Zn-Al-Si钎料钎焊铜/铝接头显微组织及性能研究

采用Zn-14.1Al-0.9Si和Zn-21.5Al-1.5Si两种钎料钎焊获得铜/铝接头,研究了Cu/Zn-Al-Si/Al接头Cu母材/钎缝界面结构、钎缝中心区显微组织、接头抗剪切性能和断口形貌.研究发现,Cu/Zn-14.1Al-0.9Si/Al接头和Cu/Zn-21.5Al-1.5Si/Al接头界面结构均为Cu/扩散层/Al4.2Cu3.2Zn0.7,其中Al4.2Cu3.2Zn0.7化合物层厚度分别为1～2 μm和3～4μm.2种铜/铝接头钎缝中心区均由α-Al固溶体,η-Zn固溶体,Zn-Al共晶和Si单质组成,未发现脆性CuAl2化合物.由于具有较薄的界面化合物层,在剪切力作用下,Cu/Zn-14.1Al-0.9Si/Al接头断裂一部分起源于Al4.2Cu3.2Zn0.7化合物层,另部分起源于界面扩散层,而Cu/Zn-21.5Al-1.5Si/Al接头断裂均起源于较厚的Al4.2Cu3.2Zn0.7化合物层.因此,Cu/Zn-14.1Al-0.9Si/Al接头的抗剪切强度高于Cu/Zn-21.5Al-1.5Si/Al接头,分别为60.1MPa和55.6MPa.     

某型航空发动机宽弦风扇叶片强度分析

针对某型航空发动机,考虑到离心力和气动力共同作用的影响,对该型发动机风扇叶片进行了有限元建模和强度分析,其中对气动力的加载进行了适当的简化。计算结果表明,该型叶片具有较高的静强度储备;应力集中区域在风扇叶片叶盆靠近叶根的区域,是叶片的几何形状以及离心力和气动力共同作用的结果。     

S型进气道隐身与气动综合特性数值分析

针对S型进气道弯度对其隐身气动特性影响程度的问题,利用CAD软件对进气道进行参数化建模,通过改变进、出口的中心偏移量实现对进气道弯度的改变。采用数值仿真方法分别研究了进气道前向电磁散射特性和进气道流场及气动特性。仿真结果表明,进气道弯度增加对隐身特性和气动特性的影响是完全相反的,并进一步分析出这一现象的产生机理,对进气道的隐身气动一体化设计具有指导性意义。     

一种减少失速保护虚警率的混合滤波方法

针对飞机失速保护设计过程中易出现虚警的情况,提出一种基于FIR和传统滤波器相结合的混合滤波方法。结合飞机本体的运动特征,对参与失速保护逻辑运算的两个重要参数,即侧向加速度和迎角信号进行频率分析,基于信号的特征设计混合滤波器,然后采用Simulink滤波工具箱设计滤波器对信号进行滤波处理。仿真结果表明该方法能够减少虚警率的发生,特别是大背景噪声下的虚警率能够得到较好抑制,验证了滤波器设计正确性,从而提高失速保护功能对适航条款符合性。该滤波器设计方法,不但可以有效解决本文提到的问题,对于其他涉及信号处理的系统设计同样具有借鉴意义。     

高超声速飞行器进气道压缩面逆向设计方法

针对高超声速飞行器进气道压缩面问题,首先研究了激波理论的逆向算法,以此为基础提出了进气道的等强度和等熵压缩面的逆向设计方法,并采用此方法设计了以进气道出口气流参数为设计参数的高超声速飞行器进气道压缩面,然后对两种压缩面进行了性能分析和数值仿真.结果表明:通过逆向设计方法设计进气道压缩面是可行的,其相对于传统方法耗时大大减少;理论计算表明相同设计条件下两压缩面几何参数基本一致,而来流参数也基本不变,设计点下等熵压缩面总压恢复系数高出等强度压缩面6.3%.数值仿真验证了该方法的可行性并研究了非设计状态下两种压缩面的各项性能参数,同时对比了不同马赫数下进气道内部波系分布和气流均匀性.      

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

采用排间界面静压约束伴随方法的多级压气机叶片优化

为解决伴随优化应用在多级压气机中出现的优化工况点漂移问题,在前期薄层N-S方程伴随方法基础上,对目标函数——出口熵增不仅施以质量流量、总压比约束,还添加排间界面静压展向分布作为新的约束条件.以某5级压气机为对象,对其中第1级转、静叶分别在首1.5级和全5级压气机环境下进行了优化.结果表明,施加排间界面静压展向分布约束能够显著解决优化工作点漂移问题,优化后5级压气机的效率提高0.4个百分点.      

大展弦比机翼非线性颤振分析与优化

<正>气动弹性问题一直以来都困扰着飞行器设计人员,现代飞机远没有摆脱气动弹性问题所带来的困扰,国内外研究结果表明,气动弹性优化设计能有效的改善机翼的气动弹性性能,进而提高飞机的整体性能,已成为现代飞机设计过程中必不可少的环节之一。随着先进的复合材料在飞机上得到广泛的应用,针对复合材料机翼的优化研究,得到了越来越多学者的关注。合理的优化可提高飞机发散速度甚至消除发散现象。在复合材料机翼的优化设计     

基于我国深空站三向测量模式的数据精度分析

为了验证我国深空站三向测量模式的正确性,以同步星跟踪试验中的测量数据为基础,建立了站间同步修正算法和三向测量观测模型,通过与同步卫星的精密星历反算测量值比较,得到了测量数据的标定参数,结果表明,我国深空站测控能够实现dm级的测量精度,明显优于“嫦娥二号”测量的水平;同时利用测量数据进行定轨策略分析,最终实现了10 m量级的同步卫星定轨精度.分析结果为“嫦娥三号”探测器实施有效测控提供了依据.