全文获取类型
收费全文 | 1112篇 |
免费 | 200篇 |
国内免费 | 121篇 |
专业分类
航空 | 926篇 |
航天技术 | 162篇 |
综合类 | 130篇 |
航天 | 215篇 |
出版年
2024年 | 11篇 |
2023年 | 38篇 |
2022年 | 61篇 |
2021年 | 42篇 |
2020年 | 62篇 |
2019年 | 60篇 |
2018年 | 40篇 |
2017年 | 40篇 |
2016年 | 62篇 |
2015年 | 62篇 |
2014年 | 70篇 |
2013年 | 67篇 |
2012年 | 71篇 |
2011年 | 73篇 |
2010年 | 59篇 |
2009年 | 77篇 |
2008年 | 66篇 |
2007年 | 56篇 |
2006年 | 51篇 |
2005年 | 41篇 |
2004年 | 53篇 |
2003年 | 30篇 |
2002年 | 30篇 |
2001年 | 26篇 |
2000年 | 27篇 |
1999年 | 11篇 |
1998年 | 21篇 |
1997年 | 16篇 |
1996年 | 18篇 |
1995年 | 14篇 |
1994年 | 16篇 |
1993年 | 13篇 |
1992年 | 11篇 |
1991年 | 9篇 |
1990年 | 11篇 |
1989年 | 13篇 |
1987年 | 2篇 |
1986年 | 1篇 |
1985年 | 1篇 |
1982年 | 1篇 |
排序方式: 共有1433条查询结果,搜索用时 15 毫秒
841.
843.
844.
典型型材拉弯过程中因存在回弹而不利于模具的设计制造.通过经验法给出拉弯回弹值并进行修模后所拉弯成形的零件不符合制造技术要求,且反复试验有很大的不确定性,存在制造风险.本文通过前期采用有限元仿真技术对典型型材拉弯成形过程进行模拟分析,确定各类参数对零件变形的影响,预测零件在拉弯成形过程中的变形情况,获得型材在理论载荷状态... 相似文献
845.
In this paper, a novel study on performance of closed loop pulsating heat pipe(CLPHP)using ammonia as working fluid is experimented. The tested CLPHP, consisting of six turns, is fully made of quartz glass tubes with 6 mm outer diameter and 2 mm inner diameter. The filling ratio is50%. The visualization investigation is conducted to observe the oscillation and circulation flow in the CLPHP. In order to investigate the effects of inclination angles to thermal performance in the ammonia CLPHP, four case tests are studied. The trends of temperature fluctuation and thermal resistance as the input power increases at different inclination angles are highlighted. The results show that it is very easy to start up and circulate for the ammonia CLPHP at an inclining angle.The thermal resistance is low to 0.02 K/W, presenting that heat fluxes can be transferred from heating section to cooling section very quickly. It is found that the thermal resistance decreases as the inclination angle increases. At the horizontal operation, the ammonia CLPHP can be easy to start up at low input power, but hard to circulate. In this case, once the input power is high,the capillary tube in heating section will be burnt out, leading to worse thermal performance with high thermal resistance. 相似文献
846.
847.
张宝柱孙洁琼 《民用飞机设计与研究》2014,(2):16-19,79
民用飞机后机身与尾段的对接往往选择球面框(后压力隔框)位置,球面框是机身气密线的末端,该处的对接设计需要从传力、重量、成本、装配、维修、排水等多方面进行考虑,是民用飞机机体结构设计中非常重要的一个环节。针对民用飞机中后机身与尾段的连接特点,从传力等考虑要素入手,介绍了目前国际上典型机型的成熟方案,并进行方案优缺点分析、比较和总结,为我国民用飞机结构设计提供借鉴。 相似文献
848.
首先,给出弹目距离与视线角控制的二阶欠驱动系统的标准形式,选取这两个相关的系统状态分别构造滑模平面,滑模面能够保证系统状态的跟踪;然后,选取李雅普诺夫函数,采用李雅普诺夫稳定定理求取最终的控制量,保证两个滑模面渐近稳定,实现对撞击时间与撞击角度的同时控制;最后,在时间控制基本完成后,切换为角度精确控制。 相似文献
849.
刘兴明 《海军航空工程学院学报》2011,26(6):691-694
为了减少反舰导弹受冲淡干扰的几率,要求末制导雷达在保证捕捉概率的同时尽量减小角度搜索范围。为此,提出了末制导雷达捕捉目标所需最小角度搜索范围模型,推导了最小角度搜索范围表达式及其对应的最佳开机距离表达式。在不同的探测距离下,以高亚声速反舰导弹为例进行了仿真计算。结果表明,最小角度搜索范围在+30°之内,小于某些反舰导弹... 相似文献
850.
利用已取得的火箭圆柱壳板和滚弯机三轧辊之间弹塑性力学关系的研究成果 [1 ] [2 ] [3 ] ,进一步探索及研究实际工况下产生箭壳板滚弯直线度误差的机理 ,并提出滚弯机改进设计的方法。研究表明 ,按推荐设计方法改进滚弯机可使箭壳板滚弯直线误差大幅度下降。 相似文献