基于LES方法的平板非定常激波/湍流边界层干扰研究

以高超声速发动机进气道湍流分离控制为应用背景,采用大涡模拟(LES)方法进行马赫数为3.0(唇口附近马赫数约为3.0)的激波/湍流边界层干扰(SWTBLI)流场机理研究.利用扰动循环引入的方法,先得到充分发展湍流场,然后根据斜激波关系式引入激波的方法进行激波/湍流干扰模拟.研究结果显示:充分发展湍流场在激波作用下产生逆...     

非线性EASM在激波与湍流边界层相互作用中的数值应用

采用基于k-ω湍流模型的非线性显式代数应力模型(EASM)对超燃冲压发动机常用的超声速凹槽、压缩拐角和侧壁压缩进气道简化模型的激波与湍流边界层的相互作用进行了计算,主要研究了EASM 模型对壁面压强、摩阻、Stanton数和壁面摩擦力线的计算精度,计算结果与SST(shear stress transport)模型进行...     

变截面梁的变矩和位移计算法

变截面梁的控制方程为变线数微分方程，一般只能用各种近似方法求解，而且比较复杂。对于梁式构件，本文不求解变系数方程，而是用力法，在力法方程中，主、副系数和自由项的莫尔积分使用积分表，可以方便而且精确地求出变截面梁的弯矩和位移。     

简易U型弯曲模设计

本文介绍了一种简易的U型弯曲模具的设计方法,具有结构简单、制造容易、节约材料、重量轻的特点,在小批量生产中有借鉴意义。     

RAPID TRANSFER ALIGNMENT USING FEDERATED KALMAN FILTER

The dimension number of the centralized Kalman filter (CKF) for the rapid transfer alignment (TA) is as high as 21 if the aircraft wing flexure motion is considered in the rapid TA. The 21-dimensional CKF brings the calculation burden on the computer and the difficulty to meet a high filtering updating rate desired by rapid TA. The federated Kalman filter (FKF) for the rapid TA is proposed to solve the dilemma. The structure and the algorithm of the FKF, which can perform parallel computation and has less calculation burden, are designed.The wing flexure motion is modeled, and then the 12-order velocity matching local filter and the 15-order attitud ematching local filter are devised. Simulation results show that the proposed EKE for the rapid TA almost has the same performance as the CKF. Thus the calculation burden of the proposed FKF for the rapid TA is markedly decreased.     

BUCKLING OF SPATIAL CURVED RODS WITH CIRCULAR CROSS-SECTIONS

Formulae for determining Green strain of an initially curved and twisted rod with circular cross-sections are derived by using the natural (curvilinear) coordinate system. Finite element analyses are performed for the flexural buckling of initially curved and twisted thin rods under simultaneous action of axial force and torque. Numerical examples demonstrate that the given formulae are correcte. Some numerical results are compared with existing analytical solutions and data obtained by commercial FE software. The convergence of the proposed curved element is better than that of elements in the commercial FE software. It is shown that good accuracy and convergency are achieved by solving three-dimensional problems.     

马赫数3到7的变化比热正冲波的改进解析解及近似解

作者提出的变化热正冲波改进解析解，延伸用于马赫数从３到７情况，求出过冲波后全部气动参数，接马赫数间隔为１列表给出。并附列定比热结果误差。同时提出了只取初温到终温平均比热比ｋ１２近似解，平行列出结果及误差。     

从叶轮机械流场到对应的数学模型

建立或描述叶轮机械流场模型研究的基础上，对叶轮机械复杂流动反问题，压气机气动稳定性与跨音风扇后掠空气动力学激波结构模型等三个方面作了进一步的探讨。     

空腹铝型材与板料弯曲模具设计

本主要讨论空腹铝型材弯曲工艺的关键技术，分析了弯曲缺陷产生的原因，设计了一副实用的空腹铝型材弯曲模。