飞机设计中发动机转子碎片非包容性设计

基于一种双发常规布局飞机进行飞机设计中发动机转子碎片非包容失效设计的研究,通过研究相关适航规章,以及相关咨询通告等文件,得出第3节到第7节所描述的对咨询通告AC20-128A适当裁剪的工程方法和步骤,并在实例机型设计中进行验证,缩短了飞机研制周期的同时,也表明在发动机转子碎片非包容失效事故发生后,飞机系统及机体结构等采取的设计措施、防范措施符合相关适航条例要求,也即结构剩余的强度、灾难性事件发生概率等满足AC20-128A第10条c中的定性和定量要求,表明该型实例飞机完全满足相关适航条例的要求,并获得中国民用航空局(CAAC)和美国联邦航空局(FAA)的认可。     

基于红外热像技术的涡轮叶片损伤评价研究进展

主动红外热像技术作为一种新型无损检测手段,具有高效率、无污染、易操作等特点,适合用于材料表面和近表面缺陷检测,因此在叶片类薄壁零件损伤评价方面有一定优势。当前基于主动红外热像无损检测技术的高温涡轮叶片损伤评价研究主要集中于热障涂层厚度检测、涂层脱粘检测、涂层界面处热生长氧化物检测以及叶片基体疲劳裂纹检测4个方面。但现有研究仍然面临热激励理论不完善、红外热像仪识别精度不够高以及热图处理方法有待改进等主要问题和困难。随着这些理论问题和技术困难的解决,主动红外热像技术呈现出人工识别缺陷向自动识别发展、定性检测向定量检测发展的趋势。总体而言,该技术未来在涡轮叶片损伤评价方面具有较大的应用潜力。     

X射线脉冲星导航硬件脉冲轮廓累积研究

为了在X射线脉冲星地面实验系统仿真源模拟产生X射线的基础上,能够快速稳定地得到脉冲轮廓,采用硬件历元叠加的方法获得脉冲轮廓。研究了用硬件实现历元叠加及其数据整合的算法,该算法首先在MATLAB现场可编程逻辑阵列(FPGA)中实现,再通过MATLAB硬件描述语言(HDL)代码生成模块把算法转换成HDL,经编译后获得配置硬件的Bit文件,最终在开发板FPGA上实现数据处理的硬件模块。一段时间内的光子到达时间数据通过MATLAB算法得到的脉冲轮廓数据与通过硬件模块处理后得到的数据结果存在误差,在单个时间窗口内误差最大值为2个光子数,误差平均值占光子数统计平均值的0.084%;两组统计的脉冲轮廓数据中不同数据占总数据个数的9.481%,这样的误差不影响后端模拟导航模块的导航。利用硬件实现的历元叠加及其数据整合模块具有处理速度快、设备紧凑、功耗低的特点,为航天器利用X射线脉冲星导航提供了一种可行的硬件数据处理技术上的支持。     

存在观测站位置误差的转发式时差无源定位

无源定位中,由于观测站安放在运动平台等原因造成的观测站位置误差会影响无源定位精度性能。另外到达时间差(简称时差)(TDOA)的转发式测量需要将不同观测站截获到的辐射源信号都转发到同一位置,如主观测站。针对这两个问题,提出了基于约束总体最小二乘(CTLS)的无源定位算法。首先将转发式时差的非线性定位方程转化为不需要中间变量的直接线性方程,再基于CTLS算法依次转化为约束优化问题和无约束优化问题,最后推导给出定位近似闭式解。仿真实验表明在观测站误差较大时,该算法与其他算法相比定位精度性能较好。     

Gust response analysis and wind tunnel test for a high-aspect ratio wing

A theoretical nonlinear aeroelastic response analysis for a flexible high-aspect ratio wing excited by harmonic gust load is presented along with a companion wind tunnel test. A multidisci-plinary coupled numerical calculation is developed to simulate the flexible model wing undergoing gust load in the time domain via discrete nonlinear finite element structural dynamic analysis and nonplanar unsteady vortex lattice aerodynamic computation. A dynamic perturbation analysis about a nonlinear static equilibrium is also used to determine the small perturbation flutter bound-ary. A novel noncontact 3-D camera measurement analysis system is firstly used in the wind tunnel test to obtain the spatial large deformation and responses. The responses of the flexible wing under different static equilibrium states and frequency gust loads are discussed. The fair to good quanti-tative agreements between the theoretical and experimental results demonstrate that the presented analysis method is an acceptable way to predict the geometrically nonlinear gust response for flex-ible wings.     

正十七烷与正十八烷对航空煤油理化性能及液滴平均直径的影响

讨论了正十七烷与正十八烷(C₁₇,C₁₈)对燃料运动黏度、密度、表面张力理化性能的影响,探究了直链烷烃对SMD(Sauter mean diameter)的影响.将Key's混合规律、Tat混合规律和多项式拟合应用于密度公式的拟合,并将Key's混合规律与对数拟合应用于运动黏度公式的拟合,得出的理化性能拟合公式精度较高;通过测量纯煤油及C₁₇,C₁₈混合油雾化的SMD,实验发现随着直链烷烃的质量分数的增加,混合油的运动黏度增加,SMD也随之增加,雾化效果与纯航空煤油的相比较差,而C₁₈混合油的SMD要比C₁₇混合油要大,并且利用密度、运动黏度的拟合公式对SMD进行预测的偏差小于0.3%.      

2.5维机织复杂结构件的静强度

采用宏细观结合方法,针对经纱和纬纱等材料组分可能发生的多种失效模式,分别建立了基于改进的Hashin准则的系统性的材料失效准则及不同失效模式下的刚度退化模型.引入逐渐损伤的思想,建立了2.5维机织复杂结构件静强度系统性分析方法.模拟并分析了材料经向拉伸和纬向拉伸的应力-应变曲线,与实验得到的材料应力-应变曲线相比,相同应变下应力误差不超过6.5%,具有较好的重合度;对2.5维机织压气机静子连接结构模拟件开展了逐渐损伤模拟,结果表明:结构损伤主要集中在叶根倒角附近,其中吸力面叶根处的基体压缩失效形式会引起结构大幅变形,是结构破坏的主要原因.      

一种减少失速保护虚警率的混合滤波方法

针对飞机失速保护设计过程中易出现虚警的情况,提出一种基于FIR和传统滤波器相结合的混合滤波方法。结合飞机本体的运动特征,对参与失速保护逻辑运算的两个重要参数,即侧向加速度和迎角信号进行频率分析,基于信号的特征设计混合滤波器,然后采用Simulink滤波工具箱设计滤波器对信号进行滤波处理。仿真结果表明该方法能够减少虚警率的发生,特别是大背景噪声下的虚警率能够得到较好抑制,验证了滤波器设计正确性,从而提高失速保护功能对适航条款符合性。该滤波器设计方法,不但可以有效解决本文提到的问题,对于其他涉及信号处理的系统设计同样具有借鉴意义。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.