先进复合材料热塑性树脂浸渍技术进展

热塑性树脂应用存在两个难题:预浸料的制作和合适的复合材料成型工艺。浸渍工艺中混合纱浸渍法和 FIT 工艺有着广泛的应用前景。     

Storage life of silicone rubber sealing ring used in solid rocket motor

It is urgent to carry out detailed research on storage performance of rubber sealing ring to get the criterion for its storage life. This paper acquires material ageing regularity by theoretical analysis and experimental confirmation. On this condition, failure mode and failure criterion of typical sealing structure is studied, and the failure mechanism is found. Thus by analyzing the stress distribution, the relationship between ageing state and sealing condition is established. Rationalization proposal is put forward and storage life of sealing ring is evaluated. The research mentionedabove has special reference to the design of sealing structures and can provide reference for prolonging their service life.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

轴承、端面密封在液氧中的运转试验

利用高压液氧试验台,先后对新研制的用于液氧涡轮泵的轴承和端面密封进行了运转试验,验证了其在液氧环境中工作的安全性和可靠性。试验结果表明:新研制的端面密封和轴承能够在液氧中安全可靠的工作。特别是端面密封,即使在气氧环境中干摩擦,也能安全工作5分钟以上。试验还证明:在液氧环境中即使由于某种原因局部产生了小火花,只要能量不是足够大,其能量就会很快被液氧吸收,从而使温度降低,火花熄灭,不会产生燃烧爆炸的危险。     

高压小直径筒体密封结构分析设计

采用以弹性应力分析和塑性失效准则为基础的分析设计方法，对液体介质的高压小直径密封结构进行了理论分析及工艺试验，同时分析了影响密封效果的各种规范参数。经实际应用，证明该设计方法完全达到了设计要求。     

PIP工艺对2D高硅氧/甲基硅树脂复合材料结构与性能的影响

研究了不同浸渍工艺对2D高硅氧织物增强甲基硅树脂复合材料结构与性能的影响。结果表明,复合材料的密度及抗氧化性随着浸渍循环次数和热裂解温度的增加而增加;当热裂解温度不高于400℃时,复合材料仍具有较好的假塑性;但当热裂解温度高于400℃时,复合材料表现为典型的脆性断裂。当浸渍过程中热裂解温度为400℃、循环次数为2次时,500℃热处理20 m in的复合材料的室温弯曲强度最高,为49.8 MPa,比未处理的提高了150%。     

液体火箭发动机涡轮泵用机械密封温度场及热载变形研究

基于ANSYS数值计算软件,建立了液体火箭发动机涡轮泵用机械密封的二维稳态传热模型,依靠经验公式确定了模型的对流换热系数。计算了密封环的温度场和热载变形,分析了密封端面比压、回流流量以及不同材质对密封温度场的影响规律。结果表明:密封端面最高温度发生在靠近密封环内径处,且密封端面比压越大密封环温度梯度越大;密封环热载变形呈收敛间隙,最大变形发生在动环端面的外径处,其值约为2.2μm;密封环端面最高温度随回流流量增加而减小,当回流流量从0.1~0.6 kg/s变化时,密封环端面最高温度可降低18%(从100℃降至82℃);当回流流量增大到0.3 kg/s时,继续提高对密封环端面温升的控制不再显著;采用高导热系数的摩擦副材料能够显著降低端面温升和温度梯度,提高密封工作可靠性。     

一种新型深空探测样品封装技术

对样品进行真空封装是深空探测取样及返回任务中的一项核心技术,它能够成功维持样品成分原态。文章提出了一种能够符合我国深空探测任务的样品封装技术,其封装机构由复合式开合机构及火工锁紧机构组成,是一种极低漏率、高可靠的多层金属真空密封容器。通过对这种复合式开合机构和火工锁紧机构的特性方程的推导,对多层金属真空密封的材料匹配等机理的分析,确认这种新型的样品封装技术的原理是正确和可行的。最后对原理样机的性能进行了验证,结果表明:封装机构的体积小、功耗低、可靠性高,样机的密封性能良好,设计具有创新性及工程实用性。