加力燃油计量装置的AMESim 仿真研究

为获得加力燃油系统数字化仿真与性能验证平台,采用功能划分的方法分析了典型计量装置的功能模块,确定了伺服阀-随动活塞、计量活门-等压差活门是决定计量装置动态特性的主要组成部分,对其进行了数学建模。鉴于获得的数学模型描述系统特性时缺乏相关元件特性参数的设计依据,建立了由计量活门、等压差活门、电液伺服单元等组成计量装置的AMESim模型,计算主要结构参数后仿真分析了其稳态和动态特性。结果表明:基于控制系统构成的加力燃油计量装置功能划分与数学建模可为仿真研究与参数设计提供指导,AMESim可用于动态过程仿真与性能预测。     

Multi-objective optimization of aircraft design for emission and cost reductions

Pollutant gases emitted from the civil jet are doing more and more harm to the environ- ment with the rapid development of the global commercial aviation transport. Low environmental impact has become a new requirement for aircraft design. In this paper, estimation method for emis- sion in aircraft conceptual design stage is improved based on the International Civil Aviation Orga- nization （ICAO） aircraft engine emissions databank and the polynomial curve fitting methods. The greenhouse gas emission （CO2 equivalent） per seat per kilometer is proposed to measure the emis- sions. An approximate sensitive analysis and a multi-objective optimization of aircraft design for tradeoff between greenhouse effect and direct operating cost （DOC） are performed with five geom- etry variables of wing configuration and two flight operational parameters. The results indicate that reducing the cruise altitude and Mach number may result in a decrease of the greenhouse effect but an increase of DOC. And the two flight operational parameters have more effects on the emissions than the wing configuration. The Pareto-optimal front shows that a decrease of 29.8% in DOC is attained at the expense of an increase of 10.8% in greenhouse gases.     

Design and experimental study of a micro-groove grinding wheel with spray cooling effect

The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming.     

一种基于光固化快速成型的飞机静弹性风洞试验模型设计方法

高速风洞静弹性模型设计和制造是静弹性风洞试验的一个关键。为解决模型设计周期长、制造费用高等问题,提出了一种基于立体光固化快速成型面向高速风洞大展弦比机翼静弹性模型研制方法。基于机翼刚度分布相似参数,采用机翼钢梁骨架和树脂蒙皮组合结构,通过优化结构尺寸完成静弹性模型结构设计;使用机械加工和快速成型技术完成模型制造,并通过地面刚度试验对加工模型进行了刚度分布验证。风洞试验结果表明：基于立体光固化成型技术设计和制造的静弹性风洞试验模型工程实用、可行,与传统静弹性模型研制过程相比,具有研制周期短、成本低而且不存在因填充物带来附加刚度的显著优势。     

C频段宽带线／圆极化器小型化设计

为适应C频段卫星测控通信车栽天线机动布站功能,须研制一种轴向尺寸小于1．2m的小型化天馈系统,针对该问题,对关键组件线／圆极化器进行小型化设计。在理论分析极化器原理的基础上,采用在聚四氟乙烯基材上打孔的方法使一种介质实现多种相对介电常数,设计了C频段收、发均覆盖575MHz带宽的小型化宽带极化器,在56％相对带宽内实现小型化,轴向尺寸缩短至常规极化器的1／a,经HFSS（HighFrequencySimulationSoftware,高频仿真软件）仿真计算,并与同频段常规极化器性能进行分析比较,结果表明：该极化器移相量与匹配性能良好,满足指标与使用要求。     

An extrapolation approach for aeroengine’s transient control law design

Transient control law ensures that the aeroengine transits to the command operating state rapidly and reliably. Most of the existing approaches for transient control law design have complicated principle and arithmetic. As a result, those approaches are not convenient for application. This paper proposes an extrapolation approach based on the set-point parameters to construct the transient control law, which has a good practicability. In this approach, the transient main fuel control law for acceleration and deceleration process is designed based on the main fuel flow on steady operating state. In order to analyze the designing feature of the extrapolation approach, the simulation results of several different transient control laws designed by the same approach are compared together. The analysis indicates that the aeroengine has a good performance in the transient process and the designing feature of the extrapolation approach conforms to the elements of the turbofan aeroengine.     

基于传声器阵列的航空发动机噪声源识别研究

为了实现新一代发动机的噪声源识别技术,对于测试所得到的民用飞机发动机的整体噪声数据,通过部件噪声分解方法,将其分解到各个部件,并且认识当代民用飞机发动机噪声源的基本特征.开发出利用发动机整机噪声数据的噪声源识别系统,采用反卷积法将波束成型法的结果作为中间声源,从中获取所需要的声源信息,使得最终的结果更加准确.通过获取的发动机整机噪声数据,验证传声器阵列技术的可行性,并且证明了系统的可行性和有效性.     

读来读往

CIMT将于4月22日在北京隆重开幕。面对后危机时代的挑战,中国已连续几年成为世界第一大机床消费国,本届展会更是盛况空前,代表世界顶尖技术水平的机床工具产品将大放异彩。本刊为此推出了"未来机床"、"未来刀具"、"未来测量"和"未来工厂"4期特别策划。本期是以"未来工厂"为主题的特别策划。封面文章介绍了数字化工厂技术的应用现状与趋势;专稿针对实现飞机全三维设计的     

科学实验卫星高速上行链路设计

为保障在卫星与地面之间开展空间量子科学实验的条件,必须为科学实验载荷建立一条星—地高速数据双向传输链路.通过跟踪CCSDS-SLS-NGU（空间数据系统咨询委员会-空间链路业务-下一代上行链路）工作组对NGU的研究进展,结合科学实验卫星有效载荷建立高速上行链路的需求,采用高带宽利用率调制技术、高效信道编码方式及适用的链路数据传输协议,设计了一种传输速率为1Mbit/s、误码率优于1×10-9的高速上行链路方案,并给出星载设备实现方案和地面初步测试结果.该方案在技术体制上兼容已有CCSDS规范,便于地面站及星载接收机实现,完全满足开展空间量子科学实验的需要.     

一种基于FPGA的全帧率图像处理方法

针对图像算法在FPGA内的硬件化实现问题,提出了一种全帧率处理的思路,并提供了两种具体的可供参考的设计方法——基于像素流缓冲的卷积核处理技术和基于相邻图像帧相关性的图像参数提取技术。通过其可以方便地设计并实现大部分空间域图像处理算法及其任意组合的硬件逻辑电路,并达到与图像输入帧率相同的处理速度。以Canny算子的硬件化实现为例验证了设计理念。实验结果表明,全帧率图像方法具有可操作性强、实时性好、符合结构化模块化设计的特点,特别适合于对实时性要求高的嵌入式视觉系统。