高性能与高功能纤维的发展

概述了用于复合材料增强体的高性能纤维和具有各种物理与化学功能用途的高功能纤维的进展现状并推测其发展趋势。     

CS-01高空台推力测量和校准装置研制

推力是涡喷涡扇发动机高空模拟试验的重要测量参数之一。CS－01高空台原推力测量采用杠杆、砝码、测力秤系统，现采用原位校准，液压加载、应变式推力传感器来测量和校准，从而消除了“高度差”的影响，降低了稳态推力测量系统的测量不确定度。     

发动机燃油流量现场校准装置

叙述了活塞式燃油流量现场校准装置的工作原理、系统组成、结构特点和技术性能 ,以及计量检定方法与数据处理。鉴定表明 ,装置结构合理、技术先进、功能强、量程范围宽、已达0 .1级准确度 ,不仅适用于发动机试车台燃油流量测量现场校准 ,而且也可供计量部门作为液体流量校准装置使用     

舰载飞机着舰拦阻动力学研究综述简

 拦阻着舰过程通常被认为是舰载飞机事故率最高的阶段,因此,自从有了航空母舰和舰载飞机,拦阻着舰动力学就一直是国内外相关研究人员的研究热点。本文从拦阻钩、拦阻装置和起落架3个关键部件着手,比较详细地论述了舰载飞机着舰拦阻涉及到的关键动力学问题及其研究现状,重点对拦阻钩弹跳动力学及其载荷分析、拦阻索动力学及其载荷分析、下沉速度、非对称拦阻对起落架载荷的影响、拦阻系统动力学等方面进行了综述。最后,对着舰拦阻动力学研究的发展趋势进行了展望。     

加力燃油计量装置的AMESim 仿真研究

为获得加力燃油系统数字化仿真与性能验证平台,采用功能划分的方法分析了典型计量装置的功能模块,确定了伺服阀-随动活塞、计量活门-等压差活门是决定计量装置动态特性的主要组成部分,对其进行了数学建模。鉴于获得的数学模型描述系统特性时缺乏相关元件特性参数的设计依据,建立了由计量活门、等压差活门、电液伺服单元等组成计量装置的AMESim模型,计算主要结构参数后仿真分析了其稳态和动态特性。结果表明:基于控制系统构成的加力燃油计量装置功能划分与数学建模可为仿真研究与参数设计提供指导,AMESim可用于动态过程仿真与性能预测。     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

Determination of thermal expansion coefficients for unidirectional fiber-reinforced composites

In the present work, the coefficients of thermal expansion（CTEs） of unidirectional（UD）fiber-reinforced composites are studied. First, an attempt is made to propose a model to predict both longitudinal and transverse CTEs of UD composites by means of thermo-elastic mechanics analysis. The proposed model is supposed to be a concentric cylinder with a transversely isotropic fiber embedded in an isotropic matrix, and it is subjected to a uniform temperature change. Then a concise and explicit formula is offered for each CTE. Finally, some finite element（FE） models are created by a finite element program MSC. Patran according to different material systems and fiber volume fractions. In addition, the available experimental data and results of other analytical solutions of CTEs are presented. Comparisons are made among the results of the cylinder model,the finite element method（FEM）, experiments, and other solutions, which show that the predicted CTEs by the new model are in good agreement with the experimental data. In particular, transverse CTEs generally offer better agreements than those predicted by most of other solutions.     

对流层折射修正中水汽压公式对比研究

针对当前对流层大气折射效应评估计算的工程应用中,水汽压的计算方法不尽统一、精度参差不齐的现状,分别在-50℃～0℃气温范围内利用各平冰面饱和水汽压公式、在0℃～50℃气温范围内利用各平液面饱和水汽压公式对大气折射率湿项进行了仿真计算,通过对仿真结果的比较可知：在平冰面和平液面情况下,Buck（巴克）1981公式和Buck1996公式与Goff-Gratch（戈夫-格雷奇）公式的偏差均较小,计算精度较高,建议作为测控系统外测数据处理中大气折射修正的首选经验公式;该分析结果也可为其他需要考虑水汽影响的工程领域提供参考.     

基于空间环境下细胞预处理装置的研制

生物样品的分离纯化是生命科学研究中的重要环节。在常规地面分离方法中,往往用到离心、萃取等操作,然而在空间微重力条件下,常规的方法无法进行,需要采用特定的方法和技术进行研究。以实现空间环境下细胞内生物大分子的分离为目标,研制了一种可以自动化一体化的装置,其先对细胞样品进行清洗、裂解并释放内溶物,然后在超滤分离池中将生物大分子和小分子化合物进行分离。通过对分离获得的大分子物质如蛋白质的回收率来优化仪器装置的最佳运行条件。结果表明,所研制的装置通过泵在一定频率下的切换,可使裂解体系在膜上进行反复的往返振动,从而使裂解液与细胞进行充分的接触,有效提高了细胞裂解的程度,提高了大分子蛋白的回收率,并通过条件优化确定了装置的最佳运行条件。     

SiC_p/Al材料力学行为研究的进展

碳化硅颗粒增强铝基复合材料(SiCp/Al)在材料科学和力学领域被关注,也是航天航空、汽车、电子仪表等领域关注较多的潜力材料。本文主要介绍SiCp/Al的增强机理和破坏机制,结合数值计算方法的进展从增强机理、破坏机理、建模方法和本构模型几个方面综述力学研究的若干进展。