一种减少失速保护虚警率的混合滤波方法

针对飞机失速保护设计过程中易出现虚警的情况,提出一种基于FIR和传统滤波器相结合的混合滤波方法。结合飞机本体的运动特征,对参与失速保护逻辑运算的两个重要参数,即侧向加速度和迎角信号进行频率分析,基于信号的特征设计混合滤波器,然后采用Simulink滤波工具箱设计滤波器对信号进行滤波处理。仿真结果表明该方法能够减少虚警率的发生,特别是大背景噪声下的虚警率能够得到较好抑制,验证了滤波器设计正确性,从而提高失速保护功能对适航条款符合性。该滤波器设计方法,不但可以有效解决本文提到的问题,对于其他涉及信号处理的系统设计同样具有借鉴意义。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

层合板螺栓连接结构疲劳寿命预测

为了准确预测复合材料连接结构损伤的产生和扩展,基于单向板疲劳性能预测层合板螺栓连接结构疲劳寿命。用T300/BMP-316单向板试验数据对正则化疲劳寿命与剩余强度的参数进行拟合;在复合材料基体主控失效判据基础上增加纤维失效和分层失效判据,改进基于断裂韧性的失效准则判定损伤的产生和扩展;采用二级载荷疲劳寿命等效实现损伤的非线性累积,再对相应的损伤进行材料性能退化。预测结果与试验对比表明:对不同几何参数层合板连接结构的对数寿命预测与试验误差在5%以内,对不同应力水平下层合板连接结构的对数寿命预测与试验误差在10%以内,最终破坏模式及损伤区域的预测与试验结果吻合良好。     

基于结构动力学特性的损伤识别方法

基于等效模态应变/动能理论,提出了一种利用实际结构的测试数据识别结构中损伤位置的方法。在此基础上,研究了利用模型修正技术识别结构中损伤强度的方法。分别以一个单损伤平板结构和多损伤平板结构为例,通过仿真分析了以上方法的有效性。结果表明,以上方法可以有效识别结构中的损伤位置和损伤强度。     

基于概率统计的DS/FH系统干扰检测算法

基于时频分布的干扰检测算法是DS/FH（Direct Sequence/Frequency Hopping,直接序列扩频/跳频扩频）系统干扰检测的传统手段,针对其运算量大、实时性差,以及无法检测某些特殊干扰信号等问题,提出一种基于概率统计的干扰检测算法.通过统计DS/FH系统频谱图中各频率的幅值出现位置,以DS/FH信号与干扰信号频谱分布规律的差别为判决依据,完成DS/FH系统中干扰信号的检测.分析和仿真结果表明：该检测算法能够有效识别DS/FH系统中的典型干扰信号,与传统基于时频分布的检测算法相比,能够实现某些特殊干扰信号的有效检测;同时,由于该算法不需要进行复杂的时频联合分析,其运算复杂度大大降低,能够实现DS/FH系统干扰信号的快速检测.     

无线电高度表信号模拟器射频信号延时/衰减模块设计

无线电高度表程控信号模拟器是无线电高度表自动测试系统（ATE,ATS）的重要组成部分,而射频信号延时/衰减模块则是无线电高度表程控信号模拟器3个功能模块组件中的核心模块。研制了一种采用声表面波（SAW）延迟线作为射频信号延时器件、射频衰减器作为射频信号功率衰减器件,通过程控射频开关控制不同声表面波延迟线的切换,包含射频信号变频、放大等结构电路的无线电高度表信号模拟器射频信号延时/衰减模块。经无线电高度表自动测试系统的实际工程应用表明,该无线电高度表射频信号延时/衰减模块对C波段（4.2～4.4 GHz）射频调制信号的延时精度高、衰减范围大,体小、质轻,适合置于无线电高度表测试适配器内部使用,具有较高的工程应用价值。     

2.5维机织复杂结构件的静强度

采用宏细观结合方法,针对经纱和纬纱等材料组分可能发生的多种失效模式,分别建立了基于改进的Hashin准则的系统性的材料失效准则及不同失效模式下的刚度退化模型.引入逐渐损伤的思想,建立了2.5维机织复杂结构件静强度系统性分析方法.模拟并分析了材料经向拉伸和纬向拉伸的应力-应变曲线,与实验得到的材料应力-应变曲线相比,相同应变下应力误差不超过6.5%,具有较好的重合度;对2.5维机织压气机静子连接结构模拟件开展了逐渐损伤模拟,结果表明:结构损伤主要集中在叶根倒角附近,其中吸力面叶根处的基体压缩失效形式会引起结构大幅变形,是结构破坏的主要原因.      

基于EFFD方法的自然层流短舱优化设计

采用extended free-form deformation(EFFD)方法研究了自然层流(natural laminar flow,NLF)短舱的气动外形优化设计方法.使用基于Bernstein基函数的EFFD方法完成了NLF短舱剖面的参数化,利用基于k-εSST(shear stress transport)两方程湍流模型的γ-θ转捩模型进行自然转捩预测,结合EFFD、一种混合动网格方法、Kriging代理模型和改进的粒子群算法(particle swarm optimization,PSO)建立了针对NLF短舱气动外形的优化设计框架.采用该框架分别对通气NLF短舱和带动力NLF短舱进行优化设计.单独通气NLF短舱优化结果的外表面实现48%的层流,阻力系数比初始通气NLF短舱减小了0.0003.带动力NLF短舱的优化结果外表面保持了41%的层流.这些结果表明采用相关技术建立的优化设计框架在NLF短舱设计中具有一定应用价值.     

Coupling damage and reliability model of low-cycle fatigue and high energy impact based on the local stress–strain approach

Fatigue induced products generally bear fatigue loads accompanied by impact processes,which reduces their reliable life rapidly. This paper introduces a reliability assessment model based on a local stress–strain approach considering both low-cycle fatigue and high energy impact loads.Two coupling relationships between fatigue and impact are given with effects of an impact process on fatigue damage and effects of fatigue damage on impact performance. The analysis of the former modifies the fatigue parameters and the Manson–Coffin equation for fatigue life based on material theories. On the other hand, the latter proposes the coupling variables and the difference of fracture toughness caused by accumulative fatigue damage. To form an overall reliability model including both fatigue failure and impact failure, a competing risk model is developed. A case study of an actuator cylinder is given to validate this method.