复合材料层合结构低速冲击后的渗漏性能

对复合材料贮箱结构进行低速冲击试验,并测试冲击后贮箱结构的渗漏性能。试验结果表明,当层板内部的基体损伤和分层损伤构成贯穿的通路后即导致贮箱渗漏,并且贮箱结构的冲击能量渗漏门槛值介于23~25J之间。在试验基础上建立了有限元模型以分析冲击后贮箱结构的内部损伤情况,并判断结构是否渗漏,计算结果与试验吻合良好。在计算模型的基础上对曲面贮箱结构的冲击渗漏性能进行分析。     

2.5维机织复杂结构件的静强度

采用宏细观结合方法,针对经纱和纬纱等材料组分可能发生的多种失效模式,分别建立了基于改进的Hashin准则的系统性的材料失效准则及不同失效模式下的刚度退化模型.引入逐渐损伤的思想,建立了2.5维机织复杂结构件静强度系统性分析方法.模拟并分析了材料经向拉伸和纬向拉伸的应力-应变曲线,与实验得到的材料应力-应变曲线相比,相同应变下应力误差不超过6.5%,具有较好的重合度;对2.5维机织压气机静子连接结构模拟件开展了逐渐损伤模拟,结果表明:结构损伤主要集中在叶根倒角附近,其中吸力面叶根处的基体压缩失效形式会引起结构大幅变形,是结构破坏的主要原因.      

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

多重纳米结构轻质高强铝基复合材料的制备和组织性能

为了研究多重纳米结构对块体材料强化和变形能力的影响机制,采用粉末冶金法制备了多重纳米结构的B4C颗粒增强铝基复合材料,并对复合材料的强化和形变破坏机制进行了定量和定性的讨论。由100%球磨复合粉末制备的块体复合材料的室温压缩强度为670MPa;当加入10vol%气雾化态的Al2024粉末后,复合材料的室温压缩强度升高到1.115GPa;之后随着气雾化态Al2024粉末含量的增加,复合材料的强度逐渐下降,但是没有产生明显的塑性变形;当气雾化态Al2024粉末的含量增加到50vol%时,复合材料的压缩强度下降到580MPa,断裂前变形率达到了10%。扫描电镜(SEM)和透射电镜(TEM)的分析结果显示,亚微米级的B4C颗粒、位错以及纳米晶基体分别通过Orowan强化、位错强化和细晶强化机制对复合材料进行强化;粗晶Al2024区域与复合结构区域的比例显著影响复合材料的形变及破坏机制。     

面内弯曲载荷作用下两边简支两边固支复合材料层合板的屈曲

为扩充航空复合材料结构稳定性设计手段,基于Levy形式级数和有限差分法,提出了面内纯弯曲载荷作用下两边简支两边固支（SSCC）复合材料层合板临界屈曲载荷的数值解法。首先,应用有限差分法将挠度函数进行离散化处理;然后利用边界条件扩充方程组,最后将临界屈曲载荷的求解转化为广义特征值问题。通过数值算例分别在各向同性板和复合材料层合板上验证了本文方法,并与有限元方法（FEM）进行了比较。结果表明,本文方法具有很高的精度,为复合材料层合板的屈曲分析开辟了新的途径。     

压辊材料及形状对纤维铺放压紧效果的影响

近年来纤维铺放（AFP）技术被广泛用于大型复杂飞机复合材料构件成型。为了保证纤维铺放过程的一致性,纤维铺放压辊必须在适应芯模型面的同时具有较好的压紧力分布均匀性。鉴于此,对不同弹性模量的压辊材料进行了试验分析,薄膜压力传感器及超声显微镜测试结果表明,低弹性模量的压辊材料变形较大,较好地适应了芯模表面,压力分布相对均匀且可以减少铺层的层间孔隙数量,硅橡胶压辊比聚乙烯压辊压紧力分布均匀性提高了50%~60%,铺层孔隙率降低了92.1%。针对孔隙分布主要集中在压辊两端及压紧力在压辊两端下降幅度较大的问题,采用ANSYS Workbench对压辊端部进行斜端面优化,得到最优倾斜角度为20°;测试结果表明斜端面压辊压力分布均匀性比直断面压辊提高了42.9%,铺层孔隙率下降了51.6%。     

Determination of thermal expansion coefficients for unidirectional fiber-reinforced composites

In the present work, the coefficients of thermal expansion（CTEs） of unidirectional（UD）fiber-reinforced composites are studied. First, an attempt is made to propose a model to predict both longitudinal and transverse CTEs of UD composites by means of thermo-elastic mechanics analysis. The proposed model is supposed to be a concentric cylinder with a transversely isotropic fiber embedded in an isotropic matrix, and it is subjected to a uniform temperature change. Then a concise and explicit formula is offered for each CTE. Finally, some finite element（FE） models are created by a finite element program MSC. Patran according to different material systems and fiber volume fractions. In addition, the available experimental data and results of other analytical solutions of CTEs are presented. Comparisons are made among the results of the cylinder model,the finite element method（FEM）, experiments, and other solutions, which show that the predicted CTEs by the new model are in good agreement with the experimental data. In particular, transverse CTEs generally offer better agreements than those predicted by most of other solutions.     

航空碳纤维树脂基复合材料加筋板压缩屈曲及后屈曲性能

开展了复合材料加筋板轴压稳定性实验,对加筋板的屈曲及后屈曲性能、破坏模式和后屈曲失效表征进行了研究.实验结果表明加筋板在轴压下具有良好后屈曲承载潜能,破坏载荷约为屈曲载荷的2.2倍;其屈曲模式为筋条间蒙皮首先发生屈曲失稳,筋条在整个承载过程中保持直线,起到“屈曲分隔”的作用.通过对加筋板屈曲及后屈曲性能的理论分析,得出的理论屈曲载荷和理论破坏载荷与实验结果相对误差均小于8%,并确定了在后屈曲过程中蒙皮中心挠度的变化规律和轴向载荷的面内分布特征.      

复合材料夹层结构在航空领域的应用

详细描述了复合材料夹层结构及几种常用芯材的性能特点,综合分析了复合材料夹层结构在飞机上的应用案例,对各种夹层结构芯材成型工艺的重点、难点进行了探析,得到了复合材料夹层结构的性能概况及使用工艺要求,可为复合材料夹层结构设计、制造提供参考。     

复材制件数字化制造及先进设备的应用

随着复材零件结构的日益复杂,传统复合材料生产模式很难满足其精准化要求,复合材料数字化软件的开发使零件的制造过程更加便捷,同时能够满足对零件尺寸精准的验收技术要求。分别以某型号壁板蜂窝夹层件两类典型的零件作为研究实例,利用数字化软件对制造过程进行优化,开展数字化制造可行性研究,辅以数控下料机、激光铺层定位仪、自动铺带机等先进的数字化设备,更好地保障飞机构件外形的精度。复合材料制件实行数字化制造后,不但降低了生产成本保证了零件产品的质量,而且有效推进了复合材料零件制造技术的发展。