非均匀入口与化学非平衡效应对尾喷管性能的影响研究

基于煤油燃料超燃冲压发动机尾喷管,对均匀入口和非均匀入口、冻结流动模型和化学非平衡模型下的尾喷管内流动进行数值模拟,采用两方程RNG k-ε湍流模型对三维NS方程组进行求解,获得非均匀入口与化学非平衡效应对尾喷管性能的影响。计算结果表明,尾喷管内流动非均匀性由尾喷管非对称膨胀和燃烧室出口非均匀等因素构成,尾喷管入口流动参数非均匀分布对尾喷管推力、升力及俯仰力矩均有影响,算例中非均匀入口使得尾喷管净推力相对于均匀入口增加了1.2%左右;尾喷管性能受化学非平衡效应的影响,非平衡流动模型下的其净推力计算结果相对于冻结流动模型增加3%~4%。     

超燃冲压发动机燃烧室主动冷却设计研究

超燃冲压发动机燃烧室主动冷却模型制造和热考核试验的费用高昂、周期长,为了降低试验风险,采用三维计算和经济的验证试验相结合的方法开展了超燃冲压发动机燃烧室主动冷却设计。冷却结构基本参数设计和侧壁冷却流动设计是确定设计方案的两大基础,前者采用三维传热计算结合冷却面板传热验证试验完成,后者采用超临界燃料流动三维并行计算结合水流动验证试验完成。在此基础上,经过多轮的结构设计与三维传热及强度计算评估迭代,确定了最终的燃烧室主动冷却结构。设计的主动冷却燃烧室在来流马赫数2.5,总温1700K条件下成功通过200s热考核试验,表明所采用的设计方法、验证试验和计算工具是有效和可信的。     

Transient simulation of regression rate on thrust regulation process in hybrid rocket motor

The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–solid coupling is considered between the solid grain surface and combustion gas.Dynamic mesh is used to simulate the regression process of the solid fuel surface. Based on this model, numerical simulations on a H2O2/HTPB(hydroxyl-terminated polybutadiene) hybrid motor have been performed in the flow control process. The simulation results show that under the step change of the oxidizer mass flow rate condition, the regression rate cannot reach a stable value instantly because the flow field requires a short time period to adjust. The regression rate increases with the linear gain of oxidizer mass flow rate, and has a higher slope than the relative inlet function of oxidizer flow rate. A shorter regulation time can cause a higher regression rate during regulation process. The results also show that transient calculation can better simulate the instantaneous regression rate in the operation process.     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

Storage life of silicone rubber sealing ring used in solid rocket motor

It is urgent to carry out detailed research on storage performance of rubber sealing ring to get the criterion for its storage life. This paper acquires material ageing regularity by theoretical analysis and experimental confirmation. On this condition, failure mode and failure criterion of typical sealing structure is studied, and the failure mechanism is found. Thus by analyzing the stress distribution, the relationship between ageing state and sealing condition is established. Rationalization proposal is put forward and storage life of sealing ring is evaluated. The research mentionedabove has special reference to the design of sealing structures and can provide reference for prolonging their service life.     

激波聚焦诱导气液两相爆震燃烧的数值模拟

对以激波聚焦和增加障碍物方式诱导煤油-空气气液两相爆震燃烧的过程进行了数值模拟.采用欧拉-拉格朗日方法建立了脉冲爆震发动机(PDE)中气液两相流的喷射、雾化、掺混过程.研究发现环形爆震波在爆震管凹腔内经过反射、汇聚后能够引燃可燃混合物.而在障碍物处,激波的反射和再反射聚焦能够形成高温高压点(2700K,25MPa),产生局部爆炸,有助于形成稳定的脉冲爆震燃烧(波面速度为1900m/s,温度为2 950K),有效地缩短由缓燃向爆震转变(DDT)距离至0.45m.     

基于自适应粒子滤波的涡扇发动机故障诊断

针对涡扇发动机非线性、非高斯的特点,提出了一种自适应的粒子滤波算法用于涡扇发动机气路部件突变故障的诊断.为了减小算法的计算量并且保证滤波精度,分析了滤波精度和样本数目的关系,提出根据滤波过程中状态的方差自适应地调整粒子数,在保证一定的滤波精度下可以有效地减少滤波过程中使用的粒子数,提高了算法的实时性.同时,引入扩展卡尔曼滤波(EKF)用于更新粒子,产生重要概率密度函数,在一定程度上避免了粒子的退化.通过某型涡扇发动机的仿真分析表明:改进的算法相比标准粒子滤波算法用于涡扇发动机气路部件故障诊断时,参数估计的方均根误差减小了50%左右,且算法的计算量减小了30%.     

基于高速慢车的航空发动机快速响应控制

针对传统航空发动机响应速度慢,难以在紧急事件中用于控制受损飞机完成起降过程的问题,采用高速慢车控制模式来提升发动机加速性能,通过增加发动机在慢车时高压压气机转速,为加速前期提供更大的燃油流量,从而缩短发动机从慢车至最大状态的加速时间。为保证慢车时高压转子转速提高的同时发动机推力和稳定裕度不变,通过修改高压压气机可调导叶控制计划来调整高压转子工作点。仿真结果显示,与原有控制相比,采用高速慢车快速响应控制模式的发动机加速上升时间从原来的2.00s缩短至1.86s,而高压压气机最小喘振裕度仅由16.01%下降至14.81%,同时慢车推力基本保持不变。     

超燃冲压发动机旋转斜坡概念研究

基于斜坡增强混合及旋转冲压的设计思想,提出一种旋转斜坡概念,即通过斜坡旋转产生大尺度旋涡及旋转运动激波来增强混合。采用Fluent软件求解URANS方程,对旋转斜坡非定常流场开展了数值模拟研究,分析了斜坡旋转速度对燃烧室的流场特征、涡量、总压损失等性能的影响。结果表明斜坡旋转促进了凹腔剪切层的振荡,并在凹腔内形成了较强烈的流向旋涡。当旋转速度54.3r/min时,斜坡旋转导致的流向涡量峰值约是无旋状态下的4倍左右,总压恢复系数比斜坡静止状态最大降低约10%。     

消光漆在光学系统的国内外应用

简单地列举了国内外一些消光漆的应用情况,阐述了消光漆的消光性能指标的测定方法,同时对

国内外的一些消光漆的消光性能进行了比较。