜冷却实验台,实验模型由半圆柱面和两个平板组成,在距离滞止线2倍气膜孔直径距离位置布置了1排气膜孔。主流在前缘的湍流度为8%,二次流和主流密度比为1.5,动量比变化范围为0.5~4,分析了在不同动量比下气膜孔间距和径向角变化对径向平均气膜冷却效率的影响。径向角分别为0,°45,°65,°孔间距与孔径的比分别为2,3,4。研究结果表明,随着孔间距的增加,径向平均冷却效率逐渐降低。径向角对径向平均冷却效率的影响非常复杂。 相似文献
83.
84.
85.
86.
87.
88.
后掠大流量宽弦复合材料风扇叶片技术综述 总被引:1,自引:0,他引:1
用碳纤维复合材料制造的风扇叶片比钛合金夹芯结构的风扇叶片轻,在抗振特别是抗颤振性能方面也优于钛合金,抗鸟击能力和低噪声指标也获得适航当局的合格批准。装有高韧环氧复合材料风扇叶片的GE90发动机已装于波音777飞机,并在1995年投入航线运营使用。此项技术在十多年的使用时间里表现出色,无需例行的在役维护。 相似文献
89.
涡轮叶片粗糙度对其性能衰退的影响研究 总被引:5,自引:0,他引:5
涡轮是航空发动机核心部件之一,对整个发动机性能的发挥产生重大影响。导致航空发动机性能衰退的形式有很多种,其中由积垢沉淀因素造成的叶片粗糙度增大是具有代表性的原因。利用叶型基本数据进行两级涡轮建模,与传统建模方法相比,提高了模型精度。将所有导致涡轮性能衰退的因素都等价为叶片表面粗糙度的变化,并基于等价雷诺数修正原理,通过仿真方法定量研究了涡轮叶片由于积垢沉淀引起粗糙度增大从而导致其性能的衰退情况。仿真结果表明,当涡轮叶片表面粗糙度增大时,两级涡轮主要的特性参数都发生不同程度的减小,使涡轮总体性能下降。 相似文献
90.
Li Guangchao Zhu Huiren Fan Huiming Department of Aeroengines Northwestern Polytechnical University Xi’an China 《中国航空学报》2008,21(5):385-392
Discharge coefficients of 3-in-1 hole of three inclination angles and three spacing between holes are presented which described the discharge behavior of a row of holes. The inlet and outlet of the 3-in-1 hole both have a 15° lateral expansion. The flow conditions considered are mainstream turbulence intensities and density ratios of secondary flow to mainstream. The momentum flux ratios varied in the range from 1 to 4. The comparison is made of the discharge coefficients of three shaped holes to find an optimal hole with low flow loss. The results show that the discharge coefficients of 3-in- 1 hole are highest in three shaped holes and therefore this article is focused on the measurements of discharge coefficients of 3-in-1 hole for various geometries and aerodynamic parameters. The measured results of 3-in-1 hole indicate that turbulence intensities, density ratios and momentum flux ratios have weak influence on discharge coefficients for inclination angle of 20°. The high turbulence intensity yields the small discharge coefficients for inclination angle of 45° and 90°. The increased both momentum flux ratios and density ratios lead to the increased discharge coefficients for inclination angle of 45° and 90°. The increased inclination angle causes the rapidly increased discharge coefficients. There is a weak dependence of discharge coefficients on hole pitches. 相似文献