超声速串列静叶积叠优化分析

在进口超声速、气流转折角大的高负荷条件下,静叶通道中激波强度高,激波、附面层干扰引起的损失大,且静叶中三维流动引起的径向载荷分布不均匀,易产生角区分离。叶片积叠优化是提高风扇性能的一项有效技术。采用数值模拟的方式研究了不同积叠形式对优化串列静叶沿展向激波结构,改善叶排间流动匹配的作用。三维流动对比分析可以得出:高负荷串列静叶采用正弓形积叠,叶片展向载荷分布合理,静叶端壁角区分离损失减小,前后叶片排流动匹配较好,风扇性能进一步提高。     

一种减少失速保护虚警率的混合滤波方法

针对飞机失速保护设计过程中易出现虚警的情况,提出一种基于FIR和传统滤波器相结合的混合滤波方法。结合飞机本体的运动特征,对参与失速保护逻辑运算的两个重要参数,即侧向加速度和迎角信号进行频率分析,基于信号的特征设计混合滤波器,然后采用Simulink滤波工具箱设计滤波器对信号进行滤波处理。仿真结果表明该方法能够减少虚警率的发生,特别是大背景噪声下的虚警率能够得到较好抑制,验证了滤波器设计正确性,从而提高失速保护功能对适航条款符合性。该滤波器设计方法,不但可以有效解决本文提到的问题,对于其他涉及信号处理的系统设计同样具有借鉴意义。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

基于小波变换的测距仪脉冲干扰抑制方法

为解决L频段数字航空通信系统以内嵌方式部署在L频段测距仪频道间而产生的测距仪系统干扰宽带航空数据链接收机的问题,基于小波变换去噪方法提出L-DACS1系统测距仪脉冲干扰抑制接收机,利用LDACS1及测距仪脉冲干扰信号特性,基于小波变换去噪方法重构测距仪脉冲信号,然后在时域内消除测距仪脉冲干扰信号。计算机仿真结果显示:在高斯白噪声信道与多径信道环境下,所提出L-DACS1接收机方案可有限消除测距仪脉冲干扰,提高链路传输的可靠性。     

S形进气道锤击波荷载特性分析

利用基于改进的延迟分离涡模拟（IDDES）方法,对亚声速和超声速来流条件下某S形模型进气道进行了非定常计算,研究了发动机喘振所产生的瞬时高压波形对锤击波传播规律的影响.结果表明:锤击波产生后沿进气道迅速向前传播,运动过程中锤击波的运动速度基本保持不变,但强度不断增强.同时受气流离心力的影响,S形进气道弯曲段半径较大一侧壁面受到的锤击波气动荷载值更大.发动机喘振所产生的瞬时高压的加载梯度增加使得锤击波传播速度及强度增强,而压力卸载方式对锤击波强度的影响不明显.在亚声速和超声速来流条件下,增加瞬时高压峰值均使得锤击波荷载强度显著增强,并近似符合二次函数分布规律,而且超声速来流条件下锤击波强度较亚声速来流更强.      

基于响应面法的短距/垂直起降飞机近地面升力损失

建立了短距/垂直起降(S/VTOL)飞机近地面升力损失的流场计算模型.通过数值模拟得出特定升力布局的飞机近地面状态各工况的升力损失.采用响应面法获得了飞机升力损失关于喷管落压比（NPR）、来流速度及飞机高度的2阶响应曲面函数及显著影响飞机升力损失的关键因素.并分析了喷管落压比、来流速度及飞机高度对飞机升力损失的交互影响作用,优化得出给定工况范围内升力损失最小的工作点.研究表明:仅考虑单因素影响时,升力损失随高度、落压比的增大而减小,随来流速度的增大而增大;考虑两因素交互作用时,高度与落压比及来流速度与落压比对升力损失存在交互影响,而高度与来流速度对升力损失无交互影响;优化获得的升力损失最小的工作点是飞机距地面高度为9D（D为喷管直径）、喷飞机高度为3、来流速度为0m/s,此时的升力损失为1.3%.      

进口探针支杆对1.5级压气机气动性能的影响

为了评估进口测试探针支杆对压气机气动性能的影响,定常计算了包含不同直径、轴向位置、周向位置及形状的探针支杆的1.5级压气机特性线。结果表明,较无进口探针支杆的工况,带探针支杆的压气机特性线整体向左下方偏移。圆柱型支杆较迎风面积相同的长条型支杆而言,使压气机特性线衰减更严重;随支杆直径增加,压气机特性线偏移量增大,5mm,10mm及20mm的支杆使压气机平均效率分别降低0.8%,1.32%及2.28%;支杆周向位置、轴向位置对压气机特性线无影响。分析定常及非定常数值计算结果发现,当支杆尾迹引起的进口气流角脉动位于进口导叶不敏感角范围内时,导叶的整流作用使导叶下游压气机性能不受进口支杆的影响。     

激励参数对合成射流控制压气机流动分离的影响

对吸力面施加合成射流激励的高负荷压气机静叶栅展开数值模拟,系统地研究不同激励参数对单缝合成射流改善叶栅气动性能的影响,并探索分段式合成射流控制流动分离的有效性。研究结果表明,单缝合成射流对栅内流动的作用效果主要取决于两个因素:射流切向动量注入带来的气动性能改善与射流输运过程的附加流动损失。单缝合成射流具有较为宽广的有效频率范围,当激励频率等于主流流过叶型的频率且射流满足有效激励动量要求时,对叶栅气动性能的改善效果最佳,总压损失降低约14.26%。分段式合成射流能够较好地适应不同叶高处分离起始点沿轴向变化对最佳流动控制位置的要求,在不增加有效射流面积的前提下可较单缝射流更为有效地控制流动分离,此时的损失降低幅度高达15.84%,从另外一个角度证实了激励位置对于非定常激励的重要性。     

液体火箭发动机充液导管流固耦合动力学特性

为了深入研究流固耦合（FSI）作用对液体火箭发动机充液导管频率特性的影响,采用传递矩阵法(TMM)建立了空间导管流固耦合动力学计算模型.针对真实发动机导管开展了传递矩阵模型与传统基于附加质量的有限元(FEM)（非耦合）模型仿真计算以及模态试验验证,比较了管径、壁厚等结构参数对导管流固耦合作用的影响.结果表明:在流固耦合作用下,导管各阶谐振频率减小、而对应的流体振荡与结构振动幅值增大.管径对导管低阶频率特性的影响较壁厚对其影响更大.对于该算例,当管径大于设计值30%后,耦合作用引起的1阶频率误差高于10%,此时流固耦合不能忽略;而壁厚对1阶谐振频率的影响则小于8%.